FORD FLTM BU 120-1-2000 WEATHERSTRIP TAPES (HEAT-BONDABLE) - 90 DEGREE PEEL ADHESION.pdf

1、 FORD LABORATORY TEST METHOD BU 120-01 Date Action Revisions 2000 12 01 Revised Editorial no technical change A. Cockman 1990 03 15 Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. WEATHERSTRIP TAPES (HEAT-BONDABLE) - 90 DEGREE PEEL ADHESION Application This

2、 method describes the procedure for testing 90 degree peel adhesion of foam tapes having a pressure sensitive adhesive on one side and a heat activated adhesive on the other side. The heat activated adhesive is heat bonded to an anodized aluminum foil to reinforce the foam. Apparatus Required Tensil

3、e Tester Instron or equivalent; capable of a constant rate of extension of 300 mm per minute. Test Fixture Equipped with a ball bearing track allowing for a continuous 90 degree peel angle of the tape from the panel (refer to Figure 1). Hand Roller 6.5 kg mass Electric Iron or Hot Press Capable of m

4、aintaining 150 +/- 3 C. Materials Required Panel Freshly painted panel 50 x 300 mm Anodized Aluminum Strip .127 (nominal) x 16 x 200 mm Tissues Laboratory grade; lint free. Masking Tape 25 mm wide roll. Isopropyl Alcohol/Distilled Water Solution 50:50 by volume. FORD LABORATORY TEST METHOD BU 120-01

5、 Page 2 of 3 Copyright 2000, Ford Global Technologies, Inc. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same

6、conditions unless otherwise specified. Procedure 1. Clean the painted panel with one wash using the isopropyl/water solution and wipe dry with a tissue. 2. Cover 25 mm of one of the 50 mm ends of the test panel with masking tape. Refer to Figure 1. 3. Cut a specimen of the tape to be tested at least

7、 200 mm long and 12.7 mm wide. 4. Lay the tape to be tested flat with the heat activated adhesive exposed. 5. Lay the anodized aluminum strip on top of the heat activated adhesive, such that the tape is centered and parallel to the edges of the strip with the aluminum matte surface against the adhes

8、ive. 6. Apply a 150 +/- 3 C iron or hot press to the top of the aluminum for 15 s. 7. Roll the tape/aluminum sample with the 6.8 kg roller. 8. Remove the liner from the tape. Align the tape lengthwise 25 mm in from the edge as shown in Figure 1, and allow the end of the tape to extend beyond the end

9、 of the panel by 50 mm. 9. Roll the tape sample onto the panel with one pass using the 6.8 kg roller at the rate of 300 mm per minute. 10. Allow the specimen to age as specified in the applicable Engineering Materials Specification. 11. Test the panels after conditioning as follows: . Clamp the fixt

10、ure for holding the panel in the stationary jaw of the tensile tester. . Place a test panel into the holding fixture and insert an extended end of the tape into the crosshead jaw. FORD LABORATORY TEST METHOD BU 120-01 Page 3 of 3 Copyright 2000, Ford Global Technologies, Inc. . Initiate jaw separati

11、on at 300 mm per minute. Continue the test until all of the tape has been removed from the panel. . Return the crosshead jaw to the original position. 12. Record the average peel force. 13. Repeat Steps 1 through 12 for two additional tape/aluminum samples and average the results of the three samples. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Figure 1 Weatherstrip Tape 90 Peel Test