FORD FLTM BU 155-01-2018 ADHESION TEST FOR TERMINALS AND CONNECTORS ON AUTOMOTIVE GLASS OR COATED POLYCARBONATE SUBSTRATE.pdf

1、 FORD LABORATORY TEST METHOD BU 155-01 Date Action Revisions Rev. 01 2018 04 18 Revised See Summary of Revision P. Konopka, R.Surowiec, NA 2007 09 25 Activated M. Mehandru/C. Ridgard Controlled document at www.MATS Copyright 2018, Ford Global Technologies, LLC Page 1 of 8 ADHESION TEST FOR TERMINALS

2、 AND CONNECTORS ON AUTOMOTIVE GLASS OR COATED POLYCARBONATE SUBSTRATE Application These procedures are used to determine the adhesion properties of connectors when adhered to automotive glass or coated polycarbonate substrate. A shear test and a tension test will be administered. Apparatus Required

3、Mechanical Testing Equipment The mechanical testing equipment must be able to apply a tension force at a rate of 125 +/-25 mm/min. An example of the mechanical testing equipment is shown below in Figure 1. Figure 1 Load Cell A load cell no larger than 455 kg is to be used. Pull Wire For the tension

4、test in section two, wire or similar material that can be threaded through the connector and made to mate with the load cell portion of the test equipment will be needed. The only requirement is that the wire or similar material be able to withstand the 100 N tension force it will transmit to the te

5、st specimen. FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 2 of 8 Test Samples Plaques for the tension test must be prepared with a connector that is pre-drilled such that pull-wire can be threaded through the connector. Sample Preparation Preparing the sam

6、ple i.e. cleaning the surface, attaching the connector should be done according to manufacturers recommendations that reflect their manufacturing process. For the tension test, pre-drilling the connector should also be done according to the manufacturers recommendations. Conditioning and Test Condit

7、ions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Note: Chemicals, materials, parts, and equipment r

8、eferenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Procedure 1) Shear: Using mechanical tensile testing equipment, connectors must be pulled in a shear method (Parallel to the plaque surface). 1.1 Lock th

9、e sample into the test apparatus/fixture and apply a female connector pull jig as shown in figure 2 below. Images of test set-up are provided in figures 2.1, 2.2, 2.3, and 2.4. Figure 2 FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 3 of 8 Figure 2.1 Fixture

10、 used in connector shear test Figure 2.2 Female connector pull jig with hole FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 4 of 8 Figure 2.3 Female pull jig mated to connector Figure 2.4 Close-up of pull jig mated to connector 1.2 Following the equipment ma

11、nufacturers instructions, apply a shear force by moving the load cell away from the fixture at a rate of 125 25 mm/minute. Continue shearing until the connector is sheared off. FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 5 of 8 2) Tension: Using mechanica

12、l tensile testing equipment, connectors must be pulled in a tension test at 90 to the substrate. 2.1 Plaques must be prepared with connectors that are pre-drilled in a configuration that pull wire can be threaded through the connector clip. 2.2 Lock the sample into the test apparatus and attach the

13、wire pull jig as shown in figure 3 below. See figures 3.1 through 3.7 for examples of test set-up. Figure 3 Figure 3.1 Connector with drilled hole FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 6 of 8 Figure 3.2 Connector soldered to defroster bus bar Figure

14、 3.3 Wire threaded through connector FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018, Ford Global Technologies, LLC Page 7 of 8 Figure 3.4 Wire is twisted to create a loop to secure it to test equipment Figure 3.5 View of tension test set-up FORD LABORATORY TEST METHOD BU 155-01 Copyright 2018,

15、 Ford Global Technologies, LLC Page 8 of 8 Figure 3.6 Close-up of tension test Figure 3.7 Tension test in progress 2.3 The fixture moves freely in the horizontal plane to ensure the pull direction is always 90 to the surface during testing. 2.4 Follow the equipment manufacturers instructions to appl

16、y a pull force by moving the load cell away from the fixture at a rate of 125 +/- 25 mm/minute. Continue pulling until the connector is pulled off. Reporting Report force at failure and failure mode for each sample. Summary of Revisions 2018 04 18 Title, Application & throughout document, removed “defroster” to include all terminals and connectors, added glass.