ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:42.84KB ,
资源ID:747862      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747862.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM EU-BU 003-02-2000 BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES《金属对金属胶粘剂的块样剪切强度》.pdf)为本站会员(孙刚)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM EU-BU 003-02-2000 BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES《金属对金属胶粘剂的块样剪切强度》.pdf

1、 FORD LABORATORY TEST METHOD EU-BU 003-02 Date Action Revisions 2000 11 13 Revised Editorial no technical change A. Cockman 1994 02 28 Printed copies are uncontrolled Page 1 of 5 Copyright 2000, Ford Global Technologies, Inc. BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES Application This procedur

2、e is used to test the block shear strength of thermosetting adhesives used for bonding metal to metal. Apparatus Required Press An air driven press which will deliver a constant pressure to the test specimens during cure is required. The press is equipped with controlled electric heaters which heat

3、the test specimens to required temperature during cure under pressure (see Drawing 1). Mechanical Convection Oven Capable of mainta ining a temperature of 80 +/ - 2 C. Tensile Tester A tensile testing machine with a scale range of 0 - 100 KN and capable of a load at a uniform rate of 10 mm/minute is

4、 required. The tensile machine shall have an indicator for recording the shear strengt h of the adhesive in Newton at the moment of rupture. Shear Strength Fixture The fixture for holding the bonded test specimen during loading is shown in the attached Drawing 1. The fixture is equipped with an elec

5、trically controlled heater for determinin g shear strength at elevated temperatures. Abrasive Paper or Sand Blast (a) Abrasive Paper Type: KK 14; Size: 230 x 280 mm; Grit Size: 150 Used for polishing the mating surfaces of the test specimens or sand blast (depending on surface desired). Sourc e: V.S

6、.M Abrasive or Vereinigte Schmirgel and Maschinenfabriken AG Watford, England 3 Hannover Hainholz, Germany FORD LABORATORY TEST METHOD EU-BU 003-02 Page 2 of 5 Copyright 2000, Ford Global Technologies, Inc. (b) Sand Blast Sand or Grit Size Retained on 20 Sieve - 12 % maximum Retained on 50 Sieve - 1

7、 % maximum Operating Pressure 700 N/ m Exposure Time 50 seconds per 10 cm Nozzle Distance to Specimen 75 mm Nozzle Size 9.5 mm Test Specimens East test specimen assembly consists of one strip and one disc of BS 1474: 1969 HE 15 TB or DIN 1725 BL 1 AlCuMg 1F40 3.1325 aluminum. The strip is 28 mm by 1

8、11 mm by 6.0 mm and the disc is 28 mm in diameter by 6.0 mm thick, with a hole in the centre of the disc to give a firm fit over the pin in the press. Tetrachloroethylene To clean the test specimen. Paper Masking Tape Normal paint shop masking tape with dimensions 25 mm wide x 0.17 mm thick to build

9、 up the required layers. Spring Paper Clips “Bulldog“ type or similar. Jaw width approximately 63 mm to fix the test sample assembly. Surgical Scalpel To scribe marks at positioning points . Spatula To spread and level the applied adhesive. Conditioning and Test Conditions All test values indicated

10、herein are based on material conditioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h pr ior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Prepare the mating surfaces of the aluminum strips and discs to

11、give a uniform finish, by using abrasive paper or sand blast. 2. Wipe clean with a cloth wetted with tetrachloroethylene. 3. Lay the required number of prepared aluminum strips on a flat surface. Ensure that the long edges are touching and parallel. FORD LABORATORY TEST METHOD EU-BU 003-02 Page 3 of

12、 5 Copyright 2000, Ford Global Technologies, Inc. 4. On the last panel at each end of the series make 2 light scribe marks a minimum of 28 mm apart and equidistant from the longitudinal mid point of the panel. 5. Using the scribe marks as positioning points, lay 3 layers of masking tape across the p

13、anels so as to leave a gap of approximately 28 mm across the centre of each panel. At one end leave an excess of about 80 mm of tape which can be doubled under to make a 40 mm tab with which to pull the tape away from the panels when required. See drawing No. 2. 6. Spread the adhesive evenly along t

14、he gap then level off with a spatula and remove excess. Note: The build - up of 3 layers of 0.17 mm tape will assist in leveling a 0.50 mm layer of wet adhesive across the centre of each specimen, which will produce approximately 0.17 mm dry film thickness when using a 40 % total solids adhesive. To

15、 obtain 0 .15 - 0.20 total dry film thickness with lower total solids material, additional thickness of tape will be required. For example, a 26 % solids adhesive would require a buildup of 4 layers of 0.17 mm tape. 7. Secure the aluminum test strips with spring c lips at either end so as to restric

16、t movement of the strips when the tape is removed. 8. Carefully remove the masking tape by pulling upwards from the end with the excess tape. See Drawing 2. 9. Air dry for 15 minutes. 10. Bake to give 20 minutes at 80 +/ - 2 C metal temperature. 11. Cool to 23 +/ - 2 C and remove clips. 12. Separate

17、 the specimens carefully by slitting through the adhesive with a surgical scalpel at each junction. 13. Bond an aluminum disc to each strip so that the prepared surface i s in contact with the adhesive. Use light finger pressure to ensure even contact. 14. Position the test assembly in the press, lo

18、cating the hole in the disc over the pin in the press, and apply the specified load at the specified time and temperature as required by the material specification. 15. Allow the bond test assemblies to cool, position each assembly in the test fixture for shear adhesion (see drawing) and apply a loa

19、d at 10 mm per minute to failure of the bond at the temperature specified in the material specification. Evaluation Report shear strength of the specimen, test temperature, type of adhesive, cure time and temperature. All specimens must meet the requirements of the relevant Material Specification. C

20、hemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD EU-BU 003-02 Page 4 of 5 Copyright 2000, Ford Global Technologies, Inc. BLOCK SHEAR STRENGTH OF METAL TO METAL ADHESIVES BLOCK SHEAR STRENGTH TEST FIXTURE ( EXPLODED VIEW ) FORD LABORATORY TEST METHOD EU-BU 003-02 Page 5 of 5 Copyright 2000, Ford Global Technologies, Inc.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1