FORD M14J210-1991 AROMATIC HYDROCARBON THINNERS (Shown on M14J200-A SEE SCOPE)《芳烃稀释剂 列于标准M14J200-A上见范围》.pdf

1、NON-PRODUCTION mTERIAL SPECIFICATION cam Date 1991 o9 o1 Material Name Specification Number Action Changes AROMATIC HYDROCARBON THINNERS M14 J2 0 O-A 1. SCOPE: This standard establishes physical and chemical properties for the following aromatic hydrocarbon thinners: M-14 J2 42 (M-542 ) Toluol M-14

2、J2 4 5 (M-54 5 ) Xylol - 10 deg M-14 J2 O 8 (M-4 60 8 ) Petroleum Hi-Flash Naphtha M- 14 J2 17 (M-4617) Special Petroleum Fraction M- 14 J2 2 O (M-4 62 O ) Solvent Heavy Petroleum Fraction M-14J260 (M-4 6 60 ) High Solvency Heavy Petroleum Naphtha M-14 J2 1 O (M-14 J1 O ) Special Thinner for Dual Pu

3、rpose Enamels 2. APPLICATION: These thinners are used for reducing enamels and primers to the desired viscosity. For specific applications 3. REQUIREMENTS: 3.1 SPECIFIC GRAVITY AT 60/60 F (ASTM D 891): M-14J242 M-14J217 M-14J208 M-14J245 M-14J210 M-14J220 M-14J260 (M-542 ) (M-4617) (M-4608) (M-545)

4、(M-14J10) (M-4620) (M-4660) .866-.873 .790-.810 .835-.850 .860-.870 .865-.880 .850-.865 .885-.898 WT./CAL. LBS.: M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 7.22-7.28 6.59-6.75 6.97-7.08 7.16-7.25 7.20-7.33 7.08-7.2 7.3

5、8-7.44 3.2 FLASH POINT (MIN) F (ASTM D 56) : M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 38 24 80 80 110 135 145 Page 1 of 3 NON-PRODUCTION mTERIAL SPECIFICATION am M-14 J2 O O-A 3.3 MIXED ANILINE PT. (MAX) C (ASTM D 61

6、1) : M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 15 43 33 15 20 37 20 MIXED ANILINE PT. (MAX) C (FORD LABORATORY TEST METHOD BJ 4-1): M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-46

7、08) (M-545) (M-14J10) (M-4620) (M-4660) 10 38 28 10 15 32 15 3.4 OF LAST 10% DISTILLED (ASTM D 1012) : No higher than mixed aniline point of shipment as received 3.5 COLOR (MIN) (ASTM D 156) : M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10)

8、(M-4620) (M-4660) 25 25 25 25 25 25 25 3.6 NON VOLATILE (MAX) (ASTM D 268) MG/100 ML: M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 1.0 2 5 1.0 3 5 5 3.7 COPPER STRIP (MAX) (ASTM D 130) : M-14J242 M-14J217 M-14J218 M-14J2

9、45 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 2c 2c 2c 2c 2c 2c 2c 3.8 ACID WASH COLOR (MAX) (ASTM D 848) : M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 6 6 10 6 6 10 6 3.9 K

10、AURI-BUTANOL (MIN) (ASTM D 1133) : M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 105 70 74 95 88 74 88 3.10 DISTILLATION RANGE F (ASTM D 850) : 1BP MIN: M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 M-14J260 (M-54

11、2) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) (M-4660) 221 203 270 275 310 347 355 Page 2 of 3 NON-PRODUCTION mTERIAL SPECIFICATION am M-14 J2 O O-A 10% MIN: M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) 2 12 287 315 355 50% MAX: M-14J24

12、2 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) 248 325 330 380 90% MAX: M-14J242 M-14J217 M-14J218 M-14J245 M-14J210 M-14J220 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) 257 345 350 3 92 DP MAX: M-14J242 M-14J217 M-14J218 M-14J245 M-14J21

13、0 M-14J220 (M-542) (M-4617) (M-4608) (M-545) (M-14J10) (M-4620) 235 275 370 2 93 355 420 3.11 SUPPLIERS RESPONSIBILITY: All material supplied to this 4. 5. 5.1 M-14J260 (M-4 6 60 ) 3 64 M-14J260 (M-4 6 60 ) 383 M-14J260 (M-4 6 60 ) 3 95 M-14J260 (M-4 6 60 ) 422 standard must be equivalent in all cha

14、racteristics to the material upon which approval was originally granted and shall be suitable for the intended application. APPROVAL OF NEW SUPPLIERS: Materials submitted by new suppliers to this standard must have laboratory approval. Recommendations for the addition of new suppliers to Manufacturi

15、ng Standards Bulletins, along with approved laboratory reports, must be made in writing to the Materials and Equipment Engineering Department, Manufacturing Engineering & Development Office in accordance with Manufacturing Procedure IId1. GENERAL INFORMATION: FLAMMABILITY AND/OR TOXICITY: These mate

16、rials represent a potential fire and/or health hazard. The Manufacturing Engineering Department must notify both the Plant Security and the Safety personnel of its presence in the plant to assure that proper fire and/or health precautions are provided. The location in which it is used or stored must be included in the notification. Page 3 of 3