FORD M2C142-F-2009 LUBRICANT SULFUR PHOSPHOROUS E P COMPOUND (Shown on M2C142-A)《含硫磷类E P 添加剂的润滑油 列于标准M2C142-A上》.pdf

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 14 N-STATUS No Replacement Named L. Sinclair, FNA 1984 02 01 Page 1 of 3 LUBRICANT, SULFUR PHOSPHOROUS E.P. COMPOUND M2C142A-F NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material defined by this st

2、andard is an extreme pressure lubricant consisting of refined mineral oil with a sulfur-phosphorous additive. 2. APPLICATION: This material shall be suitable for use as a transmission gear lubricant and/or where specified. 3. REQUIREMENTS: M2C142A M2C142B M2C142C M2C142D M2C142E M2C142F 3.1 VISCOSIT

3、Y: (ASTM D 455 & D 2161) AGMA Grade 2 EP 4 EP 6 EP 7 EP 8 EP - (SAE 80) (SAE 90) (SAE 140) cST 38.0 C 68 150 320 460 680 1425 cSt 98.9 C 8.6 14.4 23.2 29.0 37.2 59.3 SUS 38.0 C 315 700 1500 2150 3150 7000 SUS 98.9 C 54.4 75.7 112 138 175 277 3.2 VISCOSITY INDEX: 90 min 90 min 90 min 90 min 90 min 90

4、 min (ASTM D 2270) 3.3 FLASH POINT:C 204 min 204 min 204 min 232 min 232 min 232 min (ASTM D 92) 3.4 FIRE POINT:C 232 min 232 min 232 min 260 min 260 min 260 min (ASTM D 92) 3.5 POUR POINT:C -23 max -23 max -18 max -12 max -9 max -4 max (ASTM D 97) 3.6 SULFUR: % wt, min 0.70 0.70 0.70 0.70 0.70 0.70

5、 (ASTM D 129) PHOSPHOROUS, % wt 0.03 0.03 0.03 0.03 0.03 0.03 (ASTM D 1091),min 3.7 EXTREME PRESSURE: 60 lbs 60 lbs 60 lbs 60 lbs 60 lbs 55 lbs Test Timken, min min min min min min Lever Load (FLTM BJl-2) NON-PRODUCTION MATERIAL SPECIFICATION M2C142A-F Page 2 of 3 3.8 DEMULSIBILITY: (ASTM D 2711) Fr

6、ee Water ml(min) 85 85 85 85 85 85 Emulsion ml (max) 1.0 1.0 1.0 1.0 1.0 1.0 3.9 OXIDATION STABILITY: (ASTM D 2893) 10 max 10 max 10 max 10 max 10 max 10 max Viscosity Increases % 3.10 COPPER STRIP TEST: (ASTM D 130) 3 hours at 38C 2A max 3.11 INHIBITORS: These lubricants shall contain suitable addi

7、tives to inhibit oxidation, rust and foaming. 3.12 TOXICITY: This material shall not contain any skin sensitizers, primary irritants or other ingredients considered harmful to employee health under normal use conditions. 3.13 COMPOSITION: The material supplied must be of uniform texture and consiste

8、ncy and must not become rancid or show component separation. Materials compounded with recycled oil shall be so identified. 3.14 COMPATIBILITY: All material to this Standard shall be compatible in all proportions with other materials currently approved under these “M“ numbers. Separation, precipitat

9、ion or flocculation of solids or gels shall not be permitted. 3.15 SUPPLIERS RESPONSIBILITY: All materials supplied to this standard must be equivalent in all characteristics to the material upon which approval was originally granted and shall be suitable for the intended application. Changes in com

10、position shall not be made with- out approval of the Plant Engineering Office, Manufacturing Staff. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this Standard must have Industrial Hygiene, Environmental Engineering, Laboratory and Shop Trial approvals. Suppliers are requ

11、ired to complete and submit the Material Health and Safety Data Sheet, Form 1291, the Mandatory Reporting of Critical Materials, Form 68-100, prior to shop trial. Recommendations for the addition of new manufacturers to the Manufacturing Approved Source List (ASL) must be made in writing to the resp

12、onsible Manufacturing Staff office by the appropriate Divisional Standards activity in accordance with Manufacturing Procedure IId1. NON-PRODUCTION MATERIAL SPECIFICATION M2C142A-F Page 3 of 3 5. ENVIRONMENTAL CONTROL: Use of any material approved to this standard must comply with the guidelines as

13、established in the environmental review of the material, as they appear in the Materials and Toxicology (MATS) System. 6. HEALTH AND SAFETY: The following are recommended practices to be observed when working with petroleum products: a. When contact with oil is unavoidable, impervious gloves should

14、be worn as well as clean work clothes. b. When skin exposure cannot be avoided, removal of oil from the skin should be as prompt as possible. A mild soap or skin cleanser and water should be used to remove oil. Industrial solvents should not be used to clean the skin. c. All skin rashes, lesions, cuts and abrasions should receive prompt medical attention.