FORD M2C173-B-2009 OIL LUBRICATING HIGHLY REFINED《高精炼润滑油 列于标准FORD M2C173-A上》.pdf

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 15 N-STATUS No Replacement Named L. Sinclair, FNA 1988 05 01 Page 1 of 2 OIL, LUBRICATING, HIGHLY REFINED M-2C173A-D NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material desired under this standard

2、is a highly refined, inhibited, noncorrosive petroleum oil. 2. APPLICATION: This oil is generally used for lubrication of plain and antifriction bearings of high speed spindles in grinders and other machine tools, where noncorrosive and oxidation resisting characteristics are required. 3. REQUIREMEN

3、TS: M-2C173A M-2C173B M-2C173C M-2C173D 3.1 GRAVITY: (A.P.I.) (ASTM D 287) 33.0 min 30.0 min 30.0 min 29.2 min 3.2 VISCOSITY: cSt at 37.8 C 1.81-2.94 10.3-13.1 21.7-25 92-96 (ASTM D 445) 99 C 2.05 max 2.35-2.94 3.86-4.79 10.1-12.1 3.3 FLASH POINT: (min) 66 C 149 C 177 C 200 C (ASTM D 92) 3.4 FIRE PO

4、INT: (min) 71 C 177 C 205 C 230 C (ASTM D 92) 3.5 COLOR: (max) 2 2 2 2.5 (ASTM D 156) 3.6 POUR POINT: (max) -7 C -7 C -7 C -4 C (ASTM D 97) 3.7 COPPER STRIP CORROSION: 0 0 0 0 (ASTM D 130) 3.8 NEUTRALIZATION NUMBER: 0.01 0.01 0.02 0.02 (ASTM D 664) 3.9 RESISTANCE TO RUST: (ASTM D 665) Distilled Wate

5、r No rust No rust No rust No rust Synthetic Sea Water No rust No rust No rust No rust 3.10 OXIDATION STABILITY: 750 750 750 750 (ASTM D 943) Minimum hours before oil reaches acid number of 2.0 NON-PRODUCTION MATERIAL SPECIFICATION M-2C173A-D Page 2 of 2 3.11 RESISTANCE TO FOAMING: No foam No foam No

6、 foam (ASTM D 892) 3.12 COMPATIBILITY: All materials to this Standard shall be compatible in all proportions with other materials currently approved under these “M“ numbers. Separation, precipitation or flocculation of solids or gels shall not be permitted. 3.13 SUPPLIERS RESPONSIBILITY: All materia

7、ls supplied to this Standard must be equivalent in all characteristics to the material upon which approval was originally granted and shall be suitable for the intended application. Changes in composition shall not be made without approval of Plant Engineering Office, Engineering and Manufacturing S

8、taff. 3.14 IDENTIFICATION: Materials supplied to this standard shall be identified with the “M“ number printed on the side as well as the top of the containers in letters at least 2 inches (50mm) high in a contrasting color to that of the container. Container marking shall be in accordance with Manu

9、facturing Standard ZF-10 and conform to all Federal, State and Local container contents labeling regulations which are in effect both in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers for qualification to this standard must have Industrial Hygien

10、e, Environmental Engineering, Laboratory and Shop Trial approvals. Suppliers are required to complete and submit the Material Health and Safety Data Sheet and the Environmental Data Sheet (Form 1291A) prior to Shop Trial. Recommendations for the addition of new manufacturers to the Manufacturing App

11、roved Source List (ASL) must be made in writing to the responsible Manufacturing Staff office by the appropriate divisional standards activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONTROL: Use of any material approved to this Standard must comply with the guidelines as e

12、stablished in the environmental review of the material, as they appear in the Materials and Toxicology (MATS) System. 6. HEALTH AND SAFETY: Use of any material approved to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS system.