1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 14 N-STATUS No Replacement Named L. Sinclair, FNA1991 12 01 Page 1 of 2 EMULSIFIABLE LUBRICATING OIL, PNEUMATIC M2C81-A POWER TOOLS AND EQUIPMENT NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material
2、 desired under this standard is a highly refined oil, compounded with suitable additives to improve its water emulsifying and rust-inhibiting characteristics as well as film strength and wetting properties. 2. APPLICATION: This material was originally released for application in lubricating systems
3、to eliminate the effects of free moisture in com- pressed air by absorbing the moisture and forming a stable oil-in-water emulsion. Additionally, the material is intended to promote longevity of cup leathers, packings O-rings and seals. 3. REQUIREMENTS: 3.1 GRAVITY: At 60F (15.6C) (A.P.I.): 24 min (
4、ASTM D 287) 3.2 VISCOSITY: (ASTM D 445 and D 2161) At 100F (37.8C) 15.7-27.3 cSt(mm2/s), 80-130 SUS At 210F (98.9C) 2.65-4.18 cSt(mm2/s), 35-40 SUS 3.3 FLASH POINT: 325 F (163 C) min (ASTM D 92) 3.4 FIRE POINT: (ASTM D 92) 360 F (182 C) min 3.5 WATER ABSORPTION: 80 cc min Test method: Titrate 20 cc
5、of oil with distilled water until water separation begins to show. Report cc of water absorbed. 3.6 POUR POINT: Minus 45 F (Minus 43 C) max (ASTM D 97) 3.7 CORROSION TEST: No pitting; moderate stain (FLTM BJ 7-1 except add 5% water by volume) 3.8 SULFUR: 0.10% min (ASTM D 129) 3.9 RECOVERED SAPONIFI
6、ABLES: 1.0% min (FLTM AJ6-1) NON-PRODUCTION MATERIAL SPECIFICATION M2C81-A Page 2 of 2 3.10 ANILINE POINT: 156 - 170 F (69 - 77 C) (ASTM D 611) 3.11 NEUTRALIZATION NUMBER: 0.15 max (ASTM D 664) 3.12 ASH: 0.10 max (ASTM D 482) 3.13 CARBON RESIDUE: % 0.10 max (ASTM D 189) 3.14 CHANGE IN SEAL PROPERTIE
7、S: (% Volume Change) 0-11 (ASTM D 471, 70 h at 212F (100C) SAE-J200 2 CH720A25G14E015E035F17 (Western Rubber 37-22, Buckeye Rubber 28-10 and 456-10) 3.15 GUMMING AND STICKING: This material shall not occasion varnishing or gumming nor cause sticking of valves, etc. when in contact with moisture in c
8、ompressed air systems, as verified by shop trial. 3.16 ATOMIZATION AND SEPARATION: This material must flow freely in all air line lubrication systems. No visible oil separation should occur on bronze wicks when used in bronze wick type lubricators, as verified by shop trial. 4. STANDARD PARAGRAPHS: The following standard paragraphs as defined in Manufacturing Standard MCX, are herewith made a part of this standard: A5, C1, P1, P2, P3, R1, R2.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1