FORD SB3-17-1988 NONWOVEN DISPOSABLE GARMENTS FOR PAINT SPRAY PERSONS《喷漆人员用无纺一次性服装》.pdf

1、 Manufacturing StandardsFord Motor Company198807 NONWOVEN DISPOSABLE GARMENTS FOR SB3-17PAINT SPRAY PERSONSEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 1 of 31. SCOPE: The garments under this standard are made of a spun bonded olefin(Tyvek). Material is to

2、be nonstatic and nonlinting.2. APPLICATION: These garments, in the form of coveralls, pants, shirts,head covers and shoe covers are to be worn by paint spray persons andtack-off personnel in enamel paint spray booths.3. REQUIREMENTS: Material used in the construction of these garments shallbe breath

3、able Tyvek Type No. 1622.This material is to be resistant to mildew, odorless, nontoxic, rash-freeand safe for the intended use. It shall not be affected by paints andthinners in use in the paint booths. The garments shall be comfortable,opaque, and resistant to paint bleed, and the materials shall

4、have goodabrasion resistance.3.1 MATERIAL COMPOSITION AND CONSTRUCTION: The material shall benonlinting spunbonded olefin except for metallic components, such asbuttons and zippers.Tyvek No. 1622a. Basic Weight 1.15 o. per sq. yd. (33 g.)b. Thickness (mils) 6 mils (0.006 in.)c. Breaking StrengthMach

5、ine Direction (MD) 6.0 lbs./in. MD (2722 g.) minCross Direction (XD) 8.0 lbs./in. XD (3629 g.) mind. Tongue Tear 1.5 lbs. MD (680 g.) min1.7 lbs. XD (771 g.) mine. MIT Flex, Cycles Greater than 100,000f. Frasier Porosity More than 1 ft.3/ft.2/min.3.2 COLOR: White (high opacity), unless otherwise spe

6、cified.3.3 STATIC PROTECTION (NFPA 56A STATIC PROTECTION TEST):At indicated 70 F (39 C), 50% R.H.a. RESISTIVITY:Log R*Charge DecayFace Back Seconds to DischargeMD XD MD XD MD XDTyvek1622 8.4 8.6 8.7 8.5 Less than .1 Less than .1*Log R greater than 11.0 = FailureManufacturing StandardsFord Motor Comp

7、any198807 NONWOVEN DISPOSABLE GARMENTS FOR SB3-17PAINT SPRAY PERSONSEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 2 of 3b. FLAMMABILITY - CLASS I, LOW FLAMMABILITY:(NFPA 702, 45 Degree Edge Ignition Flammability Test)Ignition Self-Extinguishing % Consumed Cl

8、assTyvek1622 MD 1.1 sec. 4.4 sec. 4 I.B.E.*1622 XD 1.1 sec. 4.8 sec. 3 I.B.E.*Ignited but extinguished (I.B.E.)c. FINISH: No finish of any kind shall be applied to the materialthat would reduce anti-static properties or increase linting.d. GARMENT CONSTRUCTION: All seams shall be double needle locks

9、titched to firmly envelope raw edges. Synthetic continuousfilament thread shall be used throughout. Size of garment shallbe labeled.e. COVERALLS: Coveralls shall be full cut, with fly front,synthetic tape zipper or Scovill snap fasteners to crotch.Garment shall be finished clean inside and out. Only

10、 raglansleeves to be used.3.4 SIZING:3.4.1 Coveralls:XXX XXXXX-Sm Sm Med Lg X-Lg XX-Lg -Lg -Lg(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)_Chest 42 46 49-1/2 55 57 59 74 74Waist 42 46 49-1/2 55 57 59 74 74Inseam 27 28 28 30 32-1/2 33 34 34Sleeve 31 33 35 35 36 37-1/4 40 45Length 59-1/2 62 63 65-1

11、/2 69-1/2 70-1/4 71 763.4.2 SHIRTS: Shall be full cut with same closure systems ascoveralls. Only set-in sleeves to be used.X-Small Small Medium Large X-Large(in.) (in.) (in.) (in.) (in.)_Chest 46 49 53 56Sleeve 31 32-1/2 33-1/2 34 35Manufacturing StandardsFord Motor Company198807 NONWOVEN DISPOSABL

12、E GARMENTS FOR SB3-17PAINT SPRAY PERSONSEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 3 of 33.4.3 PANTS: Shall be full cut with elasticized waist or drawstring, as specified by issuing division:X-Small Small Medium Large X-Large(in.) (in.) (in.) (in.) (in.)_

13、Waist 36 40 43 46 52Inseam 26 28 29 32 333.4.4 POCKETS AND OPENINGS: Where pockets are specified, they shallbe on inside only. They shall be made from same material asgarment. Sizes shall be as follows:Patch breast pockets: 6 in. (152mm) deep x 5-1/2 in.(140mm) widePatch hip pockets: 8-1/2 in. (216m

14、m) deep x 8 in.(203mm) wideSide openings foraccess to interior: 6 in. (152mm) must be die-cut.4. ACCESSORY GARMENTS: Hoods, caps, snoods, and shoe covers shall beprovided only when specifically called for by issuing division and shallbe attached on the inside of the garment. When required, they shal

15、l beconstructed of the same material and in the same manner indicated above.They shall be snug and impervious to hair and dandruff particles.5. PACKAGING: All garments to be packaged 25 pieces per case. Outside ofall cases to signify proper shipping, address, manufacturer, Ford codenumber, Ford purc

16、hase order number, item enclosed, and number of garmentsinside case.6. SUPPLIERS RESPONSIBILITY: All material supplied to this standard shallbe equivalent in all characteristics to the material upon which approvalwas originally granted and shall be suitable for the intendedapplication.7. APPROVAL OF

17、 NEW SUPPLIER: Garments submitted by new manufacturers tothis standard must have purchasing source approval and laboratory andshop trial approvals. Recommendations for the additions of newmanufacturers to the Manufacturing Approved Source List (ASL)must be made by the appropriate division standards activity in writing tothe Manufacturing Staff. All supporting data must accompany the writtenrequest. Manufacturing Staff, Environmental Health and Safety Manager,and Employee Relations Staff, will review request for approval.