FORD SB3-2-1988 COVERALLS - FLAME RETARDANT《阻燃工作服》.pdf

1、 Manufacturing StandardsFord Motor Company198807 COVERALLS - FLAME SB3-2RETARDANTEngineering Standards Collar, 17 inches (432mm); Sleeve (inseam), 20-3/4 inches(527mm); Sleeve (outseam) 34-3/4 inches (883mm); Trunk Length, 76-3/4inches (1947mm); Leg (inseam), 32-1/2 inches (826mm); Waist (snapped),

2、46inches (1168mm); Seat, 54 inches (1372mm); Thigh, 34 inches (864mm);Knee, 25-1/2 inches (648mm); and Leg Bottom, 21-1/4 inches (546mm).Measurements for all other sized coveralls shall be proportioned to theabove. Measurements listed are typical and may vary slightly withvarious manufacturers. All

3、garments shall have long sleeves. Garmentsshall be green.4. REQUIREMENTS:4.1 SIZE RANGE:Small 38)Medium 42)Large 46) Standard NumberX Large 50)XX Large 54) SB3-16 - SizeXXX Large 58)XXXX Large 62)4.2 MATERIAL REQUIREMENTS:a. 100% cotton sateen finished from 51-1/2 inches (1308mm) (- 80 x48 - thread

4、size - 1.35 yard or heavier. This is an 80 x 48sateen in 8.25 oz. (234 g.) to 8.50 oz. (241 g.) square yard ifpreshrunk only and not sized. Finished FR weight to be 9.0 oz.(255 g.) to 9.5 oz. (269 g.).Manufacturing StandardsFord Motor Company198807 COVERALLS - FLAME SB3-2RETARDANTEngineering Standar

5、ds & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 2 of 3b. 100% cotton twill in 108 x 56 count type 4 twill. This is a 108x 56 count type 4 twill in 8.5 oz (241 g.) square yard ifpreshrunk only and not sized.c. Snap fasteners shall be designed to last the life of the garmentand sh

6、all be stainless steel. All are to be done with No. 30(heavy) cotton thread.4.3 FINISH: Either THPOH-NH3 or “Ammonia Cure“ flame retardant finishshall be used. Treated material shall not cause skin irritation orbe toxic to the wearer.4.4 FLAME RESISTANT - FLAME RETARDANT (FEDERAL TEST METHOD: 191:59

7、03):NOTE: Coverall material shall be treated with life of garment flameresistance process. Treated material shall not cause skinirritation or be toxic to the wearer. Material after the flameretardant treatment shall not become stiff or rough. Flameretardant treatment must be durable and last the nor

8、mal life of thegarment and shall not lose effectiveness after 25 industrial washcycles. Coveralls must be machine washed and tumble dryed. Use nochlorine bleach.4.5 CONSTRUCTION: Concealed fly front shall have six snap fasteners.One exposed fastener shall be at the lapel collar. Coveralls tohave two

9、 patch chest pocket, two patch hip pockets, two inside orswing with side openings for access to trouser pockets. doubleturned bottom hem. All hems to be rolled and single chain stitched.All seams to be double needle felled and either double lock ortriple chain stitched. Bar tack all strain points. B

10、louse to bejoined to trouser parts with four needle, 401 stitch, 1-1/2 inchouter needle guage, 1 inch inner needle guage, which is to becovered on outside with garment material band 1-7/8 inches (48mm)wide edges turned and joined with four rows of stitching 1-3/4 inchfinished. Sleeve cuffs construct

11、ed cut on and finished with singleneedle 301 stitch, fake stitch construction. Concealed gripperclosure. Cuff vent opening is 3-1/2 inch by 4 inch from bottom ofcuff to bartack. Collar to be lapel type, set and finished withsingle needle 301 stitch, 1/8 inch seam margin.4.6 SHRINKAGE: American Natio

12、nal Standard test method ASTM D2724-79shall be used.5. MANUFACTURERS IDENTIFICATION: Each garment shall have a manufacturersidentification label located inside the back below the collar showingFord Standard number, garment number, date of manufacture, and the words“Flame Retardant“. This label shall

13、 be 1-1/8 inches (29mm) x 3-3/4inches (95mm) color orange with permanent black ink printed lettering andshall not discolor when laundered for life of garment. The flameretardant lettering shall be not less than 1/4 inch (6mm) in size. Thegarment size lettering shall be not less than 3/16 inch (5mm)

14、in size.Manufacturing StandardsFord Motor Company198807 COVERALLS - FLAME SB3-2RETARDANTEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 3 of 35.1 SAMPLE LABEL:LARGE 100% COTTONF L A M E R E T A R D A N TSB3-16 DATE OF MFG. GARMENT NO.MACHINE WASH - TUMBLE DRYU

15、SE NO CHLORINE BLEACH6. SAMPLING PROCEDURE: A random sample of each lot of new garments shall beselected and forwarded to Central Laboratory Services for testing inaccordance with this standard. Failure of any sample or any test shallbe sufficient cause to reject the lot represented by the sample.Pe

16、riodically, a garment that has been used and washed many times will beselected and forwarded to Central Laboratory Services for testing.Failure to meet Paragraph 4.4 shall be sufficient reason for rejection ofthe manufacturer as a supplier. The laboratory reports will be forwardedto the Plant Engine

17、ering Evaluation and Standards Office, ManufacturingStaff, and Corporate Safety Manager, Personnel and Organization Staff.7. SUPPLIERS RESPONSIBILITY: All garments supplied to this standardmust be equivalent in all characteristics to the garments upon whichapproval was originally granted and shall b

18、e satisfactory for theintended application.8. APPROVAL OF THE NEW SUPPLIERS: Garments submitted by the newmanufacturers to this standard must have purchasing source approval andlaboratory and shop trials approvals. Recommendations for the additionof new manufacturers to the Manufacturing Approved So

19、urce List must bemade by the appropriate Division Standards Activity in writing to PlantEngineering Office. All supporting data must accompany the writtenrequest. The Plant Engineering Office, Manufacturing Staff, and theEnvironmental Health and Safety Manager, Employee Relations Staff, willreview r

20、equests for approval.9. PACKAGING INSTRUCTIONS: Garments shall be packed twenty-four (24) percarton, solid sizes. Each carton shall be labeled or stenciled at bothends with the following information:Sellers nameBlanket order numberRelease numberStandard or code number and sizeQuantity in pieces or pairsRequisitioners name and location9.1 CARTON SIZE: 21-3/4 inches (553mm) long x 14 inches (356mm) wide x26 inches (660mm) high. Bursting test of carton - 275 lbs (125 kg).