ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:169.46KB ,
资源ID:748244      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-748244.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD SS-M99G9514-A-2006 NOISE INSULATION SHIELD-I《隔噪屏障-I》.pdf)为本站会员(postpastor181)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD SS-M99G9514-A-2006 NOISE INSULATION SHIELD-I《隔噪屏障-I》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2006 10 18 Revised Inserted 3.0; Deleted 3.10 specimens of 50 x 50 mm to be cut from plane areas of finished part) 3.2 THICKNESS 6.0 +/- 1.5 mm or as specified (Slide gauge) on Engineering drawing 3.3 WATER ABSORPTION, max 60% Test Method: 1)

2、 Cut 50 x 50 mm specimens from plane areas of finished part. 2) Seal edges of test specimens against test fluid penetration (e.g use wax). 3) Weigh specimens nearest to 0.1 g. 4) Immerse at room temperature in distilled water for 24 hours. 5) Slightly blot specimens with filter paper to remove exces

3、sive test fluid from the surfaces of specimens. 6) Weigh specimens again nearest to 0.1 g and calculate the increase of weight in % based on original value. ENGINEERING MATERIAL SPECIFICATION SS-M99G9514-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 5 3.4

4、COLD IMPACT RESISTANCE No cracking Test Method: 1) Place a steel ball of 30 mm diameter, mass 225 g, and a 50 x 50 mm specimen, cut from plane areas of finished part for 4 hours at -40 +/- 2 C in a cold box. 2) Place the specimen horizontally on a base plate and normal to the direction of impact. 3)

5、 While still in the cold box drop the steel ball to the middle of the specimen from a height of 1000 mm. 3.5 TENSILE STRENGTH (ASTM D 412, Die C; specimens to be cut from plane areas of finished part) 3.5.1 Original, min 175 N/cm2 3.5.2 After Humidity Ageing, max -15% (48 h at 38 +/- 2 C and 98 +/-

6、2% relative humidity) 3.5.3 After Heat Ageing No loss (14 d at 90 +/- 2 C, 1 h at room temperature) 3.5.4 After Immersion in Engine Oil, max -15% (48 h in Oil No. 1 of ASTM D 471 at room temperature) 3.5.5 After Immersion in Water, max -15% (48 h in distilled water at room temperature) 3.6 TEAR STRE

7、NGTH, min 220 N/cm (ASTM D 624, Die C; specimens to be cut from plane areas of finished part) 3.7 FINISHED PART REQUIREMENTS 3.7.1 Dimensions As specified on Engineering drawing 3.7.2 Mass The tolerance in mass of finished part for any one supplier shall be maximum +/- 10%, based on the recorded mas

8、s of his originally approved sample. ENGINEERING MATERIAL SPECIFICATION SS-M99G9514-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 5 3.7.3 Heat Stability The finished part shall show no evidence of delamination, no visible shrinkage or distortion, respectiv

9、ely it shall not warp to an extent that would affect its use in ultimate assembly. Furthermore, it shall show no change in appearance when compared with the original unaged part. Test Method: The finished part shall be subjected to a temperature of 90 +/- 2 C in a mechanically convection air dry ove

10、n for 24 hours. Examine after cooling to room temperature. 3.7.4 Environmental Cycling The finished part shall show no evidence of delamination, no visible shrinkage or distortion respectively, it shall not warp to an extent that would affect its use in ultimate assembly. Furthermore, it shall show

11、no change in appearance when compared with the original un-aged part. Test Method: T he finished part shall be subjected 3 times to the following cycle in the sequence indicated below: 16 h at 38 +/- 2 C and 98 +/- 2% relative humidity 8 h at 80 +/- 2 C 3 h at -40 +/- 2 C Examine after cooling to ro

12、om temperature. 3.7.5 Cold Resistance after Ageing No cracking. Test Method: 1) Expose the finished part to 90 +/- 2 C for 120 hour. 2) After cooling to room temperature store the part and a steel ball of 30 mm in dia and 225 g for 4 hours at -40 +/- 2 C in a cold box. 3) Place the test specimen par

13、t horizontally on a base plate and normal to the direction of impact. 4) While still in the cold box drop the steel ball to the middle of the test part from a height of 1000 mm. 3.7.6 Moisture Absorption, max 20% Test Method: 1) Weigh finished part nearest to 5 g. 2) Condition the part in suspended

14、position at 98 +/- 2% relative humidity and 38 +/- 2 C for 24 hours. ENGINEERING MATERIAL SPECIFICATION SS-M99G9514-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 4 of 5 3) After 1 hour at room temperature weigh the part nearest to 5 g and determine increase of

15、weight in percentage based on original weight. 3.7.7 Mildew Resistance The material shall be free from mildew and malodor. There shall be no visible changes evident after drying. Test Method: 1) Cut from finished part a piece of 50 x 50 mm and soak with distilled water. 2) Place test piece in a beak

16、er glass of one liter capacity, and cover tightly with a lid. Store at 35 +/- 2 C for 14 days. 3.7.8 Resistance of Coating to Various Test Reagents The finished part shall not dissolve, exhibit tackiness or delaminate when rubbed lightly for 15 seconds with a cotton cloth soaked with each of the fol

17、lowing test reagents. Use a separate specimen for each test reagent. Test Reagents: 1) Oil No.1 of ASTM D 471 2) Brake fluid, SA-M1C9101-A 3) Sulphuric acid (10% by weight in distilled water) 4) Longlife coolant SS-M97B9101-A (50% by weight in distilled water) 5) Rust preventive compound SK-M7C9552-

18、A 3.8 INSULATING PROPERTIES (See Figure 1) Test Method: 1) FLTM EU-BV 60-4, except use metal panel of 1 kg/m2. 2) For measuring, un-molded plane samples of 300 x 300 mm shall be used. For thickness see Figure 1. Note: If the finished part does not allow the preparation of plane specimens as required

19、 above, the supplier is required to provide, together with the Initial Sample Report, specimens of same material and equivalent manufacture used for the finished part. Samples for control and routine checks shall be submitted as required by Quality Control. ENGINEERING MATERIAL SPECIFICATION SS-M99G

20、9514-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 5 of 5 3.9 HEALTH HAZARDS AND ODOR The material must not contain any ingredients (matter), which, under normal production conditions, could lead to health hazards such as skin rash or irritation (dermatitis), irritation of the mucous membranes, difficulties in breathing, etc. The material shall be free from objectionable odors both as received and after storage.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1