FORD WSB-M29G1-B-1992 EDGEWORK REQUIREMENTS AUTOMOTIVE SAFETY GLASS《汽车安全玻璃的磨边要求》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Release/Revision1992 01 31 NB00I10043054150 Released TRB R.D. Moore LWMWP 3948-a Page 1 of 4 EDGEWORK REQUIREMENTS, AUTOMOTIVE SAFETY GLASS LWSB-M29G1-B1. SCOPEThi s specification defines the basic requirements for

2、 automotive safetyglass edgework, including definitions, manufacturing imperfections, anddimensions.2. APPLICATIONTh is specification was released originally for edgework requirements forsafety glass used in glazing motor vehicles. Edges shall be treated inac cordance with SAE recommended Practice J

3、673a, “Automotive Glazing“,August 1967, which is incorpora ted by reference in FMVSS 205, February 23,1984.3. REQUIREMENTS3.1 STATISTICAL PROCESSSupplie rs must conform to the requirements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for m

4、aterial/source approval. Appropriatestatist ical tools must be used to analyze process/product data sothat variation in the final product is continuously reduced.3.2 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on ma terial conditioned ina control led atmosphere of 23 +

5、/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested under thesame conditions unless otherwise specified.L3.3 TYPE 1 CROWN, SEMI-SATIN FINISH EDGEDen otes radius as indicated, fine ground to a semi-satin finishhaving smooth even surface without luster. Typi cal f

6、or exposed edgessuch as on ventilators, door lights, and quarter lights. Must conformto SA E J673a, Edge No. 1 Occasional flake chips 1.6 mm diameterpermitted (edge or crown). Occasional shiners 3 .2 mm diameter or 1.6mm wide by 13 mm long permitted.Minimum radius 1/2 glass thicknessMaximum radius a

7、pproximately 6 mmENGINEERING MATERIAL SPECIFICATIONLWSB-M29G1-BWP 3948-b Page 2 of 4 3.4 TYPE 2 CROWN, SEMI-SATIN FINISH EDGESimilar to Type 1, except the arc of the grind m ay have gaps anywherealo ng the edge, where the central portion of the edge is below thegeneral contour. These gaps are known

8、as “shine rs“. Flake chips mayalso occur. Overlap or slip is permissible on these edges not toexceed 0 .8 mm. These edges are characteristic of edges which areconcealed but intended to slide in guides as vertical edges of doorlights, body lights, etc.Minimum radius 1/2 glass thicknessMaximum radius

9、approximately 6 mm3.5 TYPE 3 SEAMED (CHAMFERED) EDGEDe notes original edge ground off as indicated. Flake chips andshiners permitted. Overlap of 0.8 mm permitted on flat glass, 1.6 mmpermitted on curved windshields only. Typical for framed laminatedglass and all heat treated safety float glass. Viny

10、l expulsion of0.76 mm maximum is permissible.3.6 TYPE 4 CLEAN CUT EDGEDenotes no further work on edges after laminating except removal ofex cess vinyl. Vinyl expulsion of 0.76 mm maximum is permissible.Flake chips which are not visible after glass is installed and do notmaterially affect strength of

11、 glass are permitte d. Overlap of 0.8 mmpermitted on flat body glass, 1.6 mm permitted on curved windshieldsonly. Typical for glass enclosed in frmae or se aled in body opening.ENGINEERING MATERIAL SPECIFICATIONLWSB-M29G1-BWP 3948-b Page 3 of 4 3.7 TYPE 5 CLEAN CUT EDGEDenotes no further work on edg

12、es after laminatin g. Flake chips whichare not visible after glass is installed and do not materially affectstrength of glass are permitted. Overlap of 0.8 mm permitted on flatbody glass, 1.6 mm perm itted on curved windshield only. Typical forglass enclosed in frame or sealed in body opening.Glass

13、manufacturers are not required to furnish a true radius on any edgewhere a radius is specified.The blu eprint shall show the minimum quality edge types only. Any typesuperior to that specified can be used.3.8 ADDITIONAL REQUIREMENTSSpecific requirements for material and/or manufa ctured parts shall

14、bespecified on the Engineering drawing, Engineerin g parts specificationand/or performance specifications. All critical areas with respect tothese properties shall be clearly designated on the engineeringdrawing.3.9 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equival

15、ent inal l characteristics to the material upon which approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials

16、ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be

17、 submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WS S-M99P9999-A1, unlessa different suffix (e.g., A2 or A3) is specified on the engineeringdocum

18、ent for the application.ENGINEERING MATERIAL SPECIFICATIONLWSB-M29G1-BWP 3948-b Page 4 of 4 4. APPROVAL OF MATERIALSThis specification is intended to define the performance and/or propertiesof finished parts or systems of combined materials. An E ngineering MaterialApproved Source listing is not applicable for this specification. ProductEngin eering materials referenced in this document and/or the affecteden gineering drawing, which require prior Engineering approval, are shownin the Engineering Material Approved Source List under the specificationcited.