FORD WSB-M7H47-B-2010 WEBBING POLYESTER UNEVEN NINE-PANEL SAFETY BELT TO BE USED WITH FORD WSS-M99P1111-A 《安全带用板式不均匀NINE-PANEL聚酯织物带 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 Date Action Changes 2010 03 04 N-STATUS No replacement named L. Sinclair, NA 1991 09 10 NB00I10043054124 Released D.Henrickson B.Ferns L.Moriarty WP 3948-a Page 1 of 5 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number WEBBING, POLYESTER, UNEVEN NINE-PANEL, SAFETY WSB-M7H47-B BEL

2、T NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a polyester seat belt webbing woven with continuous filament yarn and finished selvages. Proper dyes and dyeing procedures shall be employed to provide acceptable colors, appearance, and physical properties. Color

3、 stripping for redyeing of webbing rejected for color is not allowed. The webbing shall be of good quality and uniform construction. 2. APPLICATION This specification was released originally for material used for metal to metal type seat belts on 1993 vehicles. 3. REQUIREMENTS Test Method Procedures

4、: All webbing properties denoted by shall be tested in accordance with Federal Motor Vehicle Safety Standard No. 209. DE requirements listed in any of the following paragraphs are intended as maximum target values. Visual ratings will take precedence. 3.1 STATISTICAL PROCESS Suppliers must conform t

5、o the requirements of Ford Quality System Standard Q-101. A mutually acceptable Control Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.2 C

6、ONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 48 - 67 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. 3.3 APPEARANCE (FLTM BI

7、 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. ENGINEERING MATERIAL SPECIFICATION WSB-M7H47-B WP 3948-b Page 2 of 5 Note: This webbing is to be manufactured in an “uneven“ nine panel weave constructio

8、n (not including the edges as panels). 3.4 THICKNESS 1.19 +/- 0.05 mm (SAE J882) 3.5 WIDTH Measured at less than 22 N load 3.5.1, min 46.25 mm 3.5.2, max 48.0 mm Measured at 9 790 N load 3.5.3, min 46.25 mm 3.6 COMPOSITION (ASTM D 629) Polyester 100 % 3.7 WEIGHT, min 5.5 kg/100 m 3.8 BREAKING STRENG

9、TH, min 27 140 N 3.9 ELONGATION, max 8 % at 11 120 N 3.10 RESISTANCE TO LIGHT, min 87 % of original (Retained breaking strength after 100 breaking strength weatherometer hours exposure without water spray) 3.11 RESISTANCE TO HEX BAR ABRASION, min 77 % of original (Retained breaking strength after 5

10、000 breaking strength abrasion strokes - 2 500 cycles) 3.12 RESISTANCE TO BUCKLE ABRASION, min 20 560 N (Retained breaking strength after 5 000 abrasion strokes - 2 500 cycles) 3.13 RESISTANCE TO FADE (AATCC Evaluation Procedure 1) 3.13.1 Weatherometer, min (max) Rating 3 (3.4 DE) (100 h without wat

11、er spray) 3.13.2 Xenon Arc, min (max) Rating 3 (3.4 DE) (SAE J1885, 225.6 kJ/m2) No individual yarn or combination of yarns shall fade, stain or exhibit any color tone change, nor shall the yarns change in hue or brightness in excess of the above ratings. 3.14 COLORFASTNESS TO CROCKING, WET AND DRY,

12、 min (max) Rating 4 (4.3.DE) Note: Instrumental reading to be determined per FLTM BN 107-02, AATCC Evaluation Procedure 2. ENGINEERING MATERIAL SPECIFICATION WSB-M7H47-B WP 3948-b Page 3 of 5 ENGINEERING MATERIAL SPECIFICATION WSB-M7H47-B WP 3948-b Page 4 of 5 3.15 COLORFASTNESS TO STAINING-BLEEDING

13、, min (max) Rating 4 (4.3 DE) (FLTM AN 101-01, AATCC Evaluation Procedure 2) 3.16 PERSPIRATION, min (max) Rating 4.5 (FLTM AN 101-01, AATCC Evaluation Procedure 2) (2.2 DE) 3.17 SPOTTING, min (max) (FLTM AN 101-01, AATCC Evaluation Procedure 2) 3.17.1 All colors - Water Rating 5 (1.8 DE) 3.17.2 For

14、Light Colors Only Coffee Rating 5 (1.8 DE) Soap Solution (25 % Lux or equivalent) Rating 5 (1.8 DE) Motor Oil (SAE 30 W) Rating 5 (1.8 DE) Colors designated light or mutually agreed to by the supplier and Body Engineering must meet this spotting requirement. 3.18 SOILING AND CLEANABILITY, max (FLTM

15、BN 112-04, light colors only) Soiling Loss in Reflection 38 % Cleanability Loss in Reflection 28 % Future color selections designated light or mutually agreed to by the supplier and Body Engineering, must also meet this soiling requirement. 3.19 STIFFNESS (ASTM D 747, 25 x 50 mm sample, 12.7 mm span

16、) 3.19.1 Lateral (fill) direction, min 0.5 N (0.034 N-m moment, ave. of 6 tests) 3.19.2 Longitudinal (warp) direction, max 1.8 N (0.113 N-m moment, ave. of 6 tests) Sample preparation: Die-cut 6 samples (25 x 50 mm) in each direction. For each direction, the stiffness is determined on both sides (3

17、samples per side). . Pre-load sample to 1 % full-scale load with hand crank . Zero the angular scale and start test . Read the load scale at 45 deg deflection and subtract the 1 unit preload . Record the result . Repeat for each sample ENGINEERING MATERIAL SPECIFICATION WSB-M7H47-B WP 3948-b Page 5

18、of 5 Stiffness computation: . Lateral - 2.67 x Load Scale Reading - 100 . Longitudinal - 8.90 x Load Scale Reading - 100 3.20 FOGGING (Initial certification only for each color) (FLTM BO 116-03) Fog Number, min 60 The formation of droplets or coalescence into a clear film is cause for rejection. 3.2

19、1 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute 3.22 ADDITIONAL REQUIREMENTS Specific requirements for material and or manufactured parts shall be specified on the engineering drawing, Engineering parts specification and/or performance specifications. All critical areas with respect

20、to these properties shall be designated on the Engineering drawing. 3.23 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes in the properties, composit

21、ion, construction, color, processing or labeling of the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering acti

22、vity of the proposed changes and obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Substance restrictions imposed by law, regulations or Ford apply to the materials addressed by this document

23、. The restrictions are defined in Engineering Material specification WSS-M99P9999-A1, unless a different suffix (e.g., A2 or A3) is specified on the engineering document for the application. ENGINEERING MATERIAL SPECIFICATION WSB-M7H47-B WP 3948-b Page 6 of 5 4. APPROVAL OF MATERIALS Materials defin

24、ed by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affected Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall s

25、ubmit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification (test results, not nominal values), the mate

26、rial designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessment of suitability for intended processes and/or applications. Upon approval, the material will be added to the E

27、ngineering Material Approved Source List. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 INSTRUMENTED COLOR READINGS The instrument used for color difference measurements shall be either a spectrophotometer or a tristimulus colorimeter, and shall be capable of providing the following: Geometry 0/45 Observer 10 degree Specular Reflectance In (if an option) Illuminant D 65 Sample port size 25 mm (unless specified otherwise in test method)