ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:46.27KB ,
资源ID:750022      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-750022.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD WSE-M1A172-B3-2013 NODULAR IRON MEDIUM TO HIGH STRENGTH TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSE-M1A172-B1).pdf)为本站会员(tireattitude366)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD WSE-M1A172-B3-2013 NODULAR IRON MEDIUM TO HIGH STRENGTH TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSE-M1A172-B1).pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 3 2013 03 07 Revised Revised 3.4 G. Weber, FNA 2002 07 30 Revised Updated and renumbered 1987 10 28 SM/ER1249TC Released - H. Nikkel NAAO, N P Riley, EAO Controlled document at www.MATS Copyright 2013, Ford Global Technologies, Inc. Page

2、 1 of 3 NODULAR IRON, MEDIUM TO HIGH STRENGTH WSE-M1A172-B1/B2/B3/B4 1. SCOPE The material defined by this specification is a nodular iron. 2. APPLICATION This specification was released originally for material used for crankshafts. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS

3、Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 CHEMICAL COMPOSITION (LADLE) Specific chemistry will vary based on section size and foundry practice to achieve the required mechanical properties. The ladle analys

4、is will form part of the control plan. 3.3 HARDNESS 3.3.1 As cast hardness - Determined between foundry and machinist. 3.3.2 Bearing and seal running Surface Hardness, HB B1 B2 B3 B4 (ISO 6506/ASTM E10) 217-286 235-302 255-311 302-359 Unless otherwise specified, castings may be normalized or anneale

5、d to meet the desired hardness range. Grade B4 shall be oil hardened and tempered. ENGINEERING MATERIAL SPECIFICATION WSE-M1A172-B1/B2/B3/B4 Page 2 of 3 Copyright 2013, Ford Global Technologies, Inc. 3.4 MECHANICAL PROPERTIES (ISO 6892/ASTM E8M) B1 B2 B3 B4 3.4.1 Tensile Strength, MPa, min 560 630 7

6、00 900 3.4.2 Yield Strength, MPa, min 350 400 450 600 (0.2 % offset) 3.4.3 Elongation, %, min 2 2 2 2 Mechanical properties shall be measured on test specimens taken from parts produced according to the approved Control Plan. The test specimen and Brinell hardness location shall be indicated on the

7、appropriate Engineering Drawing and/or Engineering Specification, and reflected in the Supplier Control Plan. Tests may be carried out on substandard test specimens if standard specimens cannot be obtained. 3.5 MICROSTRUCTURE - Finished Component Before Fillet Rolling When viewed at 100x critical ar

8、eas shall consist of: B1 B2 B3 B4 Tempered Martensite, %, min - - - Complete transformation Pearlite, %, min 50 80 90 - Ferrite, %, max 50 20 10 1 Retained Austenite, %, max - - - 15 Free Carbide, %, max 1 1 1 1 Graphite Form, %, min 75 90 90 90 (ASTM A 247 Type I & II) Graphite Size: (ASTM A 247) T

9、he graphite shall be predominantly size 5, 6 & 7, size 4 nodules shall not exceed 5 %, the nodule distribution shall be uniform, random and free from agglomeration and flotation. Note: Critical areas (eg bearing surfaces, fillet radii,etc.) to be specified by Engineering. Other control locations may

10、 be employed provided the finished part microstructure is maintained. ENGINEERING MATERIAL SPECIFICATION WSE-M1A172-B1/B2/B3/B4 Page 3 of 3 Copyright 2013, Ford Global Technologies, Inc. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the re

11、quirements of the specification. Contact for questions concerning Engineering Material Specifications. 4.1 MODULUS OF ELASTICITY 150 GPa 4.2 MICROSTRUCTURE (In-Process) For components requiring subsequent surface hardening, in-process controls should be introduced so that the ferrite levels are bel

12、ow 10 % on the bearing surfaces prior to hardening. This may be achieved by normalizing. 5. SUMMARY OF REVISIONS 2013 03 07 Revised tensile specimen location for Mechanical Properties in para 3.4. 2002 07 30 Revised Updated and renumbered 1994 06 22 Revised Title, 3.5, 3.5 G. Lane EAO P. Lee NAAO, NE01-E-10127076-132

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1