ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:30.87KB ,
资源ID:750302      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-750302.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD WSK-M11P57-A3-2009 PERFORMANCE STRUCT ADHESIVE 1 COMP PUR FAST FIX TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M11P57-A1)《快速安装型聚氨酯(PUR)单组分结构胶粘剂的性能 与标准FORD WSS-M.pdf)为本站会员(towelfact221)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD WSK-M11P57-A3-2009 PERFORMANCE STRUCT ADHESIVE 1 COMP PUR FAST FIX TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M11P57-A1)《快速安装型聚氨酯(PUR)单组分结构胶粘剂的性能 与标准FORD WSS-M.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 01 07 N-STATUS Replaced by WSS-M11P57-A5 M. Mehandru, FNA 1994 07 08 EP00E10422649000 Released B. Lange WP 3948-a Page 1 of 7 PERFORMANCE, STRUCT, ADHESIVE; 1 COMP., PUR; STANDARD WSK-M11P57-A1 PERFORMANC

2、E, STRUCT, ADHESIVE; 1 COMP., PUR; HIGH MODULUS WSK-M11P57-A2 PERFORMANCE, STRUCT, ADHESIVE; 1 COMP., PUR; FAST FIX WSK-M11P57-A3 PERFORMANCE, STRUCT, ADHESIVE; 1 COMP., PUR; NON CONDUCTIVE WSK-M11P57-A4 NOT TO BE USED FOR NEW DESIGN 1. SCOPE These specifications define the performance requirements

3、for solvent free, polyurethane based, structural metal-to-metal respectively semistructural metal-to-glass adhesives as follows (see also 5.1) WSK-M11P57-A1: One component material and moisture curing at ambient temperatures, with standard fix behavior, WSK-M11P57-A2: One component material and mois

4、ture curing at ambient temperatures with a high shear modulus behaviour after complete curing, WSK-M11P57-A3: One component material, warm bead applied and moisture curing at ambient temperatures, with a fast fix behaviour, WSK-M11P57-A4: One component material and moisture curing at ambient tempera

5、tures, with standard fix and non conductive behaviour. 2. APPLICATION The specifications WSK-M11P57-A1, -A2, -A3, -A4 were released originally to provide life time semistructural bonding of windshields, backlights and quarter windows in connection with adhesion promoter and adhesion primer for glass

6、 or for bonding painted parts without any adhesion promoter or primer. 3. REQUIREMENTS 3.1 STATISTICAL PROCESS Suppliers must conform to the requirements of Ford Quality System Standard Q-101. A mutually acceptable Control Plan as described therein is required for material/source approval. Appropria

7、te statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.2 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative h

8、umidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 2 of 7 3.3 SYSTEMS COMPONENTS 3.3.1 Substrates and Compatability The adhesive must be compatable with all related

9、materials, e.g. top coat, clear coat, glass, ceramic ink, polyurethane, EC, primer surfacer, etc. or as specified on Engineering Drawing. Note: If any other substrate gets relevant for manufacturing, the adhesive has to be tested according to this specification on this substrate. The adhesive suppli

10、er must certify compliance to all requirements of relevant adhesive and/or performance specification (test values, not nominal values). 3.4 PERFORMANCE PROPERTIES 3.4.1 Green Strength, min WSK-M11P57-A1, -A2, -A4: 0.1 MPa (FLTM BV 154-03) WSK-M11P57-A3: 0.4 MPa Test Method . Prepare test specimens (

11、see section 3.3.1 of specification) according to section B, para 1 & 2 of FLTM BV 154-03. . Cure test specimens for 3 h at 23 +/- 2 C and 50 +/- 5 % r.h. . Determine shear strength according to Method B of FLTM BV 154-03. 3.4.2 Shrinkage After Curing, max 5 % Test Method: . Apply to a release paper

12、two beads of material under test in dimensions of 50 x 8 x 5 mm and determine exact volume by water displacement method immediately after material application. . Age test samples at 80 +/- 2 C for 14 days. . Determine exact volume of material under test once again and calculate volume shrinkage. 3.5

13、 SHEAR STRENGTH, min 2.5 MPa (except 3.5.1: at 90 +/- 2 C except 3.5.8: 2.5 MPa accepted if paint delamination occures) ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 3 of 7 Test Method . Test panels are to be prepared for the tests according to FLTM BV 103-02, B, using pro

14、duction as well as repair enamel. . Dimension of test specimens: 80 x 30 x 4 mm heat treated safety glass (DELTA WSK-M28G21/22-A) with ceramic coating (DELTA WSK-M99G109-D/E/F) and 80 x 30 x 5 mm laminated safety glass (DELTA WSK-M28G23-A) with ceramic (DELTA WSB-M99G109-D/E/F) or safety glass coate

15、d with polyurethane according to WSD-M2D404-A1/A2. Body steel specimens: 100 x 25 x 1.3 (+/- 0.5 mm). . Clean ceramic surface of glass specimen using adhesion promoter WSK-M2G342-A and wipe off with a clean and dry cloth. . After 5 minutes conditioning at 23 +/- 2 C prime glass bonding surface with

16、primer according to WSK-M2G343-A respectively WSK-M2G377-A1. Condition for 5 minutes at 23 +/- 2 C. . Apply adhesive to painted surface. After 5 minutes at 23 +/- 2 C assemble with adhesion promoter cleaned glass or primed polyurethane specimen according to Figure 1 to reach a right angled bead form

17、 of 5 x 8 mm. . Allow adhesive to cure for 7 d at standard atmosphere (23/50). . Determine shear strength at a speed of testing of 25 mm/minute. A minimum of 5 specimens shall be tested and the average result shall conform to the requirement specified above. Note: In case of laminated glass failure

18、before reaching minimum shear strength requirement, the test is to be rated as satisfactory and the result noted in the report, if no adhesion failure occurred, proceed similar in case of delamination of paint layers. 3.5.1 Original Measured at 90 +/- 2 C*, min 1.5 MPa Measured at 23 +/- 2 C Measure

19、d at - 40 +/- 1 C* * 30 minutes tempering time until measuring 3.5.2 After Heat Aging 14 days at 90 +/- 2 C, 1 hour at 23 +/- 2 C 3.5.3 Florida Exposure Test Method: Specimens prepared according to 3.4 shall be exposed in the Miami Florida area for 1 year with the glass facing the light at 5 degrees

20、 south. The glass shall be cleaned with distilled water once a month. ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 4 of 7 3.5.4 After UV-Exposure Test Method: . Expose test assemblies with glass facing the light source per SAE J1960 at a) 1570 kJ/m2 and b) 3920 kJ/m2 or a

21、lternatively per SAE J2019 at c) 171130 kJ/m2 and d) 427280 kJ/m2. . Determine shear strength after 1 h at 23 +/- 2 C. Note: In case of differences between the results of Florida exposure and accelerated weathering, the Florida results are relevant. 3.5.5 After Water Immersion 240 hour immersion in

22、distilled water at 38 +/- 2 C, 5 minutes at 23 +/- 2 C. 3.5.6 After Humidity Aging 14 days at 38 +/- 2 C and 98 +/- 2 % RH, 1 hour at 23 +/- 2 C. 3.5.7 After Environmental Cycling Test Method: Samples must be exposed four times to the following cycle in the sequence indicated below: 16 hours at 38 +

23、/- 2 C and 98 +/- 2 % RH 4 hours at minus 40 +/- 1 C 4 hours at 80 +/- 2 C After four cycles specimens to be stored at 23 +/- 2 C for 72 hours before testing. 3.5.8 After Cataplasma test Test Method: . Test specimens to be wrapped with hydrophilic cotton patting and 5 each to be put into sealed cont

24、ainers of approximately 160 ml volume space with 100 ml distilled water to provide constant conditions for following storage: ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 5 of 7 14 days at 70 +/- 2 C 2 hours at - 20 +/- 2 C 2 hours at 23 +/- 2 C . Remove wet cotton and te

25、st shear strength within 2 hours. 3.5.9 Resistance to Anti Freeze Solution Test Method: Use test specimens, 1 hour curing time, immerse in a solution consisting of 50 volume % isopropyl alcohol and 50 volume % distilled water for 5 minutes and test after a curing time of 14 days at 23/50 standard at

26、mosphere. 3.6 SHEAR MODULUS, +/- 15 % WSK-M11P57-A1, -A4: 1.1 MPa (Similar to DIN 53283, test WSK-M11P57-A2: 2.5 MPa samples see Fig.2, test speed WSK-M11P57-A3: 1.8 MPa 10 mm/minute) 3.6.1 Original For test Conditions see 3.5.1 3.6.2 After Heat Aging: For test Conditions see 3.5.2 3.6.3 After Humid

27、ity Aging: For test Conditions see 3.5.6 3.6.4 After Cataplasma Test: For test Conditions see 3.5.4 3.7 ELECTRICAL CONDUCTIVITY, Ohm cm, min WSK-M11P57-A1,-A2,-A3: 10xE4 (DIN 53482) WSK-M11P57-A4: 10xE10 3.7.1 Original: For test Conditions see 3.5.1 3.7.2 After Humidity Aging: For test Conditions se

28、e 3.5.6 3.8 90 DEGREE PEEL ADHESION cohesion failure Test Method: . Apply a bead of material under test, 250 mm in length, in a triangel form, 8 mm base and 100 mm height, to a freshly painted panel (or other relevant surfaces, see 3.3.1) and cover with release paper, press adhesive bead to a thickn

29、ess of approximately 4 mm for whole length and remove release paper after 24 hours. . Allow adhesive to cure for 7 days at standard atmosphere (23/50). . Peel-off adhesive bead from panel in a length of 50 mm from one end by using a clamp and giving a start the first few mm length by cutting-in and

30、lifting from the panel and evaluate for type of failure. . Continue testing of specimen by heat ageing at conditions according to 3.5.2. ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 6 of 7 . Peel-off adhesive bead from panel in a length of another 50 mm and evaluate for t

31、ype of failure. . Continue testing of specimen by environmental cycling at conditions according to 3.5.7. . Peel-of adhesive bead from panel in a length of another 50 mm and evaluate for type of failure. . Continue with cataplasma test at conditions according to 3.5.8. . Peel-off adhesive bead from

32、panel in a length of another 50 mm and evaluate for type of failure. 3.9 ADDITIONAL REQUIREMENTS Specific requirements for material and/or manufactured parts shall be specified on the Engineering drawing, Engineering parts specification and/or performance specification. All critical areas with respe

33、ct to these properties shall be clearly designated on the engineering drawing. 3.10 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any change in the properties

34、, composition, construction, color, processing or labeling of the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engine

35、ering activity of the proposed changes and obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Substance restrictions imposed by law, regulations or Ford, apply to the materials addressed by th

36、is document. The restrictions are defined in Engineering Materials Specification WSS-M99P9999-A1. ENGINEERING MATERIAL SPECIFICATION WSK-M11P57-A1/A2/A3/A4 WP 3948-b Page 7 of 7 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Eng

37、ineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affected Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their lab

38、oratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords en

39、gineering approval of a material will be based on its performance to this specification and on an assessment of suitability for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List. 5. GENERAL INFORMATION The information below is provided for clarification in meeting the requirements of these specifications. 5.1 Affected Material Specifications: WSK-M11P57-A1 relates to WSK-M2G379-A1 WSK-M11P57-A2 relates to WSK-M2G379-A2 WSK-M11P57-A3 relates to WSK-M2G379-A3 WSK-M11P57-A4 relates to WSK-M2G379-A4

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1