FORD WSK-M4D550-A6-2010 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 25% MINERAL FILLED MEDIUM HIGH IMPACT HIGH SCRATCH RESISTANT MOLDING COMPOUND MULTI SPOT DECOR INTERIOR TO BE USED.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 07 Revised/ A6- NSTATUS Completely revised and added B version, A6 TO BE N-STATUS, No replacement. V.Cerato and Global Material Team 2005 09 06 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.11, 3.12 & 4 1987 01 23 Released SM/EQ 5668

2、TP L. RodigasPrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 6 THERMOPLASTIC POLYOLEFIN ELASTOMER (TPO) 15% MINERAL WSK-M4D550-A FILLED, MEDIUM HIGH IMPACT MOLDING COMPOUND, HIGH SCRATCH RESISTANT MOLDING COMPOUND, INTERIOR THERMOPLASTIC POLYOLEFIN ELASTOMER (

3、TPO) 25% WSS-M4D550-B MINERAL FILLED, MEDIUM HIGH IMPACT, HIGH SCRATCH RESISTANT MOLDING COMPOUND, INTERIOR THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 25% WSK-M4D550-A6 MINERAL FILLED, MEDIUM HIGH IMPACT, HIGH SCRATCH RESISTANT MOLDING COMPOUND, MULTI SPOT DECOR, INTERIOR - NOT TO BE USED FOR NEW DESI

4、GN 1. SCOPE The materials defined by these specifications are rigid moulded in colour thermoplastic polyolefin elastomer (TPO) injection moulding compounds, mineral filled, with medium high impact and qualified to fulfill higher requirements for scratch resistance. 2. APPLICATION These specification

5、s were released originally for materials used for instrument panels. 2.1 LIMITATIONS Mould-in-color part using this material must comply with all the requirements of WSS-M15P4-Latest. Production level materials must be used in preparing test parts / panels. The use of improper sample prep materials

6、can influence test results. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements. For Production Materials (WSS-M99P1111-A). 3.1.1 All requirements of this specification, identified by symbol(s), s

7、hall be met with data representing 3 sigma values using latest ISO test methods. NOTE: Statistical data shall be derived from testing a minimum of 30 lots. The statistical data shall be submitted with initial qualification data. For provisional approval prior to completion of 30 lots testing, statis

8、tical data shall be derived from testing of 30 evenly divided subgroups from a minimum of 3 lots. These data shall be included with the specification draft when requesting a new specification. After completion of 30 lots testing, specification values may be revised to reflect the final results. ENGI

9、NEERING MATERIAL SPECIFICATIONWSK-M4D550-A/A6/ WSS-M4D550-BPrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 7 For materials used in applications requiring small amounts (less than 3 lots) the above requirement may be waived at the option of the affected Product

10、 Development Materials Activity. 3.1.2 This specification is based on virgin materials, however materials with recycled content as defined by WSS-M99P42-A (post-consumer and/or post industrial recyclates and repolymerised recycled materials) should be used whenever technically feasible and following

11、 all materials and PV testing required by Ford Materials Engineering. The use of regrind is permitted, for economic / environmental reasons, with compliance as indicated in WSS-M99P1111-A. Critical Process Parameters At the request of Ford Materials Engineering the supplier shall be responsible to c

12、ollect critical process control data on each lot of material produced. Testing required will be jointly developed between Ford Materials Engineering and the supplier based on Control Plan and PFMEA review at the time of initial approval. Annually the supplier will review the in process data with For

13、d Materials Engineering to show that the process has remained under control. The data needs to be submitted in January for the previous calendar year. Data showing poor quality control measures or lack of submitted data may result in deletion from the Ford Approved Source List. 3.2 MOLDING COMPOUND

14、A B A6(s) 3.2.1 Filler Content % (ISO 3451-1, Method A, talc filler, 1 h at 850 +/- 50 C, test portion 2 to 2.5 g) 3.3 MOLDED TEST SPECIMEN 3.3.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following di

15、mensions are required: A. 150 minimum x 10 x 4.0 +/- 0.2 mm (ISO 527-2, specimen type 1A) B. 150 x 100 x 3.2 +/- 0.2 mm (ISO2577) C. 355 x 100 x 1.0 +/-0.1 mm (ISO 3795) NOTE: The recommended thickness tolerances on all test specimens are +/- 0.1 mm. Test specimen A shall be molded using molding con

16、ditions defined in ISO 1873-2. Specimens with shorter dimensions shall be cut from the center of the specimen A. No annealing allowed. 3.3.2 Density g/cm3(ISO 1183, Method A), (s) 3.3.3 Tensile Strength at Yield, min 17 MPa (ISO 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A, test s

17、peed: 50 mm/minute) 13-18 23-28 23-28 A 0.95-1.05 B 1.06-1.13 A6 1.08-1.13 ENGINEERING MATERIAL SPECIFICATIONWSK-M4D550-A/A6/ WSS-M4D550-BPrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 6 (s) 3.3.4 Tensile Modulus, min 1.45 GPa (ISO 527-1 & ISO 527-2, 150 mini

18、mum x 10 x 4.0 +/- 0.2 mm specimen A test speed: 1 mm/min) (s) 3.3.5 Flexural Modulus, min 1.6 GPa (ISO 178, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, 2 mm/min test speed, 64 mm support span) NOTE 1: To obtain statistically valid data, a transformation of non-normal raw dat

19、a is allowed, e.g. conversion to the natural logarithms, calculation of - 3 sigma value, and finally, retransformation to original metric (antilogarithm) value. (s) 3.3.6 Impact Strength, Izod, min (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, 10 specimens for each

20、 test) 3.3.6.1 At 23 +/- 2 C 20 kJ/m23.3.6.2 At - 40 +/- 2 C 2.5 kJ/m23.3.6.3 At 10 +/- 2 C 6.0 kJ/m2The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold chamber, if not possible, t

21、est may be conducted outside, but within 5 seconds. (s) 3.3.7 Heat Deflection Temperature, min (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection.) 3.3.7.1 At 1.80 MPa 48 C 3.3.8 Heat Aging Performance (ISO 188, except 150 +

22、/- 50 air changes/h, 1000 h at 120 +/- 2 C. After heat aging test specimens are to be conditioned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.3.8.1 Tensile Strength at Yield Change +/- 25% (Test Method per

23、para 3.3.3) 3.3.8.2 Impact Strength, Izod Change, -25% max (Test Method per para 3.3.6.1, specimens to be notched before heat aging) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D550-A/A6/ WSS-M4D550-BPrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 6 3.3.9 Odor, ma

24、x (FLTM BO 131-03) Rating 3 3.3.10 Fogging (SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post test conditioning 16 h) Fog Number, min 80 Formation of clear film, droplets or crystals is cause for rejection. 3.3.11 Flammability (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute The specimen siz

25、e required for material approval is 355 x 100 x 1.0 +/- 0.1 mm (use specimen C) with a smooth surface. 4. SPECIAL REQUIREMENTS 4.1 WEATHERING RESISTANCE After exposure in accordance with 4.1.1 the material shall show no fading or color change in excess of specified Gray Scale rating (AATCC Evaluatio

26、n Procedure 1/ISO 105-A02). In addition, there shall be no cracking, crazing or other deterioration. 4.1.1 Filtered Xenon Arc Weatherometer, min Rating 4 (FLTM BO 116-01 2481.6 kJ/m2 exposure monitored at 420 nm, specimen size: 150 x 100 mm min, 3.2 +/- 0.2 mm thick, moulded in smooth polished mould

27、). Use current program black, grey and tan colors for initial approval. Color submissions: All Program Colors 4.2 RESISTANCE TO SCRATCHING (FLTM BO 162-01, visual evaluation, 1 mm scratch balls at 2.0 N, 3.0 N, and 7.0 N load) Hard Instrument Panels Scratch 2 N, Rating 2 max Whitening/Color Change 1

28、5 N, Rating 1 max Marring 2 N, Rating 2 max Hard Trim Scratch 2 N, Rating 2 max Whitening/Color Change 7 N, Rating 1 max Marring 2 N, Rating 2 max Note 1: Scratch - defined as a deformation or cutting of the grained/ungrained surface. Whitening/Color Changes - defined as a white line or color change

29、 visible at all angles for mold in color materials. Marring - Defined as a gloss change or burnishing with no deformation or whitening of the surface. ENGINEERING MATERIAL SPECIFICATIONWSK-M4D550-A/A6/ WSS-M4D550-BPrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 o

30、f 6 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of these specifications. 5.1 MELT FLOW RATE g/10 minutes Report value (ISO 1133, 230 C, 2.16 kg) 5.2 HEAT DEFLECTION TEMPERATURE, min (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/

31、- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection.) 5.2.1 At 0.45 MPa 93 C 5.3 COEFFICIENT OF LINEAR THERMAL EXPANSION (ISO 11359-2, -30 to 100C) 5-9 E-5mm/mm/ C 5.4 MOLD SHRINKAGE (ISO 2577, approximately 150 x 100 x 3.2 +/- 0.2 mm injection molded specimen B)

32、 5.4.1 Molding Shrinkage . After 48 h at 23 +/- 2 C 0.8 - 1.2% 5.4.2 Post Shrinkage (Separate specimens required for each test) . After 48 h at 80 C 0.1 - 0.2% . After 30 minutes at 120 C 0.1 - 0.3% 5.5 GLOSS (FLTM BI 110-01, Glossmeter 60 , 5 measurements min on grained surfaces, grain: Cordwain an

33、d/or equivalents) Gloss Level, max As specified by Design activity 5.6 USE OF REGRIND MATERIAL (Property values of regrind material shall be compared with original virgin material. Regrind: compound of 20 weight % regrind based on single reprocessed material, free of contaminations, and 80 weight %

34、virgin material) 5.6.1 Tensile Strength at Yield Change +/- 10% (Test method per para 3.3.3) 5.6.2 Flexural Modulus, Change +/- 10% (Test method per para 3.3.5) 5.6.3 Impact Strength, Izod Change, max -10% (Test method per para 3.3.6.1) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D550-A/A6/ WSS-M4D550-B

35、Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 6 of 6 5.6.4 Heat Deflection Temperature Change +/- 10% (Test method per para 3.3.7.1) 5.6.5 Weathering Resistance 5.6.5.1 Filtered Xenon Arc Weatherometer Rating 4 (Test method per para 4.1.1) 5.6.6 Resistance to Scratching (Test method per para 4.2) Percentage of Marking, Change, max 0% 5.6.7 Melt Flow Rate Change, max +30% (Test method per para 5.1) 5.7 MATERIAL IDENTIFICATION FOR RECYCLING PURPOSES (ISO 1043/18064 latest) A B A6 PP+EPM-TD15PP+EPM-TD25PP+EPM-TD25