FORD WSK-M4D556-A-2010 POLYPROPYLENE COPOLYMER 22% MINERAL FILLED INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用22%矿物填充的聚丙烯(PP)共聚物 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSK-.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 05 19 Revised Completely revised, WSK-M4D556-A/A3/A5 is replaced by WSK-M4D556-A4 V.Cerato and Global Material Team 2005 09 06 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.11, 3.12 & 4 1987 01 23 Released SM/EQ 5668 TP L. Rodigas Printe

2、d copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 7 POLYPROPYLENE COPOLYMER, 22% MINERAL FILLED, WSK-M4D556-A INTERIOR NOT TO BE USED FOR NEW DESIGN POLYPROPYLENE COPOLYMER, 22% MINERAL FILLED, MEDIUM WSK-M4D556-A3 SCRATCH RESISTANT MOLDING COMPOUND, INTERIOR NOT TO B

3、E USED FOR NEW DESIGN POLYPROPYLENE COPOLYMER, 15% MINERAL FILLED, HIGH WSK-M4D556-A4 SCRATCH RESISTANT MOLDING COMPOUND, INTERIOR POLYPROPYLENE COPOLYMER, 24% MINERAL FILLED, HIGH WSK-M4D556-A5 SCRATCH RESISTANT MOLDING COMPOUND, MULTI SPOT DECOR, INTERIOR NOT TO BE USED FOR NEW DESIGN 1. SCOPE The

4、 materials defined by these specifications are colored 15 to 24 % mineral filled injection moulding compounds based on polypropylene copolymers. WSK-M4D556-A3, -A4 and -A5 materials are qualified to fulfill higher requirements for scratch resistance. WSK-M4D556-A5 material shows additionally multi s

5、pot decor effects. 2. APPLICATION These specifications were released originally for materials used for various interior applications such as pillar trims, door bins, package tray side supports etc. 2.1 LIMITATIONS Mold-in-color part using this material must comply with all the requirements of WSS-M1

6、5P4-Latest. Production level materials must be used in preparing test parts / panels. The use of improper sample prep materials can influence test results. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard R

7、equirements. For Production Materials (WSS-M99P1111-A). 3.1.1 All requirements of this specification, identified by symbol(s), shall be met with data representing 3 sigma values using latest ISO test methods. 3.1.2 This specification is based on virgin materials, however materials with recycled cont

8、ent as defined by WSS-M99P42-A (post-consumer and/or post industrial recyclates and repolymerised recycled materials) should be used whenever technically feasible and following all materials and PV testing required by Ford Materials Engineering. The use of regrind is permitted, for economic / enviro

9、nmental reasons, with compliance as indicated in WSS-M99P1111-A. ENGINEERING MATERIAL SPECIFICATIONWSK-M4D556-A/A3/A4/A5Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 6 Critical Process Parameters At the request of Ford Materials Engineering the supplier shal

10、l be responsible to collect critical process control data on each lot of material produced. Testing required will be jointly developed between Ford Materials Engineering and the supplier based on Control Plan and PFMEA review at the time of initial approval. Annually the supplier will review the in

11、process data with Ford Materials Engineering to show that the process has remained under control. The data needs to be submitted in January for the previous calendar year. Data showing poor quality control measures or lack of submitted data may result in deletion from the Ford Approved Source List.

12、3.2 MOLDING COMPOUND A/A3/A5 A4(s) 3.2.1 Filler Content % (ISO 3451-1, Method A, talc filler, 1 h at 850 +/- 50 C, test portion 2 to 2.5 g) 3.3 MOLDED TEST SPECIMEN 3.3.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test sp

13、ecimens. The following dimensions are required: A. 150 minimum x 10 x 4.0 +/- 0.2 mm (ISO 527-2, specimen type 1A) B. 355 x 100 x 1.0 +/-0.1 mm (ISO 3795) NOTE: The recommended thickness tolerances on all test specimens are +/- 0.1 mm. Test specimen A shall be molded using molding conditions defined

14、 in ISO 1873-2. Specimens with shorter dimensions shall be cut from the center of the specimen A. No annealing allowed. A/A3/A5 A4 3.3.2 Density g/cm3(ISO 1183, Method A), (s) 3.3.3 Tensile Strength at Yield, min 20 MPa (ISO 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A, test speed

15、: 50 mm/minute) 3.3.4 Tensile Modulus, min (ISO 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A test speed: 1 mm/min, 10 specimens) (s) 3.3.5 Flexural Modulus, min (ISO 178, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, 2 mm/min test speed, 64 mm support span) 1

16、9-27 13-191.01-1.11 0.95-1.05 A A3/A4/A5 1.8 GPa 1.7 GPa A A3/A4/A5 2.0 GPa 1.9 GPa ENGINEERING MATERIAL SPECIFICATIONWSK-M4D556-A/A3/A4/A5Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 6 (s) 3.3.6 Impact Strength, Izod, min (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2

17、 mm specimen use center section of specimen A, 10 specimens for each test) 3.3.6.1 At 23 +/- 2 C 3.3.6.2 At - 40 +/- 2 3.3.6.3 At 10 +/- 2 C The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done wit

18、hin the cold chamber, if not possible, test may be conducted outside, but within 5 seconds. (s) 3.3.7 Heat Deflection Temperature, min (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection.) 3.3.7.1 At 1.80 MPa 52 C 3.3.8 Heat

19、Aging Performance (ISO 188, except 150 +/- 50 air changes/h, 1000 h at 140 +/- 2 C. After heat aging test specimens are to be conditioned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.3.8.1 Tensile Strength a

20、t Yield Change - 25% (Test Method per para 3.3.3) 3.3.8.2 Impact Strength, Izod Change, max -25% (Test Method per para 3.3.7.1, specimens to be notched before heat aging) 3.3.9 Odor, max (FLTM BO 131-03) Rating 3 3.3.10 Fogging (SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post test conditio

21、ning 16 h) Fog Number, min 80 Formation of clear film, droplets or crystals is cause for rejection. 3.3.11 Flammability (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm (use specimen B) with a smooth surface. A A3/A5 A4 4

22、 kJ/m24 kJ/m24 kJ/m22 kJ/m21.8 kJ/m21.8 kJ/m23.5 kJ/m23 kJ/m22.8 kJ/m2ENGINEERING MATERIAL SPECIFICATIONWSK-M4D556-A/A3/A4/A5Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 6 4. SPECIAL REQUIREMENTS 4.1 WEATHERING RESISTANCE After exposure in accordance with 4

23、.1.1 the material shall show no fading or color change in excess of specified Gray Scale rating (AATCC Evaluation Procedure 1/ISO 105-A02). In addition, there shall be no cracking, crazing or other deterioration. 4.1.1 Filtered Xenon Arc Weatherometer, min Rating 4 (FLTM BO 116-01 2481.6 kJ/m2 expos

24、ure monitored at 420 nm, specimen size: 150 x 100 mm min, 3.2 +/- 0.2 mm thick, moulded in smooth polished mould). Use current program black, grey and tan colors for initial approval. Color submissions: All Program Colors 4.2 RESISTANCE TO SCRATCHING (FLTM BO 162-01, visual evaluation, 1 mm scratch

25、balls at 2.0 N, 3.0 N, and 7.0 N load) Hard Trim Scratch 2 N, Rating 2 max Whitening/Color Change 7 N, Rating 1 max Marring 2 N, Rating 2 max Note 1: Scratch - defined as a deformation or cutting of the grained/ungrained surface. Whitening/Color Changes - defined as a white line or color change visi

26、ble at all angles for mold in color materials. Marring - Defined as a gloss change or burnishing with no deformation or whitening of the surface. 4.3 MULTI SPOT DECOR EFFECT (WSK-M4D556-A5 only) The Decor Effect must comply with the requirements as defined and approved by the Design Activity. ENGINE

27、ERING MATERIAL SPECIFICATIONWSK-M4D556-A/A3/A4/A5Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 of 6 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of these specifications. 5.1 MELT FLO

28、W RATE g/10 minutes Report value (ISO 1133, 230 C, 2.16 kg) 5.2 HEAT DEFLECTION TEMPERATURE, min (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection.) 5.2.1 At 0.45 MPa 102 C 5.3 POISSONS RATIO Report ratio Test method ISO 52

29、7-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm (specimen A), test speed 1mm/minute. 5.4 COEFFICIENT OF LINEAR THERMAL EXPANSION (ISO 11359-2, -30 to 100C) 8-12 E-5mm/mm/ C 5.5 MOLD SHRINKAGE (Report test method used and specimen dimensions) 5.5.1 Molding Shrinkage 5.5.1.1 After 48 h at 23 +/- 2

30、C, Flow Direction Report Value, % 5.5.1.2 After 48 h at 23 +/- 2 C, Cross Flow Direction Report Value, % 5.6 GLOSS (FLTM BI 110-01, Glossmeter 60, 5 measurements min on grained surfaces, grain: Cordwain and/or equivalents) Gloss Level, max As specified by Design activity 5.7 USE OF REGRIND MATERIAL

31、(Property values of regrind material shall be compared with original virgin material. Regrind: compound of 20 weight % regrind based on single reprocessed material, free of contaminations, and 80 weight % virgin material) 5.7.1 Tensile Strength at Yield Change, max -10% (Test method per para 3.3.3)

32、5.7.2 Flexural Modulus, Change, max -10% (Test method per para 3.3.5) 5.7.3 Impact Strength, Izod Change, max -10% (Test method per para 3.3.6) 5.7.4 Heat Deflection Temperature Change +/- 10% (Test method per para 3.3.7) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D556-A/A3/A4/A5Printed copies are unco

33、ntrolled Copyright 2010, Ford Global Technologies, LLC Page 6 of 6 5.7.5 Weathering Resistance 5.7.5.1 Filtered Xenon Arc Weatherometer, min Rating 4 (Test method per para 4.1.1) 5.7.6 Resistance to Scratching (Test method per para 4.2) Percentage of Marking, Change, max 0% 5.7.7 Melt Flow Rate Change, max +30% (Test method per para 5.1) 5.8 MATERIAL IDENTIFICATION FOR RECYCLING PURPOSES (ISO 1043/18064 latest) A4 A/A3 A5 PP-TD15PP-TD20PP-TD25