FORD WSK-M4D596-A-2010 POLYAMIDE (PA) 66 HEAT STABILIZED 50% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用受热稳定、50%玻璃纤维增强的聚酰胺66成型料 与标准FORD WS.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 08 N-STATUS No replacement named J. Crist, NA 2005 09 13 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.8, 3.9 & 4 1988 06 15 Released SM/EQ4331TP M. Siewert Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC

2、 Page 1 of 4 POLYAMIDE (PA) 66, HEAT STABILIZED 50% GLASS WSK-M4D596-A FIBER REINFORCED MOLDING COMPOUND NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a heat stabilized glass fiber reinforced polyamide 66 molding compound. 2. APPLICATION This specification was

3、released originally for material used for the cage of automatic transmission clutch. NOTICE: This material absorbs and retains moisture. Part design and tolerances must accommodate changes in part dimensions and physical properties due to moisture absorption or loss in the service/assembly environme

4、nt. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 MO

5、LDING COMPOUND 3.4.1 Glass Fiber Content 47 - 53% (ISO 3451/4, test temperature 600 +/-25 C, test portion 1 g) 3.4.2 Melt Temperature 250 - 265 C (ISO 1218, Method B/ASTM D 789, or DSC - ASTM E 794) 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests sha

6、ll be carried out on injection molded one-end gated test specimens. The following dimensions are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (Tensile Bar, ISO 3167) B. 120 x 10 x 4.0 +/- 0.2 mm Specimens with shorter dimensions shall be cut from the center portion of the test specimen A and/or B. The

7、 specimens shall be prepared according to ISO 294. No annealing allowed.ENGINEERING MATERIAL SPECIFICATIONWSK-M4D596-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 4 3.5.2 Density 1.54 - 1.60 g/cm3(ISO 1183, Method A/ASTM D 792, Method A1) 3.5.3 Tensile Str

8、ength at Max Load, min 190 MPa (ISO R 527/ASTM D 638M, 150 x 10 x 4.0 +/- 0.2 mm specimen, 5 mm/minute test speed) 3.5.4 Flexural Modulus, min 11 GPa (ISO 178/ASTM D 790M, Method I, Procedure A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 64 mm support span) 3.5.5 Shear Modulus at 23 C 2.11 - 3.51 GPa (ASTM

9、D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specimen approx. 60 x 10 x 4.0 +/- 0.2 mm cut from the center of specimen A. Specimen length between clamps 35-40 mm. Soak time at each temperature interval - 3 minutes minimum) Additionally, a Shear Modulus v

10、s. Temperature curve shall be plotted for -50 to +240 C temperature range, at 5 C minimum intervals. The plotted curve must be within tolerance range shown on page 4. 3.5.6 Impact Strength, Izod, min (ISO 180, Method A/ASTM D 256, Method A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens for each te

11、st) 3.5.6.1 At 23 +/- 2 C 12 kJ/m23.5.6.2 At -40 +/- 2 C 8 kJ/m2The test specimens must be conditioned for a minimum of 6 h at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold box, if not possible, test can be conducted outside, but within 5

12、 s. 3.5.7 Heat Deflection Temperature, min (ISO 75/ASTM D 648, 120 x 10 x 4.0 +/- 0.2 mm specimen) 3.5.7.1 At 1.82 Mpa 240 C 3.5.7.2 At 0.45 Mpa 250 C 3.5.8 Heat Aging Performance (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 140 +/- 2 C. After heat aging test specimens are to be conditio

13、ned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.5.8.1 Impact Strength, Izod Change +/- 25% (Test Method per para 3.5.6.1, specimens to be notched before heat aging) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D

14、596-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 4 3.6 FLAMMABILITY (ISO 3795) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm with a smooth surface. 3.7 FOGGING (SAE J1756, 3 h at 100 C heating,

15、 21 C cooling plate, post test conditioning 1 h and 16 h) Fog Number, min 90 Formation of clear film, droplets or crystals is cause for rejection. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 CO

16、EFFICIENT OF LINEAR THERMAL EXPANSION 1.5 - 2.2-5/ C (ASTM D 696) 5.2 MOLD SHRINKAGE (ISO 2577, approx. 150 x 100 x 3.2 +/- 0.2 mm injection molded specimen) 5.2.1 Molding Shrinkage After 48 h at 23 +/- 2 C 0.1 - 1.3% 5.2.2 Post Shrinkage (Separate specimens required for each test) After 48 h at 80

17、C 0.01 - 0.10% After 30 minutes at 120 C 0.01 - 0.10% 5.3 WATER ABSORPTION 0.3 - 0.9% (ISO 62, 24 h/ASTM D 570, 24 h, 50 +/- 1 mm diameter, 3.2 +/- 0.2 mm thick specimen) 5.4 IMPACT STRENGTH, IZOD, min (ISO 180, Method A/ASTM D 256, Method A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens minimum)

18、5.4.1 After Moisture Conditioning 20 kJ/m2The notched specimens shall be immersed for 48 h in distilled water at 50 +/- 1 C and subsequently conditioned for 1 h at 23 +/- 2 C and 50 +/- 5% relative humidity prior to test and tested under the same conditions within 1 h. ENGINEERING MATERIAL SPECIFICATIONWSK-M4D596-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 4