FORD WSK-M4D654-A2-2012 POLYAMIDE 66 (PA66) HEAT STABILIZED 40% GLASS SPHERE REINFORCED MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 04 2012 11 28 N Status No replacement named L. Soreide, NA 2006 12 06 Revised Inserted 3.8.3, Revised 3.8, 3.8.1, 3.8.2 C. Leslie 1991 12 02 Released EP00E01089491000 K. Gerhards Controlled document at www.MATS Copyright 2012, Ford Global

2、 Technologies, LLC Page 1 of 5 POLYAMIDE 66 (PA66), HEAT STABILIZED 40% GLASS WSK-M4D654-A2 SPHERE REINFORCED MOLDING COMPOUND, INTERIOR NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a heat stabilized 40% glass sphere reinforced polyamide 66 molding compound wi

3、th added UV stabilization for interior use. 2. APPLICATION This specification was released originally for material used for steering column switch. NOTICE: This material absorbs and retains moisture. Part design and tolerances must accommodate changes in part dimensions and physical properties due t

4、o moisture absorption or loss in the service/assembly environment. 3. REQUIREMENT Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

5、Requirements For Production Materials (WSS-M99P1111-A). 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material and specimens with moisture content not exceeding 0.2% (test according to ISO 960, Method B/ASTM D 789). All test materials immediately after processing

6、 have to be sealed in containers that are impermeable to water vapor. If the moisture content exceeds 0.2%, condition the material for a minimum of 16 h at 40 - 50 C at a reduced pressure below 133 Pa. Conduct tests in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity. Individual

7、 specimens shall not be removed from closed containers until immediately before testing. 3.4 MOLDING COMPOUND 3.4.1 Glass Sphere Content 37.5 - 42.5% (ISO 3451/4, test temperature 600 +/- 25 C, test portion 1 g) 3.4.2 Melt Temperature 250 - 265 C (ISO 1218, Method B/ASTM D 789, or DSC - ASTM E 794)

8、ENGINEERING MATERIAL SPECIFICATION WSK-M4D654-A2 Copyright 2012, Ford Global Technologies, LLC Page 2 of 5 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following dimensions

9、 are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (Tensile Bar, ISO 3167) B. 120 x 10 x 4.0 +/- 0.2 mm Specimens with shorter dimensions shall be cut from the center portion of the test specimen A and/or B. The specimens shall be prepared according to ISO 294. No annealing allowed. 3.5.2 Density 1.43

10、- 1.50 g/cm (ISO 1183, Method A/ASTM D 792, Method A1) 3.5.3 Tensile Strength at Max Load, min 70 MPa (ISO R 527/ASTM D 638M, 150 x 10 x 4.0 +/- 0.2 mm specimen, 5 mm/minute test speed) 3.5.4 Flexural Modulus, min 4.0 GPa (ISO 178/ASTM D 790M, Method I, Procedure A, 80 x 10 x 4.0 +/- 0.2 mm specimen

11、, 2 mm/min test speed, 64 mm support span, the radius of the loading nose 5.0 +/- 0.1 mm and of the supports 2.0 +/- 0.2 mm) 3.5.5 Shear Modulus at 23 C 1.55 - 2.59 GPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specimen approx. 60 x 10 x 4.0 +/-

12、 0.2 mm cut from the center of specimen A. Specimen length between clamps 35 - 40 mm. Soak time at each temperature interval - 3 minutes minimum) Additionally, a Shear Modulus vs. Temperature curve shall be plotted for -50 to +240 C temperature range, at 5 C minimum intervals. The plotted curve must

13、 be within tolerance range shown on page 5. 3.5.6 Impact Strength, Izod, min (ISO 180, Method A/ASTM D 256, Method A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens for each test) 3.5.6.1 At 23 +/- 2 C 2 kJ/m 3.5.6.2 At -40 +/- 2 C 1.5 kJ/m The test specimens must be conditioned for minimum of 6 h

14、at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold box, if not possible, test can be conducted outside, but within 5 s. ENGINEERING MATERIAL SPECIFICATION WSK-M4D654-A2 Copyright 2012, Ford Global Technologies, LLC Page 3 of 5 3.5.7 Heat De

15、flection Temperature, min (ISO 75/ASTM D 648, 120 x 10 x 4.0 +/- 0.2 mm specimen, at standard deflection of 0.32 +/- 0.01 mm) 3.5.7.1 At 1.80 MPa 80 C 3.5.7.2 At 0.45 MPa 215 C 3.5.8 Heat Aging Performance (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 130 +/- 2 C. After heat aging test sp

16、ecimens are to be conditioned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.5.8.1 Impact Strength, Izod Change +/- 25% (Test Method per para 3.5.6.1, specimens to be notched before heat aging) 3.6 FLAMMABILIT

17、Y (ISO 3795) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm with a smooth surface. 3.7 FOGGING SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post test conditioning 1 h and 16 h) Fog Number, min 90 Formation of excessive amounts of c

18、lear film or droplets is cause for rejection. 3.8 WEATHERING RESISTANCE After exposure in accordance with 3.8.1, 3.8.2 and 3.8.3 the material shall show no fading or color change in excess of specified AATCC rating (AATCC Gray Scale for Evaluating Change in Color, 10 step). In addition, there shall

19、be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be achieved by washing with mild detergents and water (ratio 5:95 by volume), or equivalent, after the Florida exposure. All initial approvals will be based on the

20、 preliminary Weatherometer exposure, pending Florida exposure results for final approval Not required for North America. 3.8.1 Xenon Arc Weatherometer Rating 4 Required Worldwide except North America (SAE J1885, 601.6 kJ/m exposure minimum, specimen size: 150 x 100 mm minimum, 3.2 +/- 0.2 mm thick,

21、molded in smooth polished mold) ENGINEERING MATERIAL SPECIFICATION WSK-M4D654-A2 Copyright 2012, Ford Global Technologies, LLC Page 4 of 5 3.8.2 12 months Florida Rating 4 Not required for North America (FLTM BI 160-01, 5 south, under glass, specimen size: 150 x 100 mm, minimum, 3.2 +/- 0.2 mm thick

22、, molded in smooth polished mold) 3.8.3 Filtered Xenon Arc Weatherometer Rating 4 Required for North America (SAE J1885 modified (FLTM BO 116-01), 1203.2 kJ/m2 exposure min, specimen size: 150 x 100 mm min, 3.2 +/- 0.2 mm thick, molded in smooth polished mold) 5. GENERAL INFORMATION The information

23、given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 COEFFICIENT OF LINEAR THERMAL EXPANSION 5 - 8-5/C (ASTM D 696) 5.2 MOLD SHRINKAGE (ISO 2577, approx. 150 x 100 x 3.2 +/- 0.2 mm injection molded specimen) 5.2.1 Molding Shrinkage . After 4

24、8 h at 23 +/- 2 C 1.0 - 1.6% 5.2.2 Post Shrinkage (Separate specimens required for each test) . After 48 h at 80 C 0.05 - 0.30% . After 30 minutes at 120 C 0.05 - 0.30% 5.3 WATER ABSORPTION 0.6 - 0.8% (ISO 62, 24 h/ASTM D 570, 24 h, 50 +/- 1 mm diameter, 3.2 +/- 0.2 mm thick specimen) 5.4 IMPACT STR

25、ENGTH, IZOD, min (ISO 180, Method A/ASTM D 256, Method A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens minimum) 5.4.1 After Moisture Conditioning 5 kJ/m The notched specimens shall be immersed for 48 h in distilled water at 50 +/- 1 C and subsequently conditioned for 1 h at 23 +/- 2 C and 50 +/- 5% relative humidity prior to test and tested under the same conditions within 1 h. 5.5 RECYCLING CODE PA66 GB40 ENGINEERING MATERIAL SPECIFICATION WSK-M4D654-A2 Copyright 2012, Ford Global Technologies, LLC Page 5 of 5