FORD WSK-M4D890-A2-2010 POLYAMIDE 6-3-T (PA6-3-T) AMORPHOUS MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用聚酰胺6-3-T（PA6-3-T）非定形成型料 与标准FORD WSS-M99P1111-A一起使.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 20 N-STATUS No replacement named J. Crist, NA 2006 05 31 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.9, 3.10 & 4 1994 09 01 Released EP00E10348605000 K. Gerhards Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, L

2、LC Page 1 of 5 POLYAMIDE 6-3-T (PA6-3-T), AMORPHOUS WSK-M4D890-A2 MOLDING COMPOUND, EXTERIOR NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a UV stabilized, amorphous polyamide molding compound based on poly (trimethylhexamethylene terephthalamide). 2. APPLICATI

3、ON This specification was released originally for material used as door lock IR receiver. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1.1 All r

4、equirements of this specification, identified by symbol(s), shall be met with data representing 3 sigma values. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material and specimens with moisture content not exceeding 0.2% (test according to ISO 960, Method B). Al

5、l test materials immediately after processing have to be sealed in containers that are impermeable to water vapor. If the moisture content exceeds 0.2%, condition the material for a minimum of 16 h at 40 - 50 C at a reduced pressure below 133 Pa. 3.4 MOLDING COMPOUND (s) 3.4.1 Glass Transition Tempe

6、rature 145 - 155 C (ASTM D 3418, DSC) 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following dimensions are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (Tensile Bar, ISO 316

7、7) B. 120 x 10 x 4.0 +/- 0.2 mm ENGINEERING MATERIAL SPECIFICATIONWSK-M4D890-A2Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 5 Specimens with shorter dimensions shall be cut from the center portion of the test specimen A and/or B. The specimens shall be prep

8、ared according to ISO 294. No annealing allowed. 3.5.2 Density 1.10 - 1.14 g/cm (ISO 1183, Method A) (s) 3.5.3 Tensile Strength at Yield, min 85 MPa (ISO 527, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen, 50 mm/min test speed) (s) 3.5.3.1 Elongation at Yield, min 8% (Test Method according to para 3.5.

9、3) (s) 3.5.4 Flexural Modulus, min 2.5 GPa (ISO 178, 80 x 10 x 4.0 +/- 0.2 mm specimen, 2 mm/min test speed, 64 mm support span) 3.5.5 Shear Modulus at 23 C 1160 - 1740 MPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specimen approx. 60 x 10 x 4.0

10、 +/- 0.2 mm cut from the center of specimen A. Specimen length between clamps 35-40 mm. Soak time at each temperature interval - 3 minutes minimum) Additionally, a Shear Modulus versus Temperature curve shall be plotted for -50 to +180 C temperature range, at 5 C minimum intervals. The plotted curve

11、 must be within tolerance range shown on page 5. (s) 3.5.6 Impact Strength, Izod, min (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens for each test) 3.5.6.1 At 23 +/- 2 C 8 kJ/m 3.5.6.2 At -40 +/- 1 C 5 kJ/mThe test specimens must be conditioned for minimum of 6 h at the above specified

12、 temperature prior to impact test. Low temperature testing shall be done within the cold box. (s) 3.5.7 Heat Deflection Temperature, min (ISO 75, 120 x 10 x 4.0 +/- 0.2 mm specimen, 0.32 +/- 0.01 mm deflection) 3.5.7.1 At 1.80 MPa 125 C 3.5.7.2 At 0.45 MPa 140 C ENGINEERING MATERIAL SPECIFICATIONWSK

13、-M4D890-A2Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 5 3.5.8 Heat Aging Performance (ISO 188, except 150 +/- 50 air changes/h, 1000 h at 110 +/- 2 C. After heat aging test specimens are to be conditioned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged p

14、roperty values shall be determined at the time of the aged properties determination) 3.5.8.1 Tensile Strength at Max Load Change +/- 25% (Test Method per para 3.5.3) 3.6 FOGGING (FLTM BO 116-03, 3 h at 100 C) Fog Number, min 90 Formation of clear film, droplets, or crystals is cause for rejection. 3

15、.7 FLAMMABILITY (ISO 3795) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm with a smooth surface. 3.8 WEATHERING RESISTANCE After exposure in accordance with 3.8.1, 3.8.2, and 3.8.3, the material shall show no color change in excess of spec

16、ified Gray Scale rating (AATCC Evaluation Procedure 1/ISO 105-A02). In addition, there shall be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be achieved by washing and/or polishing with Ford car polish (auto wax

17、) after the outdoor exposure, at permission of the affected Product Development Materials Activity. All initial approvals will be based on the preliminary Weatherometer exposure, pending Florida and Arizona exposure results for final approval. 3.8.1 Xenon Arc Weatherometer Rating 4 (SAE J1960, 600 k

18、J/m exposure minimum, specimen size: 150 x 100 mm minimum, 3.2 +/- 0.2 mm thick, molded in smooth polished mold) 3.8.2 12 months Florida Rating 4 12 months Arizona (NAAO only) (SAE J1976, 5 south, direct weathering inland, specimen size: 150 x 100 mm, minimum, 3.2 +/- 0.2 mm thick, molded in smooth

19、polished mold) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D890-A2Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 5 3.8.3 24 months Florida Rating 3-4 24 months Arizona (NAAO only) (SAE J1976, 5 south, direct weathering inland, specimen size: 150 x 100 mm, minimum

20、, 3.2 +/- 0.2 mm thick, molded in smooth polished mold) 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 COEFFICIENT OF LINEAR THERMAL EXPANSION 4 8-5/ C (ASTM E 228 or TMA, temperature range -30 to

21、 +30 C) 5.2 MOLD SHRINKAGE (ISO 2577, approx. 150 x 100 x 3.2 +/- 0.2 mm injection molded specimen) 5.2.1 Molding Shrinkage . After 48 h at 23 +/- 2 C 0.65 - 0.85% 5.2.2 Post Shrinkage (Separate specimens required for each test) . After 48 h at 80 C 0.0 - 0.1% . After 30 min at 120 C 0.0 - 0.1% 5.3 WATER ABSORPTION 0.1 - 0.3% (ISO 62, 24 h immersion, 50 +/- 1 mm diameter, 3.2 +/- 0.2 mm thick specimen) 5.4 RECYCLING CODE PA6-3-T ENGINEERING MATERIAL SPECIFICATIONWSK-M4D890-A2Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 of 5