FORD WSK-M99J365-A-2006 ACID CATALYST CLEAR COAT SYSTEM BAKING EXTERIOR TOP COAT TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部面漆用烘烤型透明涂层系统用酸性催化剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 03 23 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.4, 3.11 and 4 2000 11 28 Revised Updated & revised para 3.3 A. Cockman 1990 02 01 Released C01031532 C. E. Herriott, concurred: J. Schult Printed copies are uncontrolled Copyright 2006, Ford

2、 Global Technologies, LLC Page 1 of 3 ACID CATALYST, CLEAR COAT SYSTEM, WSK-M99J365-A BAKING, EXTERIOR TOP COAT 1. SCOPE The material defined by this specification is a solution of acid catalyst in organic solvents. It is to be used in a clear coat of a base coat/ clear coat system required to provi

3、de the best exterior quality metallic finish. It shall be suitable for spray application. 2. APPLICATION This specification was released originally for a material to be used as an acid catalyst to make base coat/clear coat top coats suitable to use with relatively low baking temperatures. The cataly

4、st shall only be used for top coats/clear coats from the same source as required by the vendor. The amount of addition may vary depending on the quality of the top coats/clear coats specified. It is permitted to use acid catalysts from a source different to that of the top coat/clear coat if approve

5、d by Materials Laboratory of Product Engineering and agreed by the respective vendors. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to t

6、he Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 ULTRA VIOLET SPECTROGRAPHIC ANALYSIS All approved materials shall contain with Initial Sample Report an UV-spectroscopic analysis. The equipment used for this measurement is a Lambda 6 Integrating Sphere spectrophotomet

7、er or equivalent. This shall be recorded and filed by Quality Control or relevant Testing Laboratories of the Ford Motor Company. Subsequent material UV-spectroscopic analysis shall correspond to the data of the Initial Sample. 3.5 FLASH POINT The flash point shall conform to the safety regulations

8、applicable to the plant and/or country where the material shall be used. ENGINEERING MATERIAL SPECIFICATIONWSK-M99J365-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 3 3.6 COMPOSITION 3.6.1 Acid Essentially an acid dissolved in organic media in sufficient q

9、uantity and nature to effectively cure the acrylic resin clear coat system at reduced temperature. 3.6.2 Chlorinated Compounds No chlorinated compounds permitted. 3.6.3 Specific Composition When it is necessary to obtain specific data regarding material formulation, it is understood that the supplie

10、r will furnish such data on request. 3.7 PHYSICAL PROPERTIES 3.7.1 Non-volatile No Requirement (FLTM BI 102-01) 3.7.2 Density Initial Sample (ASTM D 1475) +/- 0.05 g/mL 3.7.3 Acid Number Initial Sample (ASTM D 1467) +/- 5 3.7.4 Shelf Stability During a storage of 6 months at room temperature, as sup

11、plied in the original container, it shall not discolor or gel. When mixed with the clear coat as received, it shall cause no gel or turbidity and must be free of settling which cannot be dispersed by normal agitation. The viscosity of the material shall not increase 3.8 PREPARATION OF TEST PANELS (F

12、LTM BI 115-02) 3.8.1 Amount of catalyst Amount of acid catalyst % to be added to WSK-M32J125-A shall be specified by supplier. 3.8.2 Baking Cycles In Plant Repair Enamels containing acid catalyst. Bake 10 minutes at 100 C metal temperature. 3.9 FILM AND RESISTANCE PROPERTIES Film and Resistance prop

13、erties shall be in accordance to the relevant requirements of Specification WSK-M32J125-A. ENGINEERING MATERIAL SPECIFICATIONWSK-M99J365-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 3 3.10 PAINT COMPATABILITY Prior to making any changes in properties and/

14、or composition of originally approved paint, the supplier must certify compliance to all requirements of Direct Glazing System specification (test values, not nominal values) and obtain approval from the responsible Materials Engineering activity. For approved Direct Glazing System contact the respo

15、nsible Materials Engineering activity. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 MANUFACTURING ENGINEERING REFERENCES Applicable Process Standard Vehicles which are produced in NAAO C-200 (F) General Painting C-600 (F) Electrocoat PL53-33 (F) Phosphate Vehicles which are produced in EAO C-800 PAINTING -PROCESS