FORD WSS-M15P27-F-2015 PERFORMANCE HEADLINING FORMED TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION PERFORMANCE, HEADLINING, FORMED WSS-M15P27-F NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is fully finished, unitized formed headlining assembly consisting of a face material and substrate layers. 2. APPLICATION This unitized c

2、omposite assembly is used as a headlining for passenger cars and trucks or as specified on the Engineering Drawing. Headliners bonded to body sheet metal must meet the requirements of WSB-M11P59-A. Testing must be conducted at each prototype and production build phase unless specified otherwise by F

3、ord Engineering. See Table 1 for DV/PV testing. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.1.1 Vehicle Interior Environment Quality Materials/

4、Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-C1/latest. Components in vehicles that will be TUV certified must also meet the requirements outlined in WSS-M99P2222-C2/latest. 3.2 APPEARANCE (FLTM BI 109-01) The color, p

5、attern, and finish shall match the approved Design Center master sample, or shall be as specified on the Engineering Drawing. 3.3 WEIGHT, g/m2As specified on the (FLTM BN 106-01) Engineering Drawing 3.4 TRANSVERSE STRENGTH*, min 20 N (SAE J949, average of maximum loads on 5 samples) *In addition, th

6、e part shall not be damaged during installation in the vehicle. Date Action Revisions Rev. 4 2015 08 05 N Status Replaced by WSS-M15P27-G1 A. Wagenhals, NA 2014 12 10 Editorial See Summary of Revisions A. Wagenhals, NA 2008 05 28 Activated M. Dumitrescu, FNA; J.Williams, FOE Controlled document at w

7、ww.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 7 ENGINEERING MATERIAL SPECIFICATION WSS-M15P27-F 3.5 DIMENSIONAL STABILITY (SAE J315 test both flat and deep draw areas of part, with measurements on A and B surfaces) After testing, there shall be no blistering or loss of adhesion of

8、the surface material, and visible distortion or shrinkage of the component. Method “A“ +/- 0.5% Method “C“ (following Method A) +/- 0.5% Or as otherwise specified on the engineering drawing. 3.6 ADHESION STRENGTH (FLTM BN 151-05, all environmental conditioning of the procedure with exceptions as ind

9、icated below*) Face to substrate 6 N min All layers shall be bonded at all points without blisters. All areas of the part shall meet adhesion values specified above. After conditioning, the coverstock shall not blister, bubble or show areas of no adhesion. In addition, adhesion of the face fabric sh

10、all be greater than 6 N unless otherwise specified in the material specification. * Exceptions from FLTM BN 151-05 are: Environmental Aging which shall be following the cycling steps of para 3.21 Autoclave Aging which will be performed according with para 3.22 And Cleaning for which an approved Bran

11、d Cleaner shall be used. 3.7 RESISTANCE TO HEAT AGING Rating 4 min (7 days at 90 +/- 2 C) The test specimen shall not show any change of color as above when examined using ISO 105-A02/AATCC Evaluation Procedure 1. Any spotty or non-uniform staining, discoloration or color tone change shall be cause

12、for rejection. The sample must not produce any unpleasant odors when hot. 3.8 ODOR (FLTM BO 131-03, all 3 conditions) Condition 1 = 23 +/- 2C Rating 3 max Condition 2 = 40 +/- 2C Rating 3 max Condition 3 = 65 +/- 2C Rating 3 max 3.9 FOGGING (SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post

13、test conditioning 16 h) Fog Number 70 min Formation of clear film, droplets or crystals is cause for rejection. Copyright 2015, Ford Global Technologies, LLC Page 2 of 7 ENGINEERING MATERIAL SPECIFICATION WSS-M15P27-F 3.10 RESISTANCE TO MILDEW The material shall exhibit no visual evidence of mildew

14、growth and/or objectionable odor after 7 days exposure in a humidity cabinet at 38 +/- 2 C and 98 +/- 2% relative humidity. 3.11 INDENTATION AND RECOVERY (FLTM BO 111-02, Method B, except load is 1.5 kg) The indented headliner must return to its original contour within 5 minutes. In addition, the pa

15、rt shall not be damaged during installation in the vehicle. 3.12 RESISTANCE TO ABRASION 150 cycles (SAE J948, 500 g, CS-10 wheels) No evidence of excessive surface deterioration. The resistance to abrasion of production materials shall be equal to or better than that exhibited by the sample original

16、ly approved by the Materials Engineering Activity. 3.13 RESISTANCE TO SCUFFING 25 cycles (SAE J365, 0.9 kg load, A head) No evidence of lifting, peeling, excessive scuffing or excessive surface deterioration. The resistance to scuffing of production materials shall be equal to or better than that ex

17、hibited by the sample originally approved by the Materials Engineering Activity. 3.14 RESISTANCE TO SNAGGING 25 cycles min (SAE J1530-A, 500 g load, H-18 wheels) Applicable to non-woven face fabrics No evidence of fiber pullout in excess of the material originally approved by Materials Engineering.

18、The print on printed fabrics shall not be removed. 3.15 RESISTANCE TO FADE (FLTM BO 116-01, ISO 105-A02/) AATCC Evaluation Procedure 1) 225.6 kJ/m2 Rating 4 min The material shall not exhibit any change in appearance, such as color tone change, fading in excess of the required AATCC rating. In addit

19、ion, the material shall not exhibit staining, blistering, or delamination. 3.16 RESISTANCE TO CROCKING (FLTM BN 107-01, AATCC Procedure 2) Dry Rating 4 min Wet Rating 4 min 3.17 RESISTANCE TO BLEEDING Rating 4 min (FLTM AN 101-01, AATCC Evaluation Procedure 2) 3.18 RESISTANCE TO WATER SPOTTING (FLTM

20、 AN 101-01) No spots shall remain after the distilled water has completely dried off. Copyright 2015, Ford Global Technologies, LLC Page 3 of 7 ENGINEERING MATERIAL SPECIFICATION WSS-M15P27-F 3.19 SOILING AND CLEANABILITY OF CLOTH, (AATCC Evaluation Procedure 2) After cleaning Rating 4 Marks with an

21、 artists charcoal crayon must be easily removed, using an approved Brand Interior Trim Cleaner, without serious damage to the face fabric. The print on printed fabrics shall not be removed. With moderate pressure mark the face fabric with the crayon, length of mark approximately 70mm by approximatel

22、y 2-3mm wide. There shall be no pilling of the face fabric after the above testing. Printed fabrics shall retain all print detail after cleaning. The performance of production material shall be equal to or better than that exhibited by the sample originally approved for production by the Materials E

23、ngineering Activity. 3.20 IDENTIFICATION MARKING The reverse side of each assembly must be marked in a suitable way to identify its production batch. There shall be no evidence of identification mark bleed through onto the cover materials surface, nor any staining of adjacent assemblies during stora

24、ge. 3.21 SIMULATED IN-CAR ENVIRONMENTAL AGING Headliner Sag, max 13 mm Edge Gap Deformation, max 3.5 mm Horizontal Movement, max 3.5 mm The headliner shall not show any delamination, loss of embossed definition, excessive deformation, or any objectionable surface imperfections. The attachment system

25、 shall not show any evidence of delamination or separation from the headliner or mating components. Test Method: Install a complete headliner using production assembly techniques, in an approved test buck or vehicle, representative of intended production dimensions. Expose the vehicle (with windows

26、open) or test buck to the following environmental cycle: Confirm with the affected Materials Engineering Activity for agreement prior to using test chambers with automated programmable test cycles for the listed test conditions below. Ramp speed 1 to 5 C per minute (record actual ramp speed on data

27、sheet). . 5 h at -30 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at 90 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 16 h at 50 +/- 2 C and 95 +/- 5% R.H. . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at -30 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at 90 +/- 2 C *Please note that this lis

28、t does not include ramp times to transition from level to level. Each specimen can have different size, geometry, density, etc. which impacts ramp times; therefore, each transition period will vary in length of time. Total test time should exceed 38 hrs due to time required to transition from level

29、to level. The sag test is to be conducted at the prototype stage using a fixture representing the vehicle fixing points. For full vehicle testing, during the CP phase, the test procedure given below will be Copyright 2015, Ford Global Technologies, LLC Page 4 of 7 ENGINEERING MATERIAL SPECIFICATION

30、WSS-M15P27-F maintained, but the method of achieving the check points is as follows: The check points will be achieved by drilling 6mm diameter holes in the headliner above the H points for depth micrometer measurements. The five points across the front and rear obscuration bands are noted by tape m

31、arkers attached to the front and a rear screen, an example is shown in the diagram. During the full vehicle test, the air vents are to be set to open and the windows are to be open. Check point locations are marked at the following locations on the test headliner: Front Edge along the windscreen obs

32、curation line, five points on one line beginning at the center point and spaced at approximately 220mm to the left and right of the center. Rear Edge along the rear screen line, with check points as above. Five checkpoint locations are also to be marked directly above the headform center points. The

33、 head form center points are to be determined from the H points on the vehicle layout drawing, shown on the diagram below. Moonroof/Sunroof eight checkpoint locations are to be determined according to the attached sketch. Test Criteria Depth measurements for each checkpoint location are to be noted

34、prior to and at the end of the environmental cycle. The test criterion is to be applied 24 hours after completion of the sag test. From the compiled test data a maximum desired sag of 3.5mm should be allowed across the Copyright 2015, Ford Global Technologies, LLC Page 5 of 7 ENGINEERING MATERIAL SP

35、ECIFICATION WSS-M15P27-F front and rear edges and around the moonroof/sunroof aperture and 13.0mm above the head form points. No irregularities in shape or contour should be observed No damage to the face fabric and material bonding is allowed. There should be no loosening of inserts or attachments.

36、 3.22 STEAM AUTOCLAVE AGING, Retained Strength min 50% of original This requirement applies to urethane foams used in headliner constructions (fabric backing and substrate). 3.22.1 ASTM D3574, TEST J 1, one autoclave cycle for 3 h at 105 C Applicable for all Temperate Markets 3.22.2 ASTM D3574, TEST

37、 J 2, two autoclave cycles of 5h at 120 C each Applicable for all Tropical, Sub Tropical and NA Markets. Flexible Foam: Adhesion strength method: Cut two adjacent 250 x 250 mm samples from the headliner. Expose one to steam autoclave aging. Dry the autoclaved samples for a period of 3 h at 100 C +/-

38、 5 C. Then condition for 24 h at 23 +/- 2 and 50% relative humidity. Die cut 50 mm wide strips from both sets of original and autoclave-aged samples and test foam peel adhesion per Method A of FLTM BN 151-05. Report the percentage retained foam adhesion strength of the autoclave-aged sample from the

39、 original. Rigid Foam: Transverse strength method - Cut a duplicate set of transverse strength samples per para 3.4. Expose one to steam autoclave aging. Then condition both for 24 h at 23 +/- 2 C and 50% relative humidity, evaluate transverse strength and report the percent retained transverse stre

40、ngth of the autoclave aged sample from the original. 3.23 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate 100 mm/minute max 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning

41、Engineering Material Specifications. 4.1 STORAGE AND ASSEMBLY To avoid crush marks on the face fabric, finished headliners are supplied in special pallets. They should not be removed from the pallets until required for fitting to the vehicle. To prevent soiling during handling and fitting operations

42、, the face side of the assembly may be covered by a self-adhesive polyethylene film. 5. SUMMARY OF REVISIONS 12/10/2014 Editorial Change Clarification on environmental cycling. Section 3.21. 02/25/2014 Editorial update: Added condition 1,2,3 to clarify odor requirement. 09/26/2012 Section 3 added pa

43、ra 3.1.1- Vehicle Interior Environment Quality Materials/Component Performance Requirements Copyright 2015, Ford Global Technologies, LLC Page 6 of 7 ENGINEERING MATERIAL SPECIFICATION WSS-M15P27-F Para 3.4 was 10N min Para 3.5 added A and B surfaces Para 3.6 updated with more test directions Para 3

44、.8 clarified, removed SAE J1351 Para 3.9 updated; 1 hr post conditioning evaluation removed Para 3.13 clarified Para 3.15 updated, removed SAE J2412 Para 3.21 updated Table 1 WSS-M15P27-F For Paragraphs DV PV Surrogate data from Material Spec Allowed 3.4 Transverse Strength X X 3.5 Dimensional Stabi

45、lity X 3.6 Adhesion Strength X X 3.7 Resistance to Heat Aging X 3.8 Odor X 3.9 Fogging X 3.10 Resistance to Mildew X 3.11 Indentation and Recovery X X 3.12 Resistance to Abrasion X X 3.13 Resistance to Scuffing X X 3.14 Resistance to Snagging X X 3.15 Resistance to Fade X 3.16 Resistance to Crocking

46、 X * * 3.17 Resistance to Bleeding X * * 3.18 Resistance to Water spotting X * * 3.19 Soiling and Cleanability of cloth X * * 3.20 Identification Marking X X 3.21 Simulated in-car environmental aging X X 3.22 Steam Autoclave Aging, Retained Strength X X 3.23 Flammability X X Copyright 2015, Ford Global Technologies, LLC Page 7 of 7