FORD WSS-M15P4-H-2017 ASSEMBLY PERFORMANCE HARD MOLD-IN-COLOR INTERIOR COMPONENTS TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 00 2017 10 27 Released L. Schmalz, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 10 ASSEMBLY PERFORMANCE, HARD MOLD-IN-COLOR WSS-M15P4-H INTERIOR COMPONENTS 1. SCOPE This specification defines

2、 the minimum durability and performance requirements of hard, mold-in-color interior trim panels, moldings, overhead and floor consoles, and hard instrument panels where various materials are combined to provide a trim assembly having decorative and/or functional features. 2. APPLICATION This specif

3、ication was originally released for plastic mold-in-color and non-visible interior trim items such as door panels, center and overhead consoles, quarter panels, A-, B-, C-, and D-pillar moldings, hard instrument panels, instrument panel components and garnish molding. 2.1 LIMITATIONS Not applicable

4、for painted or wrapped parts. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification is performance based and does not have approved sources. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of

5、 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA Excluded from this specification are the non-resin components within the following assembly performance specifications; soft instrument pa

6、nels, interior soft trim and wrapped parts (WSS-M15P45-C/latest), package trays (WSS-M15P6-E/latest), steering wheels (WSS-M98P12-C1/latest), headliners (WSS-M15P27-G/latest), carpeted substrate (WSS-M8P16-B/latest), molded armrests and headrests (WSS-M15P20-B1/B2/latest), appliqus (WSS-M15P34-E/lat

7、est), visors (WSS-M98P3-C/latest), painted interior components (WSS-M2P188-B1/latest), chrome plated components (WSS-M1P83-E1/latest), interior elastomers (WSS-M9P8-C/latest), instrument clusters (WSS-M15P52-A) interior NVH components (WSS-M99P32-E1/latest) or whose performance is specified separate

8、ly. 3.4 DV/PV TEST PLAN PEC/FEC/PV testing must be conducted in compliance with program milestones unless otherwise specified by Ford Engineering. See Table 1 and 2 for DV/PV testing. Testing for mold-in-color components is detailed in Table 1 unless specified otherwise by Ford Engineering. Testing

9、for non-visible components is detailed in Table 2 unless otherwise specified by Ford Engineering. Testing must be done on parts unless part geometry does not allow. If that is the case, appropriate plaques with production grain and color can be used. ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Co

10、pyright 2017, Ford Global Technologies, LLC Page 2 of 11 3.5 APPEARANCE Color, gloss, grain, tactile effect shall match the approved Corporate Design master sample. 3.5.1 Gloss As released by Engineering: Gloss A: 20o Glossmeter min 92 B: 60o Glossmeter 76-84 C: 60o Glossmeter 66-74 D: 60o Glossmete

11、r 58-66 E: 60o Glossmeter 47-53 F: 60o Glossmeter 33-38 G: 60o Glossmeter 17-23 H: 60o Glossmeter 7-13 J: 60o Glossmeter 4-6 K: 60o Glossmeter 2-4 L: 60o Glossmeter 0.5-2.0 N: 60o Glossmeter 1.8-2.4 R: 60 Glossmeter 1.2-1.6 3.6 ENVIRONMENTAL TESTING Vehicle Location Examples of components Test Tempe

12、rature Horizontal or vertical parts AT OR ABOVE THE BELT-LINE Pillars; upper quarter panels; hard instrument panels and window garnish moldings 100 +/-2 C Horizontal or vertical parts BELOW THE BELT-LINE Door panels; lower quarter trim panels; floor and overhead consoles and glove box doors 90 +/-2

13、C Non-Sun Loaded Scuff plates and other non-sun loaded floor level parts 80 +/-2 C 3.6.1 Short Term Environmental Cycling (FLTM BO 040-01 Procedure A, XX C) Rating 4 min 3.6.2 Long Term Environmental (FLTM BO 040-01 Procedure B, XX C) Rating 4 min Note: For Upper A-Pillars: In addition to the measur

14、ement locations defined in FLTM BO 040-01, measurement locations should be every 5 centimeters starting at the upper zero location and running along the glass and the weather seal edges (See diagram below). Applies to paragraphs 3.6.1 and 3.6.2. ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyrig

15、ht 2017, Ford Global Technologies, LLC Page 3 of 11 Upper A-Pillars: For 3.6.1 Short Term Heat, Humidity, and Cold cycle: Within the last 2 hours of the final cycle of high heat, photograph the parts with the same camera angle as on the pre-test photo. For 3.6.2 Long Term heat: Within the last 24 ho

16、urs of high heat test, photograph the parts with the same camera angle as on the pre-test photo. Subject the number of assemblies specified to each of the cycles per paragraphs 3.6.1 and 3.6.2. Evaluation: The trimmed assemblies shall remain relatively unaffected by the exposure cycles during and af

17、ter the tests as demonstrated by: (1) Tactually/visually - no excessive tackiness, loss in surface-grain, or surface-color change (AATCC Procedure 1, Rating 4, min); no distortion, warping, blushing, hazing, milking, staining, waviness, or other objectionable visual appearance. (2) Functionally - no

18、 excessive expansion, shrinking, or warping that will interfere with normal functional operations. (3) Dimensionally - no movement exceeding 3.0 mm from the original installed position during or after the test; for the “significant characteristic locations“, no movement exceeding 0.5 mm from the ori

19、ginal installed position during or after the test. Dimensional exceptions to these requirements may be allowed on the Engineering drawing. 3.7 IMPACT RESISTANCE- ROOM TEMPERATURE (23 +/-2 C) Required for scuff plates, floor consoles, load floors, seating components, door map pockets or any other par

20、ts as required by Ford Engineering. Rubber Ball, 4.5 kg weight, 127 mm diameter, 60 +/- 5 Durometer “A“ Test Method: Conduct this test with the trim assembly mounted on an actual or simulated production support foundation using the approved retention methods. Drop the rubber ball from the height spe

21、cified below at the impact locations indicated on the Engineering Drawing. Drop Height ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 4 of 11 Scuff Plates 610 mm Load Floor 500 mm Below belt line 460 mm Above the belt line 305 mm Console 305 mm The

22、assembly shall show no evidence of cracking or breaking and shall fully recover from indentation. 3.8 RESISTANCE TO INTERIOR WEATHERING (FLTM BO 116-01, AATCC Evaluation Procedure 1) In Vehicle Sunlight Exposure Level FLTM BO 116-01 Test Exposure AATCC Rating After Exposure, min. Severe Exposure: In

23、strument panel top, defroster grille, 3609.6 kJ/m2 Rating 4 Heavy Exposure: Instrument panel lower top cover, 2 tone IP, IP bezel, IP registers, airbag, steering wheel, message center, appliqus, parcel shelf assembly/package tray and center finish panel, door trim top rollover 2406.4 kJ/m2 Rating 4

24、Medium Exposure: Instrument panel lower, door trim, interior trim, pillars/grab handles, garnish moldings, seat back plastics, head rest plastics, sunshade, sun visor, seat belt webbing resins that come in contact with the vinyl and/or foam. 3.15 DETERMINATION OF 90 DEGREE PEEL AND ADHESIVE STRENGTH

25、 (not for wrapped applications) (FLTM BN 151-06, minimum average) 3.15.1 Initial Adhesive Strength 0.48 N/mm width 3.15.2 Adhesive Strength after Long Term Heat Exposure 75% of initial (para 3.6.2) result, no visual change in appearance 3.15.3 Adhesive Strength after Short Term Heat, Humidity 75% of

26、 initial result, And Cold Cycle no visual change in (para 3.6.1) appearance Note: For adhesively bonded badges and emblems test parts in assembly 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contac

27、t for questions concerning Engineering Material Specifications. Rubber Ball Contact Information Dave Clow, Schap Specialty Machine, Inc. 17309 Taft Street Spring Lake, MI 49456, USA Phone:1-616-846-6530 4.1 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an

28、 expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the require

29、ments of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing)

30、 with Ford. 4.2 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 7 of 11 Prior to making any changes t

31、o the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by

32、submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign of

33、f must be kept until Job 1. 4.3 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is up

34、dated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 8 of 11 TABLE 1 TESTING REQUIREMENTS Sampl

35、e size/color (For Ford approved resins only) New Color Approved Resins (Data from MCDCC approval can be used as surrogate for part testing) MCDCC requirements for Non Ford approved resins (Material is not listed on the ASL. Each color must be tested) DV Required for New part geometry or new material

36、 Technology (post FDJ) PV Must use production tools Molder/resin supplier change Comments Components 3.5 Appearance All colors X X X 3.6.1 Short Term Heat Exposure 1/part- darkest color 2 parts/new technology X X Required in assembly X * *Key life testing can be used in lieu. Bonded parts must be pr

37、oduction representative. 3.6.2 Long Term Heat Exposure 1/part-darkest color 2 parts/new technology X X Required in assembly X * For IP-Sunload testing per IP-105. Bonded parts must be production representative. 3.7 Impact Resistance-Room Temp 2/parts lightest and darkest color X X Required in assemb

38、ly Grained Plaque/Part tests 3.9 Soiling and Cleanability* 1 per media/ per grain/per color X X X Production intent resin, grain and colorant to complete testing by FEC for all new colors and grains Concentrate letdown ratio must be production representative 3.10.1 Scratch and Mar Resistance* 3 per

39、grain/per color X X Testing on plaques with Production intent resin, grain and color (with production intent X Testing on production parts if they differ in grain, material, color and/or processing from Concentrate letdown ratio must be production representative ENGINEERING MATERIAL SPECIFICATION WS

40、S-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 9 of 11 Sample size/color (For Ford approved resins only) New Color Approved Resins (Data from MCDCC approval can be used as surrogate for part testing) MCDCC requirements for Non Ford approved resins (Material is not listed on the ASL. Ea

41、ch color must be tested) DV Required for New part geometry or new material Technology (post FDJ) PV Must use production tools Molder/resin supplier change Comments colorant) if available plaques tested at DV or if unavailable at DV. 3.10.2 Micro Scratch (A/B gloss only) 3 per color X X X Testing on

42、plaques with Production intent resin, grain and color (with production intent colorant) if available X Testing on production parts if they differ in grain, material, color and/or processing from plaques tested at DV or if unavailable at DV. Material Tests (ungrained/ grained parts or plaques) 3.8 Re

43、sistance to Interior Weathering 1 per color X X X Production intent resin and colorant to complete testing by PEC MCDCC form may be used as evidence Concentrate letdown ratio must be production representative 3.8.1 Tackiness of Interior Materials after Weathering 1 per color X X X Production intent

44、resin and colorant to complete testing by PEC MCDCC form may be used as evidence Concentrate letdown ratio must be production representative 3.11 Fogging 1 any color X X Contact ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 10 of 11 Sample size/col

45、or (For Ford approved resins only) New Color Approved Resins (Data from MCDCC approval can be used as surrogate for part testing) MCDCC requirements for Non Ford approved resins (Material is not listed on the ASL. Each color must be tested) DV Required for New part geometry or new material Technolog

46、y (post FDJ) PV Must use production tools Molder/resin supplier change Comments Prototype parts Materials Engineering if surrogate data is acceptable 3.12 Odor 1/condition any color X X Prototype parts Contact Materials Engineering if surrogate data is acceptable. 3.13 Flammability 5 specimens X X X

47、 Production intent resin to complete testing by FEC X Certified at PPAP and annually. Testing is dependent on part size (355x100 mm min). FMVSS 302 can be used as surrogate 3.14 Environmental Stress Cracking 1 component any color X X Prototype parts or plaques Required for all amorphous materials th

48、at come in continuous contact with grease, oil etc. 3.15 90 Degree Peel Adhesion Strength 3 any color X *As agreed upon by Ford Design Otherwise, PV testing must be run.ENGINEERING MATERIAL SPECIFICATION WSS-M15P4-H Copyright 2017, Ford Global Technologies, LLC Page 11 of 11 Table 2 TESTING REQUIREM

49、ENTS FOR NON-VISIBLE COMPONENTS Component Tests Sample Size Non-Visible Application Requirements Comments 3.6.1 Short Term Heat Exposure 1/part DV *Key life testing can be used in lieu. Bonded parts must be production representative. 3.6.2 Long Term Heat Exposure 1/part DV For IP-Sunload testing per IP-105. Bonded parts must be production representative. 3.11 Fogging 1 part DV Contact Materials Engineering if surrogate data is acceptable. 3.12 Odor 1/condition DV Contact