FORD WSS-M1H1061-A-2018 FABRIC DINAMICA MICROFIBER NON WOVEN UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 01 2018 02 09 Reviewed Technical Review Compete No changes needed D. Murtonen, NA 2008 10 22 Activated M. Montgomery, FOE Controlled document at www.MATS Copyright 2018, Ford Global Technologies, LLC Page 1 of 2 FABRIC, DINAMICA, MICROFIB

2、ER, NON WOVEN WSS-M1H1061-A UNLAMINATED 1. SCOPE The material defined by this specification is a Non Woven Polyester Microfiber face fabric. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for use in the 2008 C307 RS Program. Limitations: The fa

3、bric is not recommended for heavy trucks and commercial vehicles. 3. REQUIREMENTS In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4 as applicable. 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sourc

4、es identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 FABRIC CONSTRUCTION 3.2.1 Fabric Wei

5、ght, +/- 5% (FLTM BN 106-01) 300 g/m2 3.3 COMPOSITION (ASTM D 629) Polyester: 92% +/- 1% Polyurethane: 8% +/- 1% 3.4 YARN COMPOSITION (ASTM D 1244) Face : Micro Fiber 100% Polyester 0.15 denier (140 g/m2) Scrim :100% Polyester 150 denier (95 g/m2) Backing : FR polyester 0.5 denier 90% , Microfiber P

6、olyester 0.15 denier 10% (total : 61 g/m2) Recycled content : Face 100% PCR Fiber; Back 10% PCR Fiber ENGINEERING MATERIAL SPECIFICATION WSS-M1H1061-A Copyright 2018, Ford Global Technologies, LLC Page 2 of 2 3.5 METHOD OF DYEING Piece Dyed 3.5.1 Types of Dyes Disperse Dyestuff 3.6 FINISHED OPERATIO

7、NS 3.6.1 Anti-Stain and Water Repellent Finishing 3.6.2 Surface Impregnation Treatment Dipping: Weight 4 g/m2 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineeri

8、ng Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. 4.2 Minimum finished width 137cm Maximum finished width 142 cm 4.3 APPROVAL OF MATERIALS Suppliers desiring ap

9、proval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, dem

10、onstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects

11、Analysis, Control Plans, Certification testing) with Ford. 4.4 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such cha

12、nges affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering

13、 Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.5 RESTRICTED SUBSTANCE MANAGE

14、MENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS