FORD WSS-M1H1126-A11-2017 FABRIC BELGRANO PATTERN WARP KNIT FABRIC BELGRANO PATTERN WARP KNIT TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2017 03 13 Released B. Andrews, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 FABRIC, BELGRANO PATTERN, WARP KNIT, WSS-M1H1126-A11 VIRGIN WITH SOIL REPELLANT 1. SCOPE The material defined

2、by this specification is a warp knit polyester face fabric made from virgin yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for Expedition 2018 MY seat bolster. The fabric was originally approved as bi-laminated with foam and scrim. 3. REQ

3、UIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford a

4、t or available externally through a Ford Materials Engineer. 3.2 APPPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-B1/B2/B3/B4/

5、latest as applicable. 3.4 VEHICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest, Performance, Vehicle Interior Environmental Quality Material/Component Requirements. Data must be included in material submissio

6、n package. 3.5 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after remo

7、val. 3.6 FABRIC CONSTRUCTION 3.6.1 Fabric Count, -/+5 % tolerance (ASTM D3775) Wales 126 / 10 cm Courses 173 / 10 cm ENGINEERING MATERIAL SPECIFICATION WSS-M1H1126-A11 Copyright 2017, Ford Global Technologies, LLC Page 2 of 3 3.6.2 Fabric Weight, -/+5 % tolerance 284 g/m2 (FLTM BN 106-01) 3.7 COMPOS

8、ITION (ASTM D629) Fabric 100% polyester 3.8 YARN CONSTRUCTION (ASTM D1244) Face 44 Dtex f24 (semi dull, round, polyester) Middle 167 Dtex f34 (semi dull, round, polyester) Back 44 Dtex f36 (semi dull, round, polyester) 4th 44 Dtex f24 (semi dull, round, polyester) 3.9 METHOD OF DYEING Piece Dyed 3.1

9、0 FINISHED OPERATIONS Pulldown, Dye, Soil Repellent Finish, Heatset, Inspect, Pack Any changes to the above process must be approved by Materials Engineering. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specifica

10、tion. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or Regional duplication, eac

11、h regional location of the supplier for this specification must provide a Construction package and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirements of WSS-M

12、8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Mate

13、rials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available f

14、or review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalen

15、t in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1126-A11 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 Prior to making any changes to the material originally approved, whether or not such changes affect the ma

16、terials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. F

17、or parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Producation Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Sub

18、stance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS