FORD WSS-M1H1249-A11-2015 FABRIC BEVEL PATTERN FLAT WOVEN 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2015 11 11 Released R. Kyle, EU Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 3 FABRIC, BEVEL PATTERN, FLAT WOVEN, WSS-M1H1249-A11 100% VIRGIN WITH SOIL REPELLANT 1. SCOPE The material defined

2、is a flat woven polyester face fabric made from 100% virgin yarn with soil repellent. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for MY2016 Transit seat bolster. The fabric was originally approved as tri-laminated with foam and a backing sc

3、rim. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located wi

4、thin Ford at or available externally through a Ford Materials Engineer. 3.2 This specification is based on virgin materials with soil repellent. 3.3 FABRIC PERFORMANCE In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4/latest as applicable

5、. 3.4 APPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.5 VEHICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest, Performance, Vehicle Interior Environmental Q

6、uality Material/Component Requirements. Data must be included in material submission package. 3.6 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Test

7、ing of the material should occur in the conditioning environment or soon after removal. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1249-A11 Copyright 2015, Ford Global Technologies, LLC Page 2 of 3 3.7 FABRIC CONSTRUCTION 3.6.1 Fabric Count, - /+5 % tolerance (ASTM D3775) Warp 151 / 10 cm Fill 127 /

8、10 cm 3.6.2 Fabric Weight, -/+5 % tolerance 320 g/m2 (FLTM BN 106-01) 3.8 COMPOSITION (ASTM D629) Fabric 100% polyester 3.9 YARN CONSTRUCTION (ASTM D1244) Warp (A) 1100 Dtex f216 ( polyester, air texturized yarn) Weft (B) 1100 Dtex f216 (polyester, air texturized yarn) 3.10 METHOD OF DYEING Solution

9、 dyed 3.11 FINISHED OPERATIONS Washing, drying, framing. Any changes to the above process must be approved by Materials Engineering 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for question

10、s concerning Engineering Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or regional duplication, each regional location of the

11、supplier for this specification must provide a construction package and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirements of WSS-M8P18-A1/A2/A3/A4/latest. 4.

12、3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supp

13、lier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material ENGINEERING MATERIAL SPECIFICATION WSS-M1H1249-A11 Copyright 2015, Ford Global Techno

14、logies, LLC Page 3 of 3 Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testin

15、g) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the

16、 specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components usi

17、ng Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Producation Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed

18、 by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS