FORD WSS-M2C213-A1-2015 OIL ENGINE SAE 5W-30 INITIAL AND SERVICE FILL TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2015 03 20 Released E.Celebi, EU Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 10 OIL, ENGINE, SAE 5W-30, INITIAL AND SERVICE FILL WSS-M2C213-A1 1. SCOPE This material specification defines the

2、 minimum acceptable performance requirements and physical/chemical properties of engine oils to be used by Ford Otosan in its worldwide engine/vehicle manufacturing operations. 2. APPLICATION This specification will be released for initial fill engine oils used for lubrication of heavy-duty compress

3、ion ignition engines using diesel fuels. The specification will also be used to define engine oils for servicing Ford heavy-duty engines where applicable. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Re

4、quirements For Production Materials (WSS-M99P1111-A). 3.2 PERFORMANCE Shall meet all the requirements of “ACEA European Oil Sequences E6-12 Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _ _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _ _ _ N _ _ _ _ _ B _ _ _

5、 _ _ Cu _ _ _ _ _ Cl _ _ _ _ _ Sulfated Ash _ _ _ _ _ IV. Tests Conducted _ _ _ _ _ Comments: _ _ _ _ _ Signature_ Title _ ENGINEERING MATERIAL SPECIFICATION WSS-M2C213-A1 Copyright 2015, Ford Global Technologies, LLC. Page 9 of 10 (Supplement A / Page 6 of 6) Oil Company:_ Date: _ Product Name:_ Pr

6、oduct Code: _ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 150 C (ASTM D445), mm2/s report _ _ Viscosity at 100 C (ASTM D445), mm2/s 9.3-.001%) report _ _ Turbocharger deposits (MTV 5040) (DIN 51535), mg. 90 max _ _ Signature_ Title _ ENGINEERING MATE

7、RIAL SPECIFICATION WSS-M2C213-A1 Copyright 2015, Ford Global Technologies, LLC. Page 10 of 10 (Supplement B Page 1 of 1) Oil Company:_ Date: _ Product Name:_ Blend Location:_ Product Code: _ Quality Control Certification Physical/Chemical Properties Approved Limits Frequency Viscosity at 150 C (ASTM

8、 D445), mm2/s _ _ Viscosity at 100 C (ASTM D445), mm2/s _ _ Viscosity at 40 C (ASTM D445), mm2/s _ _ Density (ASTM D1298), kg/L _ _ Viscosity at 30 C (ASTM D5293), mPa.s _ _ Low Temp. Pumping Viscosity at -35 C, mPa.s _ _ (ASTM D4684) _ _ Pour Point (ASTM D97), C _ _ Flash Point (ASTM D93), C _ _ Vo

9、latility Evap. Loss, 1 h at 250 C (ASTM D5800), % _ _ Shear Stability (ASTM D 445), mm2/s at 100 C after 90 cycles measured at 100 C, (ASTM D6278) or CEC L-14-A-93 _ _ Viscosity at 150 C and 106 s-1 (ASTM D 4683 or CEC L-36-A-97), mPa.s _ _ Copper Corrosion (ASTM D 130, 3 h at 100 C) _ _ Foaming Ten

10、dency (ASTM D892) without Option A Sequence I, mL _ _ Sequence II, mL _ _ Sequence III, mL _ _ High Temperature Foaming (ASTM D6082), mL _ _ PDSC (CEC-L-85T-99), minutes _ _ HTCBT (135C) corrosion, used oil Pb, ppm _ _ Total Acid Number (ASTM D664), mg KOH/g _ _ Total Base Number (ASTM D2896), mg KO

11、H/g _ _ Total Base Number (ASTM D4739), mg KOH/g _ _ Sulfated Ash (ASTM D874), % _ _ Elemental Mass (D5185) Phosphorus content, % _ _ Barium, % _ _ Boron, % _ _ Calcium, % _ _ Chlorine, % _ _ Copper, % _ _ Magnesium, % _ _ Molybdenum, % _ _ Nitrogen, % _ _ Potassium, % _ _ Sodium, % _ _ Sulfur, % _ _ Zinc, % _ _ Other (.001%) _ _ Signature_ Title _