FORD WSS-M2C215-A1-2015 OIL ENGINE SAE 10W-40 INITIAL AND SERVICE FILL TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2015 07 31 Released E.Celebi, EU Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 11 OIL, ENGINE, SAE 10W-40, INITIAL AND SERVICE FILL WSS-M2C215-A1 1. SCOPE This material specification defines th

2、e minimum acceptable performance requirements and physical/chemical properties of engine oils to be used by Ford Otosan in its worldwide engine/vehicle manufacturing operations. 2. APPLICATION This specification will be released for initial fill engine oils used for lubrication of heavy-duty compres

3、sion ignition engines using diesel fuels. The specification will also be used to define engine oils for servicing Ford heavy-duty engines where applicable. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved S

4、ource List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material c

5、onditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE Shall meet all the requirements of “ACEA European Oil Sequences E6

6、-12 Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _ _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _ _ _ N _ _ _ _ _ B _ _ _ _ _ Cu _ _ _ _ _ Cl _ _ _ _ _ Sulfated Ash _ _ _ _ _ IV. Tests Conducted _ _ _ _ _ Comments: _ _ _ _ _ Signature_ Title _ ENGINEERING M

7、ATERIAL SPECIFICATION WSS-M2C215-A1 Copyright 2015, Ford Global Technologies, LLC. Page 10 of 11 (Supplement A / Page 6 of 6) Oil Company:_ Date: _ Product Name:_ Product Code: _ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 150 C (ASTM D445), mm2/s re

8、port _ _ Viscosity at 100 C (ASTM D445), mm2/s 12.5-.001%) report _ _ Turbocharger deposits (MTV 5040) (DIN 51535), mg. 90 max _ _ Signature_ Title _ ENGINEERING MATERIAL SPECIFICATION WSS-M2C215-A1 Copyright 2015, Ford Global Technologies, LLC. Page 11 of 11 (Supplement B Page 1 of 1) Oil Company:_

9、 Date: _ Product Name:_ Blend Location:_ Product Code: _ Quality Control Certification Physical/Chemical Properties Approved Limits Frequency Viscosity at 150 C (ASTM D445), mm2/s _ _ Viscosity at 100 C (ASTM D445), mm2/s _ _ Viscosity at 40 C (ASTM D445), mm2/s _ _ Density (ASTM D1298), kg/L _ _ Vi

10、scosity at 25 C (ASTM D5293), mPa.s _ _ Low Temp. Pumping Viscosity at -30 C, mPa.s _ _ (ASTM D4684) _ _ Pour Point (ASTM D97), C _ _ Flash Point (ASTM D93), C _ _ Volatility Evap. Loss, 1 h at 250 C (ASTM D5800), % _ _ Shear Stability (ASTM D 445), mm2/s at 100 C after 90 cycles measured at 100 C,

11、(ASTM D6278) or CEC L-14-A-93 _ _ Viscosity at 150 C and 106 s-1 (ASTM D 4683 or CEC L-36-A-97), mPa.s _ _ Copper Corrosion (ASTM D 130, 3 h at 100 C) _ _ Foaming Tendency (ASTM D892) without Option A Sequence I, mL _ _ Sequence II, mL _ _ Sequence III, mL _ _ High Temperature Foaming (ASTM D6082),

12、mL _ _ PDSC (CEC-L-85T-99), minutes _ _ HTCBT (135C) corrosion, used oil Pb, ppm _ _ Total Acid Number (ASTM D664), mg KOH/g _ _ Total Base Number (ASTM D2896), mg KOH/g _ _ Total Base Number (ASTM D4739), mg KOH/g _ _ Sulfated Ash (ASTM D874), % _ _ Elemental Mass (D5185) Phosphorus content, % _ _ Barium, % _ _ Boron, % _ _ Calcium, % _ _ Chlorine, % _ _ Copper, % _ _ Magnesium, % _ _ Molybdenum, % _ _ Nitrogen, % _ _ Potassium, % _ _ Sodium, % _ _ Sulfur, % _ _ Zinc, % _ _ Other (.001%) _ _ Signature_ Title _