FORD WSS-M2C948-B-2014 OIL ENGINE SERVICE FILL SAE 5W-20 TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 1 2014 10 30 Revised See Summary of Revisions R. Haigh, EU 2011 08 22 Activated R Haigh, EU Controlled document at www.MATS Copyright 2014, Ford Global Technologies, Inc. Page 1 of 14 OIL, ENGINE, SERVICE FILL SAE 5W-20 WSS-M2C948-B 1. S

2、COPE These material specifications defined the minimum acceptable performance requirements and physical/chemical properties of engine oils to be used by Ford Motor Company in its worldwide engine/vehicle manufacturing operations. 2. APPLICATION These specifications are released in Europe for initial

3、 fill engine oils used for lubrication of spark ignition engines using gasoline. The Section 3.1 titled STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS applies only to engine oils supplied directly to Ford Motor Company and / or its affiliates. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION

4、 MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 PERFORMANCE 3.2.1 General Test Requirements Where applicable, the required engine tests shall be conducted in accordance with the most recently approved

5、procedures as described in the ACEA C2-10 or A5/B5-10 Sequences. All tests under surveillance by ASTM must be conducted using test equipment monitored by and calibrated to the requirements of the ASTM Test Monitoring Center. All engine performance testing used to support a claim of compliance with t

6、he ACEA sequences must be generated according to the EELQMS. Suppliers must demonstrate commitment to comply with the ATIEL Code of Practice. 3.2.2 ACEA Seq 2.1, High Temperature Deposits, Ring Sticking, Oil Thickening To meet or exceed the requirements of ACEA C2, when tested in accordance with CEC

7、-L-088-02, (TU5JP-L4) 72 Hour Test. 3.2.3 ACEA Seq 2.2, Low Temperature Sludge To meet or exceed the requirements of ACEA C2, when tested in accordance with ASTM D6593-00 (Sequence VG), under protocol Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _

8、 _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _ _ _ N _ _ _ _ _ B _ _ _ _ _ Cu _ _ _ _ _ Cl _ _ _ _ _ Sulphated Ash _ _ _ _ _ V. Tests Conducted _ _ _ _ _ Comments: _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATION WSS-M2C948-B Controlled document at www.MATS Copyright 2014, Ford Global Technolog

9、ies, Inc. Page 11 of 14 (Supplement A, p. 6 of 7) Oil Company_ Date_ Product Name_ Viscosity Grade_ Product Code_ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 150 C (ASTM D 445), mm2/s report _ _ Viscosity at 100 C (ASTM D 445), mm2/s 7.0-.001%) repor

10、t _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATION WSS-M2C948-B Controlled document at www.MATS Copyright 2014, Ford Global Technologies, Inc. Page 13 of 14 (Supplement B, p. 1 of 2) Oil Company_ Date_ Product Name_ Viscosity Grade_ Product Code_ Quality Control Certification Physical/Chemic

11、al Properties Approved Limits Frequency Test Results Viscosity at 150 C (ASTM D 445), mm2/s _ _ Viscosity at 100 C (ASTM D 445), mm2/s _ _ Viscosity at 40 C (ASTM D 445), mm2/s _ _ Density (ASTM D 1298), kg/L _ _ Viscosity at -25 C (ASTM D 5293), mPa.s _ _ Viscosity at -30 C (ASTM D 5293), mPa.s _ _

12、 Low Temp. Pumping Viscosity at -30 C, mPa.s _ _ (ASTM D 4684) at -35 C, mPa.s _ _ Pour Point (ASTM D 97), C _ _ Stable Pour Point (SAE J 300 App. B), C _ _ Gelation Index (ASTM D 5133) _ _ Flash Point (ASTM D 93), C _ _ Volatility Evap. Loss, 1 h at 250 C (ASTM D 5800), % _ _ Shear Stability (ASTM

13、D 445), mm2/s at 100 C After ASTM D 6278 or CEC L-14-A-93 _ _ Viscosity at 150 C and 106 s-1 CEC L-36-A-90, mPa.s New Oil _ _ After ASTM D 6278 or CEC L-14-A-93 _ _ Copper Corrosion (ASTM D 130, 3 h at 100 C) _ _ Filterability (ASTM D 6795), % flow reduction, max _ _ Water Tolerance (ASTM D 6794), %

14、 _ _ Foaming (ASTM D 892) without Option A Sequence I, mL _ _ Sequence II, mL _ _ Sequence III, mL _ _ High Temperature Foaming (ASTM D6082), mL _ _ Total Acid Number (ASTM D 664), mg KOH/g _ _ Total Base Number (ASTM D 2896), mg KOH/g _ _ Sulfated Ash (ASTM D 874), % _ _ Cleanliness Max Particle Si

15、ze (Initial Fill only) _ _ Cleanliness Particle Count 4 microns _ _ Cleanliness Particle Count 6 microns _ _ Cleanliness Particle Count 14 microns _ _ Visual Appearance _ _ Phosphorus content, % _ _ Barium, % _ _ Boron, % _ _ Calcium, % _ _ Chlorine, % _ _ Copper, % _ _ Magnesium, % _ _ Molybdenum,

16、% _ _ Nitrogen, % _ _ Potassium, % _ _ Silicon, % _ _ Sodium, % _ _ Sulphur, _ _ ENGINEERING MATERIAL SPECIFICATION WSS-M2C948-B Controlled document at www.MATS Copyright 2014, Ford Global Technologies, Inc. Page 14 of 14 (Supplement B, p. 2 of 2) Physical/Chemical Properties Approved Limits Frequency Test Results Zinc, % _ _ Other (.001%) _ _ Signature_ Title_ MaterialsEngineering Concurrence_