FORD WSS-M3H105-A8-2008 CARPET POLYESTER FLAT NEEDLED LATEX PRECOAT POLYETHYLENE BACKCOATED - TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯背涂的带乳胶预涂层的扁平针刺聚酯地毯 与标准FORD WSS-M99P1111-A一起.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes Rev. 2 2008 11 03 N-STATUS Replaced by WSS-M15P32-C L. Sinclair, FNA 1999 02 02 Activated L. Daniv-Zarewych WP 3948-a Page 1 of 4 CARPET, POLYESTER, FLAT NEEDLED, WSS-M3H105-A8 LATEX PRECOAT, POLYETHYLENE BACK

2、COATED NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by this specification are flat needled, polyester, non-woven carpets of good quality and uniform composition. 2. APPLICATION This specification was originally released for materials used for trunk covering material for the 1999 1/2

3、Ford Focus. 3. REQUIREMENTS In addition to the requirements listed herein, the end-item carpet assembly (molded or otherwise fabricated), shall meet all requirements of the WSS-M15P32-C performance specification. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to Q

4、uality System Requirements, QS-9000. Material specification requirements are to be used for initial qualification of materials. A Control Plan for ongoing production verification is required. This plan must be reviewed and approved by the relevant Ford Materials activity and/or Ford Supplier Technic

5、al Assistance (STA) prior to production parts submission. Appropriate statistical tools must be used to analyze process/product data and assure consistent processing of the materials. Part producers using this material in their products, must use Ford approved materials and must conform to a process

6、 control plan which has been approved by STA and/or the relevant Materials Activity. ENGINEERING MATERIAL SPECIFICATION WSS-M3H105-A8 WP 3948-b Page 2 of 4 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS Ford Motor Company, at its option, may conduct infrared and/or thermal analysis of materi

7、al/parts supplied to this specification. The IR spectra and thermograms established for initial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference stan

8、dard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions u

9、nless otherwise specified. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from production representative carpet. 3.5 COMPOSITION (ASTM D 276) Fiber 100 % Polyester Pre-coat Latex Backcoating Polyethylene -LDPE 3.6 METHOD OF DYEING Solution dyed or equivalent 3.7 CONS

10、TRUCTION 3.7.1 Fiber Size and Description 5 dtex/ 18 dtex (ASTM D 1244) (polyester) 3.7.2 Thickness, range 1.75 - 2.55 mm (ASTM D 418) ENGINEERING MATERIAL SPECIFICATION WSS-M3H105-A8 WP 3948-b Page 3 of 4 3.8 Weight, min (FLTM BN 106-01) Pile Fiber 210 - 290 g/m2 Pre-coat 45 - 55 g/m2 Backcoating 6

11、5 - 135 g/m2 Total 320 - 480 g/m2 3.9 PHYSICAL PROPERTIES 3.9.1 Shrinkage, max. 1.5% (FLTM BN 105-01) 3.9.2 Breaking Strength, min. (ASTM D5034, Grab Method, 305 mm/minute jaw speed) MD 555 N AMD 685 N 3.10 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in a

12、ll characteristics to the material upon which approval was originally granted. Prior to making any change in the properties, composition, construction, color, processing or labeling of the material originally approved under this specification, whether or not such changes affect the materials ability

13、 to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of the proposed changes and obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be sub

14、mitted with the request. Substance restrictions imposed by law, regulations or Ford, apply to the materials addressed by this document. The regulations are defined in Engineering Materials Specification WSS-M99P9999-A1. ENGINEERING MATERIAL SPECIFICATION WSS-M3H105-A8 WP 3948-b Page 4 of 4 4. APPROV

15、AL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affected Purchasing, Design and Materials Engineering activity. Upo

16、n request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification (test results

17、, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessment of suitability for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List.