FORD WSS-M3H146-A-2011 CARPET BCF NYLON 6 6 CUT PILE 814 g m2 (24 oz) TO BE USED WITH FORD WSS-M99P1111-A 《溴氯二氟甲烷6 6割绒814 g m2(24 oz)的地毯 与福特WSS-M99P1111-A 一起使用》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev.1 2011 03 01 N Status FCSD Release only, does not follow GCPB Strategy L. Sinclair, FNA 2010 11 16 Activated L. Sinclair, NA Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 1 of 4 CARPET, BCF NYLON 6/6,

2、CUT PILE, WSS-M3H146-A 814 g/m2 (24 oz) NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by this specification are fine denier, bulked continuous filament (BCF) nylon, cut pile carpets, tufted into a synthetic primary foundation. The mat may be backed with either rubber or other material

3、. 2. APPLICATION This material was originally released for floor mats. 3. REQUIREMENTS In addition to the requirements listed herein, the end-item mat assembly shall be tested to WSS-M15P44-B and any additional SDS requirements. The details for each of the suppliers specific construction shall be do

4、cumented in the supplement attached and uploaded into the FMD (Ford Materials Database). 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 SAMPLE SELECTION All eva

5、luations shall be conducted on test specimens taken from finished mat assemblies. 3.3 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.4 COMPOSITION (ASTM D 276) 3.4.1 Pile Yarn 100

6、% Nylon 6/6 3.4.2 Primary Foundation Polyester 3.4.3 Back Coating Report* ENGINEERING MATERIAL SPECIFICATION WSS-M3H146-A Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 2 of 4 3.4.4 Pre Coat Report * 3.4.5 Secondary Foundation Report * 3.4.6 Secondary Backing Repo

7、rt * * Materials approved for each suppliers construction can be found in the FMD (Ford Material Database). 3.5 CONSTRUCTION 3.5.1 Pile Yarn 1400 Denier (ASTM D 1244) 3.5.2 Pile Count (ASTM D 418) Rows/100 mm 39 Stitches/100 mm 57 typical* Rows and stitches per 100 mm shall be based on an average co

8、unt on a 254 mm length of carpet and shall not exceed the tolerance provided on the approved construction supplement in the FMD for the approved material. * Stitches approved for each suppliers construction can be found in the FMD (Ford Material Database). 3.5.3 Needle Gauge 2.5 mm 3.6 THICKNESS 3.6

9、.1 Pile Height 8.0 mm Nominal (ISO 1765) Pile Height tolerances approved for each suppliers construction can be found in the FMD (Ford Material Database). 3.6.2 Primary Foundation Thickness Report * 3.6.3 Back Coating Thickness Report * The back coating shall thoroughly saturate the base of the pile

10、 fiber bundles to ensure adequate tuft lock. Penetration of the back coating through to the face shall be controlled to provide the required resistance to abrasion and fiber loss, but it shall not be visible on the face of the pile fiber. 3.6.4 Pre Coat Thickness Report * 3.6.5 Secondary Foundation

11、Thickness Report * 3.6.6 Secondary Backing Thickness Report * * Thicknesses and tolerances approved for each suppliers construction can be found in the FMD (Ford Material Database). ENGINEERING MATERIAL SPECIFICATION WSS-M3H146-A Printed copies are uncontrolled Copyright 2011, Ford Global Technologi

12、es, LLC Page 3 of 4 3.7 WEIGHT, g/m2 (oz) (ASTM D 418/FLTM AN 102-02) 3.7.1 Pile Yarn 814 g/m2 (24oz) Nominal 3.7.2 Primary Foundation 120 g/m2 (3.5 oz) Nominal 3.7.3 Back Coating Report * 3.7.4 Pre Coat Report * 3.7.5 Secondary Foundation Report * 3.7.6 Secondary Backing Report * * Weights and tole

13、rances approved for each suppliers construction can be found in the FMD (Ford Material Database). 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 DRAWING CALL OUT The following shall be called out

14、on the Engineering drawing to correctly designate the approved material. WSS-M3H146-A Supplier Name and Product Code WSS-M15P44-B ENGINEERING MATERIAL SPECIFICATION WSS-M3H146-A Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 4 of 4 Floor Mat Construction Supplemen

15、t Supplier _Supplier Contact Name_ Number _ Product Name _ Supplier Rubber Grade _ Supplier Product Code _ Performance Specification _ Supplier Lab Number _ Supplier Lab Date _ Manufacturing Location _ Composition Type Supplier Pile Yarn ASTM D276 _ _ Primary Foundation ASTM D276 _ _ Back Coating (r

16、ubber) ASTM D276 _ _ Pre Coat ASTM D276 _ _ Secondary Foundation ASTM D276 _ _ Secondary Backing ASTM D276 _ _ Construction Solution or piece dyed (circle one) Please provide the following thermal data on the rubber backing: FTIR (ASTM E1252) _ DSC (ASTM D1356/D3418) _ TGA (ASTM E1131) _ Pile Yarn A

17、STM D1244 _ Denier Pile Count ASTM D5793 _+/- _ binding sites/ 100 mm length _+/- _binding sites/100 mm width Needle Gauge _ mm Pile Thickness ASTM D6859 _+/- _ mm Primary Thickness ASTM D6859 _+/- _ mm Back Coating Thickness ASTM D6859 _+/- _ mm Pre Coat Thickness ASTM D6859 _+/- _ mm Secondary Thi

18、ckness ASTM D6859 _+/- _ mm Secondary Backing Thickness ASTM D6859 _+/- _ mm Mass per Unit Area Weight Pile Yarn ASTM D5848 _+/- _ g/m2 Primary Foundation ASTM D5848 _+/- _ g/m2 Back Coating (rubber) ASTM D5848 _+/- _ g/m2 Pre Coat ASTM D5848 _+/- _ g/m2 Secondary Foundation ASTM D5848 _+/- _ g/m2 Secondary Backing ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Design Verification _ Production Verification _