FORD WSS-M3H150-A-2015 CARPET BCF NYLON 6 6 LOOPED PATTERN 713 g m2 (21 oz) TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 1 2015 05 08 Revised See Summary of Revisions L. Sinclair, NA 2014 02 03 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of 4 CARPET, BCF NYLON 6/6, LOOPED, WSS-M3H150-A PATTE

2、RN, 713 g/m2 (21 oz) 1. SCOPE The materials defined by this specification are fine denier, bulked continuous filament (BCF) nylon, looped pile carpets, in a synthetic primary foundation. The mat may be backed with either rubber or other material. 2. APPLICATION This material was originally released

3、for floor mats for anniversary or specialty edition vehicles. 2.1 LIMITATIONS Model year 2016 and beyond compression molding is not allowed to marry the face to backing material or to pull any B side features. Compression molding is only allowed as a secondary process to change geometry (3D shape).

4、3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1.1 In addition to the requirements listed herein, the end-item mat assembly shall be tested to WSS

5、-M15P44-B and any additional SDS requirements. The details for each of the suppliers specific construction shall be documented in the supplement attached and uploaded into the FMD (Ford Materials Database). 3.1.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Mater

6、ials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1. Data must be included in material submission package. 3.2 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished mat assemblies. 3.3 APPEARANCE (FLTM BI 109-01) The color, pa

7、ttern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.4 COMPOSITION 3.4.1 Pile Yarn 100% Nylon 6/6 (ASTM D 276) ENGINEERING MATERIAL SPECIFICATION WSS-M3H150-A Copyright 2015, Ford Global Technologies, LLC Page 2 of 4 3.4.2 Pri

8、mary Foundation Polypropylene (ASTM D 276) 3.4.3 Back Coating Report* (ASTM D 276) 3.4.4 Pre Coat Report * (ASTM D 276) 3.4.5 Secondary Foundation Report * (ASTM D 276) 3.4.6 Secondary Backing Report * (ASTM D 276) * Materials approved for each suppliers construction can be found in the FMD (Ford Ma

9、terial Database). 3.5 CONSTRUCTION 3.5.1 Pile Yarn 1320 Denier (ASTM D 1244) 3.5.2 Pile Count (ISO 1763) Rows / 100 mm 31.5 Stitches / 100 mm 42.5 Rows and stitches per 100 mm shall be based on an average count on a 254 mm length of carpet and shall not exceed the tolerance provided on the approved

10、construction supplement in the FMD for the approved material. 3.5.3 Needle Gauge 3.18 mm 3.5.4 Filament Count 68 filaments per bundle 3.5.5 Ply Twist 2 3.6 THICKNESS 3.6.1 Pile (Loop) Height 4.75 mm Nominal (ISO 1765) Pile Height tolerances approved for each suppliers construction can be found in th

11、e FMD (Ford Material Database). 3.6.2 Primary Foundation 0.5 +/- 0.1 mm (ISO 1765) 3.6.3 Back Coating (mm) Report * (ISO 1765) The back coating shall thoroughly saturate the base of the pile fiber bundles to ensure adequate tuft lock. Penetration of the back coating through to the face shall be cont

12、rolled to provide the required resistance to abrasion and fiber loss, but it shall not be visible on the face of the pile fiber. ENGINEERING MATERIAL SPECIFICATION WSS-M3H150-A Copyright 2015, Ford Global Technologies, LLC Page 3 of 4 3.6.4 Pre Coat (mm) Report * (ISO 1765) 3.6.5 Secondary Foundatio

13、n (mm) Report * (ISO 1765) 3.6.6 Secondary Backing (mm) Report * (ISO 1765) * Thicknesses and tolerances approved for each suppliers construction can be found in the FMD (Ford Material Database). 3.7 WEIGHT 3.7.1 Pile Yarn 713 g/m2 (21 oz) (ASTM D5848) Nominal 3.7.2 Primary Foundation 110 g/m2 (10 o

14、z) (ASTM D5848) Nominal 3.7.3 Back Coating (g/m2 (oz) Report * (ASTM D5848) 3.7.4 Pre Coat (g/m2 (oz) Report * (ASTM D5848) 3.7.5 Secondary Foundation (g/m2 (oz) Report * (ASTM D5848) 3.7.6 Secondary Backing (g/m2 (oz) Report * (ASTM D5848) * Weights and tolerances approved for each suppliers constr

15、uction can be found in the FMD (Ford Material Database). 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRAWING CALL OUT The

16、 following shall be called out on the Engineering drawing to correctly designate the approved material. WSS-M3H150-A Supplier Name and Product Code WSS-M15P44-B 5. SUMMARY OF REVISIONS 2015 05 08 Added limitation not allowing compression molded mats for 2016 and beyond. ENGINEERING MATERIAL SPECIFIC

17、ATION WSS-M3H150-A Copyright 2015, Ford Global Technologies, LLC Page 4 of 4 Floor Mat Construction Supplement Supplier _Supplier Contact Name_ Number _ Product Name _ Supplier Rubber Grade _ Supplier Product Code _ Performance Specification _ Supplier Lab Number _ Supplier Lab Date _ Manufacturing

18、Location _ Composition Product Code / Trade Name Supplier Pile Yarn ASTM D276 _ _ Primary Foundation ASTM D276 _ _ Back Coating (rubber) ASTM D276 _ _ Pre Coat ASTM D276 _ _ Secondary Foundation ASTM D276 _ _ Secondary Backing ASTM D276 _ _ Construction Solution or piece dyed (circle one) Please pro

19、vide the following thermal data on the rubber backing: FTIR (ASTM E1252) _ DSC (ASTM D1356/D3418) _ TGA (ASTM E1131) _ Pile Yarn ASTM D1244 _ Denier Pile Count ISO 1763 _+/- _ binding sites/ 100 mm length _+/- _binding sites/100 mm width Needle Gauge _ mm Pile Thickness ISO 1765 _+/- _ mm Primary Th

20、ickness ISO 1765 _+/- _ mm Back Coating Thickness ISO 1765 _+/- _ mm Pre Coat Thickness ISO 1765 _+/- _ mm Secondary Thickness ISO 1765 _+/- _ mm Secondary Backing Thickness ISO 1765 _+/- _ mm Mass per Unit Area Weight Pile Yarn ASTM D5848 _+/- _ g/m2 Primary Foundation ASTM D5848 _+/- _ g/m2 Back Coating (rubber) ASTM D5848 _+/- _ g/m2 Pre Coat ASTM D5848 _+/- _ g/m2 Secondary Foundation ASTM D5848 _+/- _ g/m2 Secondary Backing ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Design Verification _ Production Verification _