FORD WSS-M3H151-B1-2016 CARPET BCF NYLON 6 CUT PILE PRINCETON PATTERN 390 g m2 (11 5 oz) POLYESTER BACKING TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2016 05 30 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 5 CARPET, BCF NYLON 6, CUT PILE, WSS-M3H151-B1 PRINCETON PATTERN, 390 g/m2 (11.5 oz), POLYESTER BACKING CARPET,

2、 BCF NYLON 6, CUT PILE, WSS-M3H151-B2 PRINCETON PATTERN, 390 g/m2 (11.5 oz), MASS BACKING 1. SCOPE The materials defined by this specification are bulked continuous filament (BCF) nylon, cut pile carpets, tufted into a synthetic primary foundation. 2. APPLICATION This material was originally release

3、d for F150 and Lincoln floors. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of appr

4、oved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity.

5、 Testing of the material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1

6、/ latest. Test data must to be provided by the Tier 1 at the appropriate program milestone. 3.3.2 In addition to the requirements listed herein, the end-item mat assembly shall be tested to WSS-M8P16-B and any additional SDS requirements. The details for each of the suppliers specific construction s

7、hall be documented in the supplement attached and uploaded into the or scanned data package 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods prior to any subsequent operations, such as reheating or molding. 3.5 APPEARANCE ENGINEERING MATERIAL S

8、PECIFICATION WSS-M3H151-B1/B2 Copyright 2016, Ford Global Technologies, LLC Page 2 of 5 The color, pattern, and gloss shall match the approved Corporate Design Center master sample. 3.6 COMPOSITION 3.6.1 Pile Yarn Nylon 6 (ASTM D 276) 3.6.2 Primary Foundation 100% Polyester (ASTM D 276) 3.6.3 Back C

9、oating Polyethylene (ASTM D 276) 3.6.4 Secondary Backing (ASTM D 276) 3.6.4.1 B1 Only Polyester 3.6.4.2 B2 Only Elastomer 3.7 METHOD OF DYING Piece 3.8 CONSTRUCTION 3.8.1 Pile Yarn 1400 Denier (ASTM D 1244) 3.8.2 Pile Count (ISO 1763) Rows / 100 mm 39.4 Stitches / 100 mm 40.0 Rows and stitches per 1

10、00 mm shall be based on an average count on a 254 mm length of carpet and shall not exceed the tolerance provided on the approved construction supplement for the approved material. 3.8.3 Needle Gauge 2.54 mm 3.9 THICKNESS 3.9.1 Pile Height 5.5 mm Nominal (ISO 1765) Pile Height tolerances approved fo

11、r each suppliers construction can be found in the construction package 3.9.2 Primary Foundation 0.57 +/- 0.11 mm (ISO 1765) 3.9.3 Back Coating 0.03 +/- 0.001 mm (ISO 1765) The back coating shall thoroughly saturate the base of the pile fiber bundles to ensure adequate tuft lock. Penetration of the b

12、ack coating through to the face shall be controlled to provide the required resistance to abrasion and fiber loss, but it shall not be visible on the face of the pile fiber. ENGINEERING MATERIAL SPECIFICATION WSS-M3H151-B1/B2 Copyright 2016, Ford Global Technologies, LLC Page 3 of 5 3.9.4 Secondary

13、Backing (mm) Report * (ISO 1765) *Thicknesses and tolerances approved for each suppliers construction can be found on the supplement form in the construction package. 3.10 WEIGHT 3.10.1 Pile Yarn 389 g/m2 (11.5 oz) (ASTM D5848) Nominal 3.10.2 Primary Foundation 110 g/m2 (3.2 oz) (ASTM D5848) Nominal

14、 3.10.3 Back Coating (g/m2 (oz) Report * (ASTM D5848) 3.10.4 Secondary Backing (B1 Only) (g/m2 (oz) Report* (ASTM D5848) 3.10.5 Secondary Mass Backing (B2 Only) (g/m2 (oz) Report * (ASTM D5848) * Weights and tolerances approved for each suppliers construction can be found in the supplement form on t

15、he construction package. 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRAWING CALL OUT The following shall be called out o

16、n the Engineering drawing to correctly designate the approved material. WSS-M3H151-B1 Or WSS-M3H151-B2 Supplier Name and Product Code WSS-M8P16-B 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product D

17、evelopment, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples

18、 must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.3 SUPPLIERS ONGOING RESPONSIBILITY All materia

19、ls must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION WSS-M3H151-B1/B2 Copyright 2016, Ford Global Technologies, LLC Page 4 of 5 Prior to making any changes to the material originally approved, whether or not such

20、changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineer

21、ing Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.4 RESTRICTED SUBSTANCE MAN

22、AGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comp

23、ly with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WSS-M3H151-B1/B2 Copyright 2016, Ford Global Technologies, LLC Page 5 of 5 Floor Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product

24、 Name _ Supplier Substrate Grade _ Supplier Product Code _ Performance Specification _ Supplier Lab Number _ Supplier Lab Date _ Manufacturing Location _ Composition Type Supplier Pile Yarn ASTM D276 _ _ Primary Foundation ASTM D276 _ _ Back Coating ASTM D276 _ _ Pre Coat ASTM D276 _ _ Secondary Bac

25、king ASTM D276 _ _ Construction Solution or piece dyed (circle one) Recycled % (PIR/PCR) _ Denier _ Filament Count _ Pile Yarn ASTM D1244 _ Pile Count ASTM D5793 _+/- _ binding sites/ 100 mm length _+/- _binding sites/100 mm width Needle Gauge _ mm Pile Thickness ASTM D6859 _+/- _ mm Primary Thickne

26、ss ASTM D6859 _+/- _ mm Back Coating Thickness ASTM D6859 _+/- _ mm Pre Coat Thickness ASTM D6859 _+/- _ mm Secondary Thickness ASTM D6859 _+/- _ mm Mass per Unit Area Weight Pile Yarn ASTM D5848 _+/- _ g/m2 Primary Foundation ASTM D5848 _+/- _ g/m2 Back Coating ASTM D5848 _+/- _ g/m2 Pre Coat ASTM D5848 _+/- _ g/m2 Secondary Backing ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Design Verification _ Production Verification _