FORD WSS-M4C113-C-2014 FUEL GASOHOL UNLEADED INITIAL FILL BRAZIL TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2014 07 02 Released L. Benvenutti, SA Controlled document at www.MATS Copyright 2014, Ford Global Technologies, LLC Page 1 of 5 FUEL, GASOHOL, UNLEADED, INITIAL FILL, BRAZIL WSS-M4C113-C 1. SCOPE The material defined by this specificat

2、ion is a well-refined unleaded gasoline containing ethanol according to market fuel regulations and normal commercial additives. 2. APPLICATION This specification was released originally for material used as initial fill fuel for vehicles designed to operate on gasoline in Brazil. Additives are pres

3、ent to protect the fuel system. This material is not specifically intended for use in certification testing. It may be used for engine hot test, mileage accumulation or general fueling. 3. REQUIREMENTS This material must be produced using current refinery practices for market place fuels and must me

4、et all pertinent legal gasoline requirements in the country in use. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 ADDITIVES Fuels shall contain normal commerci

5、al additives at concentrations representative of good commercial practice in the receiving locale (unless otherwise specified). Metallic additives, including lead, manganese, iron and phosphorus, are not allowed. 3.3 ODOR The material shall have the usual characteristic odor of gasohol. There shall

6、be no obvious foreign odors. 3.4 COLOR (Visual) Color can vary from colorless to yellow when no dye is used. The use of dye is permitted at a maximum concentration of 50 ppm, except blue, restricted for aviation. 3.5 APPEARANCE (ABNT NBR 14954 or ASTM D4176) Clean and free of impurities ENGINEERING

7、MATERIAL SPECIFICATION WSS-M4C113-C Copyright 2014, Ford Global Technologies, LLC Page 2 of 5 3.6 OCTANE NUMBERS 3.6.1 Motor 82.0 min (ISO 5163 / ASTM D2700) 3.6.2 Research Report (ISO 5164 / ASTM D2699) 3.6.3 AKI (Anti Knock Index) 87.0 min (ASTM D2699 / D2700) 3.7 TOTAL SULFUR 50 mg/kg max (ASTM D

8、2622 / D3120 / D5453 / D6920 / D7039 / D7220) 3.8 METAL CONTENT 3.8.1 Lead 5.0 mg/L max (ASTM D3237) 3.8.2 Phosphorus 1.3 mg/L max (ASTM D3231) 3.9 COMPOSITION 3.9.1 Hydrocarbons (ABNT NBR 14932 / ASTM D1319) % volume Aromatics 35 max Olefins 25 max Saturates Report 3.9.2 Benzene 1.0 %vol max (ABNT

9、NBR 15289 / 15441 / ASTM D3606 / D5443 / D6277) 3.9.3 Gum Content (NBR 14525 / ASTM D381) Washed 5 mg/100 mL max Unwashed Report 3.9.4 Ethanol Content (anhydrous) Must follow valid (ABNT NBR 13992 / ASTM D5501) national market fuel regulation 3.10 DISTILLATION RANGE (ABNT NBR 9619 / ASTM D86) Volume

10、 Evaporated Temperature Initial boiling point Report 10% 65C max 50% 80C max 90% 190C max Final boiling point 215C max Residue, 2% volume max ENGINEERING MATERIAL SPECIFICATION WSS-M4C113-C Copyright 2014, Ford Global Technologies, LLC Page 3 of 5 3.11 VAPOR PRESSURE (ABNT NBR 14149 / 14156 / ASTM D

11、4953 / D5191) 3.11.1 Seasonal Geographical Volatility Shall meet the local appropriate specifications. 3.12 OXIDATION STABILITY 360 minutes min (NBR 14478 / ASTM D525) 3.13 CORROSION PROTECTION 3.13.1 Copper Corrosion 1 max (NBR 14359 / ASTM D130; 3 h at 50 C) 3.13.3 Ferrous Corrosion Pass (ASTM D66

12、5, Procedure A at 4 hours) 3.14 DEPOSIT CONTROL 3.14.1 Intake Valve Deposits (ABNT NBR 16038) 100 mg/valve max or (ASTM D6201) 50 mg/valve max or (ASTM D5500) 100 mg/valve max 3.15 CERTIFICATION Supplier shall certify that the gasoline is a formula that has been tested and meets Ford Motor Company r

13、equirements as stated in these specifications. Technical evidence of these data and manufacturing limits must be tabulated on the attached form. This certification shall be signed by the suppliers director of research or other authorized official and submitted to the responsible Ford purchasing acti

14、vity. This information will then be forwarded to the Materials Activity of the Engine Product Engineering Office or to the product engineering office responsible for source approval. 3.16 SPECIFIC GRAVITY at 20C Report (ABNT NBR 7148 / 14065 / ASTM D1298 / D4052) 4. GENERAL INFORMATION The informati

15、on given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing Engineering Department or other r

16、esponsible activity shall notify both the Security and Safety Units of its presence to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notifications. ENGINEERING MATERIAL SPECIFICATION WSS-M4C113-C Copyright 2014, Ford Global Tech

17、nologies, LLC Page 4 of 5 4.2 WATER CONTAMINATION It is important that this material is not contaminated with water as this will cause separation of the ethanol from the gasoline base rendering the material unfit for use. Storage facilities should be regularly bottom sampled to check for any separat

18、ion. 4.3 SAMPLING AND SUBMISSION OF SAMPLES (ISO 3170 / 3171, ASTM D4057 / D4177) Quality control records must be made available to Fuels and Lubricants Engineering upon request. ENGINEERING MATERIAL SPECIFICATION WSS-M4C113-C Copyright 2014, Ford Global Technologies, LLC Page 5 of 5 Company _ Termi

19、nal _ Volatility Grade _ Specification _ Date _ Inspection Results Specification Typical Manufacturing Limits Appearance Clean and free of Impurities _ _ Motor Octane Number 82.0 min _ _ Anti Knock Index 87.0 min _ _ Research Octane Number Report _ _ Metals, mg/L Pb 5.0 max _ _ P 1.3 max _ _ Total S

20、ulfur, mg/kg 50 max _ _ Copper Corrosion, 3h50C 1b max _ _ Ferrous Corrosion Rating B+ min B+ min _ _ Oxidation Stability.100C 360 min _ _ Vapor Pressure, kPa Report _ _ Specific gravity at 20C Report _ _ Distillation Range Initial Boiling Point, C Report _ _ 10% Evaporated, C 65C max _ _ 50% Evapor

21、ated, C 80 C max _ _ 90% Evaporated, C 190C max _ _ Final Boiling Point, C 215 C max _ _ Residue, % vol 2 max _ _ Hydrocarbons, % vol Aromatics 35 max _ _ Olefins 25 max _ _ Saturates Report _ _ Benzene, % vol 1.0 max _ _ Gum, mg/100 ml washed 5 _ _ Gum, mg/100 ml unwashed Report _ _ Ethanol Content (E99), % vol Report _ _ Deposit Control (IVD), mg/valve ABNT NBR 16038 100 max _ _ ASTM D6201 50 max _ _ ASTM D5500 100 max _ _ Additives Type & Formula Manufacturing Limits Anti-oxidant _ _ Anti-corrosion _ _ Detergent _ _ Dispersant _ _ Metal Deactivator _ _ Miscellaneous _ _ Signature_ Title_