ImageVerifierCode 换一换
格式:PDF , 页数:9 ,大小:68.90KB ,
资源ID:753436      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-753436.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD WSS-M4D1005-A1-2016 THERMOPLASTIC POLYOLEFIN ELASTOMER (TPO) HIGH MELT FLOW 22% MINERAL FILLED MOLD-IN-COLOR ONLY MOLDING COMPOUND FASCIA THIN-WALLED EXTERIOR TO BE USED WIT.pdf)为本站会员(towelfact221)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD WSS-M4D1005-A1-2016 THERMOPLASTIC POLYOLEFIN ELASTOMER (TPO) HIGH MELT FLOW 22% MINERAL FILLED MOLD-IN-COLOR ONLY MOLDING COMPOUND FASCIA THIN-WALLED EXTERIOR TO BE USED WIT.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 3 2016 08 31 Revised See Summary of Revisions G. Kirsankina, EU 2015 02 16 Editorial See Summary of Revisions K. Mueller, NA 2008 11 20 Activated K.Mueller, FNA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LL

2、C Page 1 of 9 THERMOPLASTIC POLYOLEFIN ELASTOMER (TPO), WSS-M4D1005-A1 HIGH MELT FLOW, 22% MINERAL FILLED, MOLD-IN-COLOR ONLY, MOLDING COMPOUND, FASCIA / THIN-WALLED EXTERIOR THERMOPLASTIC POLYOLEFIN ELASTOMER (TPO), WSS-M4D1005-A2 HIGH MELT FLOW, 22% MINERAL FILLED, FULLY PAINTED ONLY, MOLDING COMP

3、OUND, FASCIA / THIN-WALLED EXTERIOR 1. SCOPE The material defined by these specifications are 22% mineral filled thermoplastic molding compounds for mold-in-color (A1) and painted (A2) applications, based on thermoplastic polyolefin elastomer. 2. APPLICATION WSS-M4D1005-A1 This specification was rel

4、eased originally for material used for mold-in-color exterior bumper applications (where the fascia thickness is less than 3mm), requiring high melt flow rate. Any color additives need to be reviewed and approved by the raw material supplier and Ford Materials Engineering. The UV/process/heat stabil

5、izers must be in the base resin from the material supplier, not in the color concentrate, specifically for mold-in-color applications at the press. WSS-M4D1005-A2 This specification was released originally for material used for painted exterior bumper applications (where the fascia thickness is less

6、 than 3mm), requiring high melt flow rate. Any color additives need to be reviewed and approved by the raw material supplier and Ford Materials Engineering. The process/heat stabilizers must be in the base resin from the material supplier. 2.1 LIMITATIONS Material approved to WSS-M4D1005-A1 is likel

7、y to contain additives that may negatively affect paint adhesion, therefore should not be used for painted applications. Material approved to WSS-M4D1005-A2 is unlikely to contain UV stabilizers, therefore long term exposure to direct sunlight could cause chalking and loss of gloss. 3. REQUIREMENTS

8、3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). Note: Many 4D resin specifications prior to 2011, identified certain requirements with the symbol (s), which indicate

9、d that the mean and +/- 3 sigma values were to be reported. The specification minimum, maximum or range was established using 3 sigma data. For 2011 and beyond, refer to Table 1 for number of samples required for each test to establish specification limits. ENGINEERING MATERIAL SPECIFICATION WSS-M4D

10、1005-A1 WSS-M4D1005-A2 Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 2 of 9 This specification is based on virgin materials, however materials with recycled content as defined by WRS-M99P42-A1 (post-consumer and/or post industrial recyclates and repolymerised rec

11、ycled materials) should be used whenever technically feasible and following all materials and PV testing required by Ford Materials Engineering. The use of regrind is permitted, for economic / environmental reasons, with compliance as indicated in WSS-M99P1111-A. 3.1.1 Performance Criteria: Exterior

12、 mold-in-color substrates approved to WSS-M4D1005-A1 must comply with all the requirements of WSS-M98P13-C/Latest. Painted substrates approved to WSS-M4D1005-A2 must comply with all the requirements of paint performance WSS-M2P181-C/Latest. Parts must fulfill applicable SDS/CDS requirements. 3.1.3 T

13、he material supplier must retain 30-50 lbs. (14-23 kg) of pelletized material / lot produced for 6 months (WSS-M4D1005-A2 only). 3.1.4 Unless otherwise agreed to by Ford Materials Engineering, Control Plan and Certificate of Analysis (CoA) lot testing requirements must include, but are not limited t

14、o: Melt Flow Rate Mineral Filler Content Impact Strength, Notched Izod at 23C Flexural Modulus Molding Shrinkage (WSS-M4D1005-A1 / A2) Post Shrinkage (WSS-M4D1005-A2) 3.2 SAMPLE PREPARATION Unless otherwise specified all tests shall be carried out on injection molded, one-end gated test specimens. T

15、he test specimens A and D shall be molded using molding conditions defined in ISO 1873-2. No annealing is allowed. See Tables 1 and 2 for the number of samples required. Specimens shall be as follows: Specimen A 150 minimum x 10 x 4.0 +/- 0.2 mm (ISO 527-2, Specimen Type 1A) Specimen B 355 x 100 x 1

16、.0 +/- 0.1 mm (ISO 3795) Specimen C 145 x 60 x 3.2 +/- 0.2 mm Specimen D Center of Specimen A, 80 x 10 x 4.0 +/- 0.2 mm Specimen E 100 mm diameter x 3.2 mm Specimen F 80 mm diameter x 3.2 mm Specimen G 90 mm x 200 mm Specimen H 50 +/- 1 mm diameter x 3.2 +/- 0.2 mm Specimen I 100 mm x 150 mm, min 3.

17、3 APPEARANCE (WSS-M41005-A1 only) 3.3.1 Weathering Resistance Rating 4 min (SAE J2527 Atlas Water Cooled, Rotary Drum Xenon-Arc Apparatus only. Modified Type “S“ borosilicate inner and outer filters, 0.55 W/m2 radiant exposure monitored at 340 nm, 3000 h total exposure or as otherwise defined, Speci

18、men C, from smooth polished mold, ISO 105-A02 / AATCC Evaluation Procedure 1) For color durability submissions, test all program colors ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 3 of 9 3.3.2 1 a

19、nd 2 year Florida Rating 4 min Initial Qualification for new resin technology (SAE J1976, 5 south, direct weathering inland, Specimen C from smooth polished mold, ISO 105-A02 / AATCC Evaluation Procedure 1) After exposure the material shall show no color change in excess of the specified AATCC Ratin

20、g. In addition, there shall be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be achieved as specified below by washing with mild detergents and water (ratio 5:95 by volume) or equivalent after the outdoor exposur

21、e only. All initial approvals may be based on the accelerated weathering exposure, pending real world outdoor exposure results for final approval. 3.3.3 Resistance to Scratch and Mar (FLTM BO 162-01, Specimen I) Scratch Rating 2 at 2 N, max Whitening/Color Change Rating 1 at 7 N, max Marring Rating

22、2 at 2 N, max These values are derived from colored and grained samples in agreement with Materials Engineering. Details regarding color house, let down ratio, colors, grain, etc can be found in the approval package. 3.4 MATERIAL PROPERTIES 3.4.1 Melt Flow Rate 26 - 46 g/10 minutes (ISO 1133, 230 C,

23、 2.16 kg) 3.4.2 Filler Content 21 23.5% (ISO 3451-1, Method A, talc filler, (online process control) 3 h at 650 +/- 25 C, test portion 1 -2 g) 3.4.3 Density 1.04 1.08 g/cm3 (ISO 1183, Method A) 3.4.4 Hardness, Durometer D 56 - 67 (ISO 868, 15 s dwell) 3.4.5 Tensile Strength at Yield 17 MPa, min (ISO

24、 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A, test speed: 50 mm/minute) 3.4.6 Tensile Modulus 1994 MPa, min (ISO 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A test speed: 5 mm/min) ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled docum

25、ent at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 4 of 9 3.4.7 Impact Strength, Notched Izod (ISO 180/1A, Specimen D) 3.4.7.1 At 23 +/- 2 C 28 kJ/m2, min Partial Break 3.4.7.2 At - 40 +/- 2 C 2.6 kJ/m2, min Complete Break 3.4.7.3 At 0 +/- 2 C 8.0 kJ/m2, min Partial and Complete Brea

26、k The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold chamber, if not possible, test may be conducted outside, but within 5 seconds. 3.4.8 Flexural Modulus 1900 2400 MPa (ISO 178,

27、Specimen D, 64 mm support span, 2 mm/minute test speed) 3.4.9 Heat Deflection Temperature 47 C, min (ISO 75-1 & ISO 75-2, Specimen D, flatwise, 0.34 +/- 0.1 mm deflection. At 1.80 MPa) 3.4.10 Heat Aging Performance (ISO 188, 150 +/- 50 air changes/h, 1000 h at 120 +/- 2 C. Unaged property values sha

28、ll be determined at the time of the aged properties determination) 3.4.10.1 Tensile Strength at Yield Change +/- 10% max (Test Method per para 3.4.5) 3.4.10.2 Impact Strength, Notched Izod Change +/- 20% max (Test Method per para 3.4.7.1, specimens to be notched before heat aging) 3.4.11 Coefficient

29、 of Linear Thermal Expansion (ISO 11359-2, -30C to 100C) Flow Direction 4.4 - 6.5 E-5 mm/mm/ C X-Flow Direction 5.0 - 7.4 E-5 mm/mm/ C (For Reference only: ASTM E228, -30 C - 100 C) Flow Direction 2.7 - 4.5 E-5 mm/mm/ C X-Flow Direction 3.5 - 4.4 E-5 mm/mm/ C 3.4.12 Flammability (ISO 3795/SAE J369 S

30、pecimen B smooth surface) Burn Rate 100 mm/minute 3.4.13 Mold Shrinkage (ISO 294-3 and 294-4/ISO 2577, (specimen size is approx. 100 x 150 x 3.2 mm) 3.4.13.1 Molding Shrinkage . After 48 h at 23 +/- 2 C 0.55 0.75% ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled document a

31、t www.MATS Copyright 2016, Ford Global Technologies, LLC Page 5 of 9 3.4.13.2 Post Shrinkage (Separate specimens required for each test). Report total shrinkage. . After 30 minutes at 80 C 0.75 0.85% . After 30 minutes at 120 C 0.7 - 1.0% NOTE: For Part Shrinkage, please follow Design Rule EF011900-

32、1201. 3.5 PAINTABILITY 3.5.1 Painted substrate must comply with the requirements of WSS-M2P181-C/Latest, Table 1, Change In Approved Paint System, Primer or Substrate (plaques are acceptable). Submission data is not to be used as surrogate for final part performance testing. Paint system documented.

33、 3.6 MATERIAL PROPERTIES REPORT ONLY Values are retained in Ford Materials Database . 3.6.1 SLIDO (Friction Induced Wear) (FLTM BI 167-01, color = white only. Paint system consistent with 3.5.1.) 3.6.2 Impact Strength Multiaxial (ASTM D 3763, Impact velocity: 2.2 m/s Specimen E, smooth surface injec

34、tion molded specimen) Test specimens must be conditioned for minimum of 6 h at test temperature prior to impact testing. Low temperature conditioning and testing shall be conducted within the same environmental chamber as the clamp mechanism of the impact device. Painted test specimens must be orien

35、ted with paint in tension (paint side down). Summarize testing at each condition by providing the following information as well as the information in Figure 1. a. Detailed description of specimen preparation b. Molding conditions: melt and mold surface temperatures, and average injection velocity c.

36、 Number of samples tested per lot per temperature d. Numbers of lots tested e. Number of samples with ductile failure per each test condition f. Representative force vs. deflection curve for each impact event Test results shall be submitted with an initial qualification of the material with curves (

37、data on CD as well as paper copies) and test samples. A ductile failure is defined as a crack that does not radiate more than 10 mm from the center of the impact point. Report test data for 23 +/- 2 C, and the lowest of the following temperatures in which a minimum of 24 out of 30 ductile failures w

38、ere observed. Test specimens must be conditioned for minimum of 6 h at test temperature prior to impact testing. Low temperature testing shall be conducted within the same environmental chamber as the clamp mechanism of the impact device. Specimens can be transported from the conditioning environmen

39、t to the testing environment, provided the transfer is within 5 seconds. ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 6 of 9 3.6.2.1 Painted Specimens (WSS-M4D1005-A2) (Painted samples: Paint syste

40、m consistent with 3.5.1. Color = white only). 3.6.2.1.1 Energy at Maximum Load (At 23 2C) Report J Energy Absorbed % Ductile, min 100% 3.6.2.1.2 Energy at Maximum Load (At 15 2C) Report J Energy Absorbed % Ductile, min 80% 3.6.2.2 Unpainted Specimens (WSS-M4D1005-A1 and WSS-M4D1005-A2 should be test

41、ed unpainted) 3.6.2.2.1 Energy at Maximum Load (At -5 2 C) Report J Energy Absorbed % Ductile, min 100% 3.6.2.2.2 Energy at Maximum Load (At -10 2 C) Report J Energy Absorbed % Ductile, min 80% Operator NameSample IDTest no Date/time Lot ID Temperature ( C )Impact velocity (m/s)Impact energy (J)Time

42、 to max load (ms)Total time (ms)Maximum load (kN)Energy to max load (J)Total energy (J)Deflection at max load (mm)# of CracksCrack length, max. (mm)Failure type (Ductile / Brittle) 12345678910AverageMedianMinimumMaximumCoef. of Var.Std. Dev.Figure 1 - Data Summary 3.6.3 Optical Microscopy Test speci

43、men preparation includes immersion oil mount, with the thickness of the test specimen being 5 um thick. Test specimen shall be evaluated parallel to flow, taken half-way between the gate and edge of plaque. Magnifications shall be at both 200x and 600x. Photographs required at 200x and 600x magnific

44、ations. ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 7 of 9 3.6.4 Impact Strength, Notched Charpy (ISO 179-1/2, Specimen D) 3.6.4.1 At 23 +/- 2 C Report Value, kJ/m2 Report Break Type 3.6.4.2 At -4

45、0 +/- 2 C Report Value, kJ/m2 Report Break Type 3.6.4.3 At 0 +/- 2 C Report Value, kJ/m2 Report Break Type The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold chamber, if not possi

46、ble, test may be conducted outside, but within 5 seconds. 3.6.5 Poissons Ratio Report Ratio (ISO 527-1/2, Specimen A, 1 mm/minute test speed) 3.6.6 Additional FMD Required Information FTIR/TGA/DSC/CLTE Curves 4. GENERAL INFORMATION The information given below is provided for clarification and assist

47、ance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications 4.1 TYPICAL PROPERTIES USING METHODS IN SECTION 3.6 Test Typical Value Units 3.6.1 SLIDO (Friction Induced Wear) 1100 - 1500 / 4893 - 6672 lbf / N 3.6.2.1 Impact Strength Mul

48、tiaxial, Painted Specimens, Energy at Maximum Load At 23 C At 15 C 15 12 J J 3.6.2.2 Impact Strength Multiaxial, Unpainted Specimens, Energy at Maximum Load At -5 C At -10 C 25 20 J J 3.6.4 Impact Strength, Notched Charpy At 23C At -40C At 0C 44 2.7 11 kJ/m2 kJ/m2 kJ/m2 3.6.5 Poisson Ratio 0.43 n/a

49、ENGINEERING MATERIAL SPECIFICATION WSS-M4D1005-A1 WSS-M4D1005-A2 Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 8 of 9 4.2 MATERIAL IDENTIFICATION FOR TPO-(PP+EPDM)-MD22 RECYCLING PURPOSES (ISO 1043, ISO 11469, ISO 18064) Table 1: Minimum Sample Size Initial Approva

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1