FORD WSS-M4D492-B1-2010 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 15% MINERAL COLOR PIGMENTED UV STABILIZED HIGH MELT FLOW HIGH MODULUS MOLD IN COLOR AND PARTIALLY PAINTED EXTERIOR .pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 11 11 N-STATUS Go to N status so allow deviation can be issued to Gran Siam X360T material on MFR, HDT A. Pan, APA 2006 11 09 Activated K. Mueller Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 6 T

2、HERMOPLASTIC POLYOLEFIN ELASTOMER (TEO), 15% MINERAL, COLOR WSS-M4D492-B1 PIGMENTED, UV STABILIZED, HIGH MELT FLOW, HIGH MODULUS, MOLD IN COLOR AND PARTIALLY PAINTED, EXTERIOR NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a filled, weatherable and paintable the

3、rmoplastic molding compound. 2. APPLICATION This specification was released originally for material used for exterior ornamentation applications that are mold-in-color and partially painted (i.e.: bodyside moldings, claddings, rocker panels, wheel lips). Any color additives need to be reviewed and a

4、pproved by the raw material supplier and Ford Materials Engineering. The UV/heat stabilizers must be in the base resin from the material supplier, not in the color concentrate, for mold-in-color applications at the press. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material su

5、ppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1.1 All requirements of this specification, identified by symbol (s), shall be met with data representing 3 sigma values using latest ISO test methods. 3.1.2 This specification

6、was developed using virgin material properties. The use of regrind is permitted, for economic / environmental reasons, with compliance as indicated in WSS-M99P1111-A. 3.1.3 Critical Process Parameters At the request of Ford Materials Engineering the supplier shall be responsible to collect critical

7、process control data on each lot of material produced. Testing required will be jointly developed between Ford Materials Engineering and the supplier based on CP and PFMEA review at the time of initial approval. Annually the supplier will review the in process data with Ford Materials Engineering to

8、 show that the process has remained under control. The data needs to be submitted in January for the previous calendar year. Data showing poor quality control measures or lack of submitted data may result in deletion from the Ford Approved Source List. 3.2 MOLDING COMPOUND (s) 3.2.1 Melt Flow Rate 2

9、2 - 34 g/10 minutes (ISO 1133, 230C, 2.16 kg) (s) 3.2.2 Mineral Filler Content 12 - 18% (ISO 3451-1, Method A, talc filler, 3 h at 650 +/- 25 C, test portion 1 - 2 g) ENGINEERING MATERIAL SPECIFICATIONWSS-M4D492-B1 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2

10、of 6 3.3 MOLDED TEST SPECIMEN 3.3.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following dimensions are required: A. 150 minimum x 10 x 4.0 +/- 0.2 mm (ISO 3167, Type 1A) B. 60 x 60 x 2.0 +/- 0.1 mm (I

11、SO/DIS 294-3) C. 355 x 100 x 1.0 +/- 0.1 mm (ISO 3795) Test specimen A shall be molded using molding conditions defined in ISO 1873-2. Specimens with shorter dimensions shall be cut from the center of the specimen A. No annealing allowed. 3.3.2 Density 0.99 1.03 g/cm3(ISO 1183, Method A) 3.3.3 Hardn

12、ess, Durometer D 57 (ISO 868, 15 s dwell) (s) 3.3.4 Tensile Strength at Yield, min 15.5 MPa (ISO 527-1 150 x 10 x 4 mm specimen A). Test speed shall be 50 mm/minute for all materials. Provide a curve of tensile stress versus strain using one specimen per lot at each of the following temperatures: -4

13、0 C, 23 C and 85 C. For ductile materials, the curve shall cover strain through yield point. (s) 3.3.6 Impact Strength, Izod, notched, min (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, 10 specimens for each test) 3.3.6.1 At 23 +/- 2 C 9.3 kJ/m2 Minimum (not -3 sigm

14、a value) 18.0 kJ/m23.3.6.2 At -40 +/- 2 C 1.5 kJ/m23.3.6.3 At 0 +/- 2 C 3.7 kJ/m2The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold chamber, if not possible, test may be conducted

15、 outside, but within 5 seconds. ENGINEERING MATERIAL SPECIFICATIONWSS-M4D492-B1 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 6 (s) 3.3.7 Flexural Modulus, min 1250 MPa (ISO 178, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, 2 mm/min te

16、st speed, 64 mm support span) The test specimen must be conditioned for minimum of 6 hours at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold chamber, if not possible, test may be conducted outside, but within 5 seconds. 3.3.8 Heat Deflecti

17、on Temperature, min 52 C (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection. At 1.80 MPa) 3.3.9 Heat Aging Performance (ISO 188, except 150 +/- 50 air changes/h, 1000 h at 120 +/- 2 C. Unaged property values shall be determi

18、ned at the time of the aged properties determination) 3.3.9.1 Tensile Strength at Yield Change +/- 10% (Test Method per para 3.3.3) 3.3.9.2 Impact Strength, Izod Change +/- 15% (Test Method per para 3.5.5.1, specimens to be notched before heat aging) 3.4 SCRATCH RESISTANCE, MOLD-IN-COLOR ONLY (FLTM

19、BN 108-13, 1.0 +/- 0.1 mm steel ball at 7.0 N, 6.0 N, 4.5 N, 3.0 N and 2.0 N) Rating 2, max required at 2.0 N (No visible whitening at any load) 3.5 PAINTABILITY Painted substrate using this material must comply with all the requirements of paint performance WSS-M2P181-B. Production level materials

20、must be used in preparing test parts/panels. The use of improper sample prep materials can influence test results. 3.6 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm (use specimen C) with a smooth surface.

21、ENGINEERING MATERIAL SPECIFICATIONWSS-M4D492-B1 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 6 3.7 WEATHERING RESISTANCE, MOLD-IN-COLOR ONLY After exposure in accordance with 3.7.1 the material shall show no color change in excess of specified Gray Scale ra

22、ting (AATCC Evaluation Procedure 1/ISO 105-A02). In addition, there shall be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be achieved as specified below by washing with mild detergents and water (ratio 5:95 by v

23、olume) or equivalent after the outdoor exposure only. 3.7.1 Xenon Arc Weatherometer Rating 4 (SAE J1960 modified Type “S“ with at least borosilicate inner and outer filters, 75% gloss 0.55 W/m2radiant exposure retention 3000 h exposure, specimen size: 60 x 60 x 2.0 +/- 0.1 mm thick, smooth surface,

24、low gloss injection molded specimen B) Color submissions: all program colors 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 COEFFICIENT OF LINEAR THERMAL EXPANSION (ASTM D 696, -30C - 100 C) Flow

25、Direction 5.6-5mm/mm/C Cross-Flow Direction 5.6-5mm/mm/C (ISO 11359-2 TMA, -30C - 100 C) Flow Direction 6.6-5 mm/mm/C Cross-Flow Direction 7.1-5 mm/mm/C 4.2 MOLD SHRINKAGE (ISO 294-3 and 294-4, 60 x 60 x 2.0 +/- 0.1 mm injection molded specimen B) 4.2.1 Molding Shrinkage . After 48 h at 23 +/- 2 C (

26、flow direction) 0.7% . After 48 h at 23 +/- 2 C (cross-flow direction) 0.7% 4.2.2 Post Shrinkage (Separate specimens required for each test) . After 30 minutes at 120 C (flow direction) 1.0% . After 30 minutes at 120 C (cross-flow direction) 1.0% 4.3 CHARPY, NOTCHED (ISO 179/1eA, 80 x 10 x 4.0 +/- 0

27、.2 mm specimen use center section of specimen A, 10 specimens) 4.3.1 At 23 +/- 2 C 23 kJ/m24.3.2 At -40 +/- 2 C 3.5 kJ/m24.3.3 At 0 +/- 2 C 6.3 kJ/m2ENGINEERING MATERIAL SPECIFICATIONWSS-M4D492-B1 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 of 6 4.4 HEAT DEFL

28、ECTION TEMPERATURE 98 C (ISO 75-1 & ISO 75-2, 80 x 10 x 4.0 +/- 0.2 mm specimen use center section of specimen A, flatwise, 0.34 +/- 0.1 mm deflection. At 0.45 MPa) 4.5 IMPACT STRENGTH, MULTIAXIAL (ASTM D 3763, 100 mm diameter x 3.2 mm thick smooth surface injection molded specimen) Impact velocity:

29、 2.2 m/s for exterior/under the hood only applications 6.6 m/s for materials used in interior applications only 2.2 m/s and 6.6 m/s for materials used in both exterior/under-the-hood Report test data for 23 +/- 2 C, and the lowest of the following temperatures in which a minimum of 24 out of 30 duct

30、ile failures were observed: -40 +/- 2 C, or -30 +/- 2 C, or -15 +/- 2 C, or 0 +/-2 C, and 23 +/- 2 C. Test specimens must be conditioned for minimum of 6 h at test temperature prior to impact testing. Low temperature testing shall be conducted within the same environmental chamber as the clamp mecha

31、nism of the impact device. Specimens can be transported from the conditioning environment to the testing environment, provided the transfer is within 5 seconds. Test a minimum of 10 specimens from 3 individual lots at a single condition. Summarize testing at each condition by providing the following

32、 information as well as the information in Figure 1. a. Detailed description of specimen preparation b. Molding conditions: melt and mold surface temperatures, and average injection velocity c. Number of samples tested per lot per temperature d. Numbers of lots tested e. Number of samples with ducti

33、le failure per each test condition f. Representative force vs. deflection curve for each impact event Test results shall be submitted with an initial qualification of the material with curves (data on CD as well as paper copies) and test samples. A ductile failure is defined as a crack that does not

34、 radiate more than 10 mm from the center of the impact point. Operator NameSample IDTest no Date/time Lot ID Temperature ( C )Impact velocity (m/s)Impact energy (J)Time to max load (ms)Total time (ms)Maximum load (kN)Energy to max load (J)Total energy (J)Deflection at max load (mm)# of CracksCrack l

35、ength, max. (mm)Failure type (Ductile / Brittle) 12345678910AverageMedianMinimumMaximumCoef. of Var.Std. Dev.Figure 1 - Data SummaryENGINEERING MATERIAL SPECIFICATIONWSS-M4D492-B1 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 6 of 6 4.6 TENSILE MODULUS 1400 MPa (

36、ISO 527-1 & ISO 527-2, 150 minimum x 10 x 4.0 +/- 0.2 mm specimen A test speed: 1 mm/min) 4.7 MATERIAL IDENTIFICATION FOR RECYCLING PURPOSES (ISO 1043 latest) PP+EPDM-TD15 TENSILE STRESS VS TENSILE STRAIN ISO Tensile (50 mm/min Test Speed) End of graph does not indicate break except for -40 C. The property values shown are based on a limited number of tests and, therefore, should not be construed as product specifications.