FORD WSS-M5H40-A2-2015 LAMINATE POLYESTER FABRIC POLYURETHANE FOAM POLYESTER BACKING LYRIC PATTERN KNIT TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M5H40-A1).pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 3 2015 05 08 N Status Replaced by WSS-M5H40-B1/2 A. Wagenhaus, NA 2014 07 02 Editorial Clarified backing to be used in limitations D. Murtonen, NA 2014 04 03 Released D. Murtonen (FNA) Controlled document at www.MATS Copyright 2015, Ford

2、 Global Technologies, LLC Page 1 of 5 LAMINATE, POLYESTER FABRIC, POLYURETHANE FOAM, LYRIC PATTERN, KNIT WSS-M5H40-A1 LAMINATE, POLYESTER FABRIC, POLYURETHANE FOAM, POLYESTER BACKING, LYRIC PATTERN, KNIT WSS-M5H40-A2 NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification i

3、s a Lyric pattern, knit fabric, flame laminated to flame bondable polyether urethane foam or adhesive laminated to a backing scrim. 2. APPLICATION This specification was released originally for material used as cover material for headliners, sun visors, pillars and roller shades. Any other applicati

4、ons must be evaluated and approved by the responsible Materials Engineering activity. 2.1 LIMITATION Dark colors used for pillar applications, must use a dark colored backing to prevent read through. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS 3.1.1 Materials manufactured to t

5、his Specification shall also meet the requirements contained in WSS-M15P27- F/latest. 3.1.2 Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials WSS-M99P1111-A/latest. 3.1.3 Materials used in interior applications must meet the requirement

6、s outlined in WSS-M99P2222-D1/latest. 3.2 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 COMPOSITION 3.3.1 Fabric 100% Polyester (ASTM D276-12) 3.3.1.1 Weight (FLTM BN 106-01) Face fabric only 105 g/m2 +/- (5.5%) ENGINEERING MA

7、TERIAL SPECIFICATION WSS-M5H40-A1/A2 Copyright 2015, Ford Global Technologies, LLC Page 2 of 5 3.3.1.2 Fabric Count (ASTM D3887) Wales 130-161/10cm Courses 130-161/10cm 3.3.2 Foam Polyether Polyurethane The foam shall be polyether polyurethane and must meet Headlining Performance specification WSS-M

8、15P27-F. 3.3.2.1 Thickness As specified on Engineering Drawing 3.4 FABRIC-FOAM REQUIREMENTS See Table 1 for testing requirements. 3.4.1 Odor (FLTM BO 131-03-Variant C) Condition 1 = 23 +/- 2C Rating 3 min Condition 2 = 40 +/- 2C Rating 3 min Condition 3 = 65 +/- 2C Rating 3 min 3.4.2 Fogging (SAE J1

9、756, 3 hrs at 100C heating, 21C cooling plate, Posttest conditioning 16 hrs) Fog number 70 min Formation of a clear film, droplets or crystals is cause for rejection. 3.4.3 Flammability (ISO 3795/SAE J369) Burn Rate 100 mm/min. max Headliner fabric/foam composite shall be tested as 100% fully bonded

10、 to the headliner substrate as specified in WSS-M15P27-F/latest. Sun Visor fabric/foam composite must use appropriate foam to meet the 100mm/min. max as a fabric/foam composite if not 100% fully bonded to substrate. Pillar fabric/foam/scrim composite must use appropriate foam to meet the 100mm/min.

11、max as a composite if not 100% fully bonded to substrate. 3.4.4 Resistance to Abrasion 150 cycles (SAE J948, 500g load, CS-10 wheels) No evidence of excessive surface deterioration. The resistance to abrasion of production material shall be equal to or better than the material approved by the Materi

12、als Engineering Activity. ENGINEERING MATERIAL SPECIFICATION WSS-M5H40-A1/A2 Copyright 2015, Ford Global Technologies, LLC Page 3 of 5 3.4.5 Strength Properties 3.4.5.1 Breaking Strength 250N min (ASTM D5034 Grab Method, 300 mm/min speed Average of 5 samples in each direction) 3.4.5.2 Ultraviolet De

13、terioration (FLTM BO 116-01) 3.4.5.2.1 Retained tensile strength (ASTM D5034 Grab Method, 300 mm/min speed Average of 5 samples in each direction) Headliner application 225.6 kJ/m2 40% of original value,min Sun Visor and Pillar application 977.6 kJ/m2 40% of original value,min 3.4.6 Color Properties

14、 3.4.6.1 Resistance to Fade (FLTM BO 116-01, ISO 105-A02/AATCC Evaluation Procedure 1) Headliner application 225.6 kJ/m2 Rating 4, min Sun Visor and Pillar application 977.6 kJ/m2 Rating 4, min 3.4.6.2 Resistance to Heat Aging Rating 4, min (7 days at 100+/-2C, ISO 105-02/ AATCC Evaluation Procedure

15、 1) No individual yarn or combination of yarns shall exhibit fiber deterioration or color tone change in excess of the above rating. 3.4.6.3 Resistance to Crocking (FLTM BN 107-01, AATCC, Evaluation Procedure 2) Dry Rating 4, min Wet Rating 4, min 3.4.6.4 Soiling and Cleanability (FLTM BN 112-08, so

16、il only) Rating 4, min 3.4.7 Laminate 3.4.7.1 Adhesion Strength (flame bonded face fabric to foam) (FLTM BN 151-05, Method A, condition specified below) As received 6N min. Heat Aged (7 days at 100+/-2C) 6N min. Environmental Aging 6N min. Confirm with the affected Materials Engineering Activity for

17、 agreement prior to using test chambers with automated programmable test cycles for the listed test conditions below. Ramp speed 1 to 5 C per minute (record actual ramp speed on data sheet). ENGINEERING MATERIAL SPECIFICATION WSS-M5H40-A1/A2 Copyright 2015, Ford Global Technologies, LLC Page 4 of 5

18、. 5 h at -30 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at 90 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 16 h at 50 +/- 2 C and 95 +/- 5% R.H. . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at -30 +/- 2 C . 30 min at 23 +/- 2 C and 50% R.H. . 5 h at 90 +/- 2 C Autoclave 6N min. (ASTM D3574, TES

19、T J 2, two autoclave cycles of 5h at 120 C each) Applicable for all Tropical, Sub Tropical and NA Markets. The foam shall not separate cleanly from the fabric back (cohesive failure of foam required). Foam particles must be present on the fabric back. In the case when sustained peel cannot be obtain

20、ed due to the foam tearing, ply adhesion shall be considered acceptable and indicated as foam tear. If the laminate is less than 4mm thick and a numerical ply adhesion value cannot be satisfactorily obtained, ply adhesion shall be acceptable if the fabric cannot be separated cleanly from the foam. 4

21、. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WSS-M5H40-A1/A2 Copyrigh

22、t 2015, Ford Global Technologies, LLC Page 5 of 5 Table 1 Paragraph Sample Size Face Fabric Material Only Construction Approval Construction and Color Approval Face Fabric with Foam Laminate Face Fabric/Foam Composite with Substrate 3.3.1.1 Weight 3/avg. X X 3.3.1.2 Fabric Count 3/avg. X X 3.4.1 Odo

23、r 3 per condition X 3.4.2 Fogging 3 plates X 3.4.3 Flammability Headliner X Sun Visor X Pillar X-if not 100% bonded X-if 100% bonded 3.4.4 Resistance to Abrasion 3 X 3.4.5.1 Breaking Strength 5 W/5 F X 3.4.5.2.1 Retained Tensile Strength 5 W/5 F X 3.4.6.1 Resistance to Fade 1-Headliner X- 225.6 kJ/m2 1-Sun Visor X- 977.6 kJ/m2 1-Pillar X -977.6 kJ/m2 X -977.6 kJ/m2 3.4.6.2 Resistance to Heat Aging 1-Headliner X 1-Sun Visor X 1-Pillar X 3.4.6.3 Resistance to Crocking 1 per condition X 3.4.6.4 Soiling and Cleanability 1 soil only X 3.4.7 Laminate 3 avg per condition X