FORD WSS-M8P16-A-2010 PERFORMANCE CARPET FLOOR AND TRIM TO BE USED WITH FORD WSS-M99P1111-A 《地毯、地板和内饰的性能 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M8P16-B］》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 07 16 N-STATUS Replaced by WSS-M8P16-B L. Sinclair, NA 2006 12 08 Revised Inserted 3.0, 3.17.1 Deleted 3.1, 3.2, 3.3, 3.27, 3.28 Added filtered xenon requirement L. Sinclair1996 06 17 Activated Y. Alaniva, J. Williams Printed copies are u

2、ncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 6 PERFORMANCE, CARPET, FLOOR AND TRIM WSS-M8P16-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by this specification are automotive quality carpet assemblies, for floor, door trim, seat backs (front and any rear seat

3、 backs in exposed load compartment applications) and exposed load floors whether molded or otherwise fabricated. 2. APPLICATION This specification was released originally for passenger compartment floor coverings and other automotive trim applications. 3. REQUIREMENTS Material specification requirem

4、ents are to be used for initial qualification of materials. In addition to the requirements listed herein, the individual carpet assembly components shall meet all the requirements of the applicable material specifications for the carpet, padding, adhesive, barrier, or trim application. Heel pads, w

5、hen required, shall meet the requirements of WSS-M15P37-B. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 SAMPLE SELECTION All evaluations shall be conducted on

6、 test specimens taken from production representative carpet assemblies. If the specimen is taken from an area in the carpet with padding, the padding should be stripped away as much as possible before evaluation, unless otherwise specified. Test specimens for strength or abrasion properties shall be

7、 taken from molded or stressed areas of the carpet assembly (i.e., the footwell unless otherwise specified). 3.5 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.6 WEIGHT (FLTM BN 1

8、06-01) The weight shall be as specified in the individual materials specification or as designated on the engineering drawing. ENGINEERING MATERIAL SPECIFICATIONWSS-M8P16-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 6 3.7 COMPOSITION AND CONSTRUCTION Shal

9、l be as specified on the material specification and applicable engineering drawing describing the specific carpet. The padding shall be as specified on the engineering drawing and the individual padding specification. Backcoating: The backcoating shall form a continuous and uniform coating over the

10、back of the carpet so that all pile fibers are covered. Also, the backcoat shall show no evidence of cracking or crumbling during any of the evaluations required within the specification and during normal field conditions. The backcoat shall thoroughly saturate the base of the pile fiber bundles to

11、ensure adequate fiber lock. Penetration of the backcoat through to the face of the carpet shall be controlled to provide the required resistance to abrasion and fiber loss, but backcoat shall not be visible on the face of the pile fiber. Adhesion: The carpet material and padding shall be properly bo

12、nded together with the backcoating and/or adhesive where necessary, to ensure that the various components of the finished carpet assembly do not delaminate under normal handling and shipping operations. Secondary Backing Fabrics (if applicable): The secondary fabric shall be uniformly and continuous

13、ly bonded across the entire carpet and shall be free of voids and tears. 3.8 REQUIRED FOR ONGOING PRODUCTION VERIFICATION In addition to the following minimum requirements, production carpet assemblies must withstand normal handling during shipping and installation, without tearing. 3.8.1 Breaking S

14、trength, min (ASTM D 5034 Grab Method, 305 mm/minute jaw speed) Floor Other Trim WMD 400 N 300 N AMD 400 N 300 N 3.8.2 Tear Strength (Trapezoid), N, min, Dry and Wet (ASTM D 1117, Integration Method, average of 5 samples each direction) Floor Other Trim Min Ind. min Min Ind. min WMD 90 60 60 45 AMD

15、50 40 40 35 3.9 SHRINKAGE, WATER (FLTM BN 105-01) WMD Warp, max 2.0% AMD Weft, max 2.0% ENGINEERING MATERIAL SPECIFICATIONWSS-M8P16-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 6 3.10 HEAT SHRINKAGE, max (FLTM BN 105-01, except instead of water, use 7 day

16、s at 90 +/- 2 C) Floor & Trim Mass-backed WMD & AMD 2.0% 5.0% 3.11 RESISTANCE TO HEAT AGING, min Rating 4 (7 days at 90 +/- 2 C, ISO 105-A02/ AATCC Evaluation Procedure 1, use sample from para 3.10) No individual yarn or combination of yarns shall exhibit fiber deterioration or color tone change in

17、excess of the above rating. There shall be no visual deterioration of backcoating. 3.12 DIMENSIONAL STABILITY, max (FLTM BN 105-03, 2 cycles) WMD & AMD 2.0% 3.13 RESISTANCE TO ABRASION (SAE J1530-A, 1000 g load, H-18 wheels) If throw-in If throw-in mat optional mat standard Driver Footwell Area, cyc

18、les 4000* 2000 Remainder of Passenger Tufted 2000 cycles Compartment Floor Needled 1500 cycles The floor carpet shall be reviewed after 1000 cycles of abrasion and not show wear in excess of the material originally approved by Materials Engineering. *This abrasion resistance shall be provided by eit

19、her the carpet or by a driver heelpad. When a driver heelpad is used it must completely cover those areas most vulnerable to driver wear and must meet all requirements of WSS-M15P37-B. Trim application 500 g load H10 wheels Seat back, Exposed load floor (including 1200 cycles sidewalls) Load floor a

20、reas Door Panel 400 cycles The carpet shall exhibit no visual evidence of wear through to the foundation of the pile fibers in the abraded area. Production material shall be equal to or better than the material approved for production by Materials Engineering. ENGINEERING MATERIAL SPECIFICATIONWSS-M

21、8P16-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 6 3.14 RESISTANCE TO SNAGGING (needled carpets only) (SAE J1530-A, H-18 wheels, 500 g load) Passenger Compartment Floor Covering 200 cycles* Seat Backs, Door Panels & Exposed Load Floor 50 cycles No eviden

22、ce of fiber pullout in excess of the material originally approved by Materials Engineering. *Evaluate test specimen every 50 cycles. 3.15 ABRASION WEIGHT LOSS, max 0.20 gram (tufted floor carpets only) (SAE J1530-B, Method A, 1000 g load, H-18 wheels, 300 cycles, 4 samples) 3.16 PILE TUFT PULL STREN

23、GTH* (Tufted carpets only) (ASTM D 1335) 3.16.1 Room Temperature 10 N 3.16.2 Heated Tuft Pull at 80 C 10 N (Pull tufts with fixture in oven) 3.17 RESISTANCE TO FADE 3.17.1 Xenon Arc Weatherometer - Required Worldwide Except for North America (SAE J1885, ISO 105-A02/ AATCC Evaluation Procedure 1) Flo

24、or Carpets and Trim Carpets used Rating 4 below the armrest, 112.8 kJ/m2Trim Carpets used between the beltline Rating 4 and armrest, 225.6 kJ/m2Exposed Load Floor Carpets, 488.8 kJ/m2Rating 4 The material shall show no change in color tone and shall be equal to or better than the master samples appr

25、oved for production by the Materials Engineering Activity. ENGINEERING MATERIAL SPECIFICATIONWSS-M8P16-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 of 6 3.17.2 Filtered Xenon Arc Weatherometer Required for North America (SAE J1885 modified (FLTM BO 116-01) A

26、ATCC Evaluation Procedure 1 Floor Carpets and Trim Carpets used Rating 4 below the armrest, 225.6 kJ/m2Trim Carpets used between the beltline Rating 4 and armrest, 451.2 kJ/m2Exposed Load Floor Carpets, 977.6 kJ/m2Rating 4 The material shall show no change in color tone and shall be equal to or bett

27、er than the master samples approved for production by the Materials Engineering Activity. 3.18 FIBER DETERIORATION No excessive deterioration of fibers or yarns after the above xenon arc exposure. The resistance to deterioration of the production material shall be equal to or better than that exhibi

28、ted by the master sample approved by the Materials Engineering Activity. Test Method: Firmly apply a piece of 3Ms Highland Brand 6200 Permanent Mending Tape or equivalent to the surface of the exposed textile. Then rapidly strip the tape and mount it on a sheet of light or dark cardstock which contr

29、asts with the color of the fiber. Repeat the test with a new piece of tape on the unexposed sample and compare the length and quantity of fibers removed by the tape. Report fiber deterioration if a significantly larger number of fibers (usually of shorter lengths) are removed from the exposed versus

30、 unexposed sample. 3.19 RESISTANCE TO BLEEDING Rating 4 (FLTM AN 101-01, AATCC Evaluation Procedure 3) 3.20 RESISTANCE TO RUBBING (Crocking) (FLTM BN 107-01, AATCC Evaluation Procedure 3, use instrumental method FLTM BN 107-02, when color transfer is visually apparent) Rating Dry 4 (7.0 Delta E maxi

31、mum) Distilled Water 4 (7.0 Delta E maximum) If an instrument with diffuse geometry is used, the specular component of reflectance shall be included in the measurement. Note: If a crock result is greater than 7.00 DE, repeat the colorimeter measurement four (4) additional times and average all five

32、(5) results to minimize measurement error. The average must be less than or equal to 7.00 DE. DO NOT conduct another crock test on the roll unless examination of the original crock cloth indicates the test was conducted improperly (e.g., uneven pressure of the crock finger). ENGINEERING MATERIAL SPE

33、CIFICATIONWSS-M8P16-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 6 of 6 3.21 SOILING AND CLEANABILITY (FLTM BN 112-08, ISO 105-A02/ AATCC Evaluation Procedure 1) After Cleaning, min Rating 3 3.22 COLD RESISTANCE (mass-backed carpet assemblies only) (SAE J323,

34、Method A, 24 h at 90 +/- 2 C preconditioning, 24 h at -30 C and 6 mm mandrel, carpet face down) No evidence of cracking or delamination. 3.23 RESISTANCE TO MILDEW The material shall exhibit no visible evidence of mildew growth and/or objectionable odor after 7 days exposure in a humidity cabinet mai

35、ntained at 98 +/- 2% relative humidity and 38 +/- 2 C. 3.24 ODOR, max Rating 2 (FLTM BO 131-01/SAE J1351 except 1 liter glass jars) 3.25 FOGGING (SAE J1756, 3 h at 100 C heating, 21 C cooling plate, post test conditioning 1 h and 16 h) Fog Number, min 70 Formation of clear film, droplets or crystals is cause for rejection. 3.26 FLAMMABILITY (SAE J369/ISO 3795) Burn Rate, max 100 mm/minute