FORD WSS-M97B44-D2-2016 COOLANT ORGANIC ADDITIVE TECHNOLOGY (OAT) PRE-DILUTED FOR PASSENGER CAR AND LIGHT TRUCK TO BE USED WITH FORD WSS-M99P1111-A .pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 5 2016 05 12 Revised See Summary of Revisions A. Reaume, NA 2013 07 30 Reactivate Revised and re-activated spec. Replaced E2 M.Ranger; A.Reaume, FNA 2009 10 20 Activated A. Reaume, FNA Controlled document at www.MATS Copyright 2016, Ford

2、 Global Technologies, LLC Page 1 of 5 COOLANT, ORGANIC ADDITIVE TECHNOLOGY (OAT), WSS-M97B44-D2 PRE-DILUTED, FOR PASSENGER CAR AND LIGHT TRUCK 1. SCOPE The material defined by this specification is a pre-diluted coolant mix based on WSS-M97B44-D coolant and purified water. This coolant is specified

3、for plants that do not have sufficient water quality or the purification equipment required to properly condition the water. This coolant is also specified for use in post-production (service). Water quality will be monitored by the terminal mixing site. 2. APPLICATION WSS-M97B44-D2 is targeted to b

4、e a 50/50 pre-diluted engine coolant for plant fill. This material was originally released for passenger car and light truck applications in areas where plant water quality would affect coolant performance. This material is also released for post -production (service) at 50/50 and other concentratio

5、ns, depending on region, in order to ensure coolant quality. 3. REQUIREMENTS Ford Motor Company reserves the right to subject candidate coolants to any investigation they may consider necessary and use the data derived for approval qualification. 3.1 DOCUMENTATION Supplier must furnish to the affect

6、ed Materials Engineering activity a completed and certified copy of the attached supplements A and B and test reports demonstrating full compliance with all the requirements of this specification along with the manufacturing limits that apply to the material upon which approval is requested. All tes

7、ts must be certified by a qualified and authorized representative of the test facility. In addition, approval for a local blender supplying formulation blended from a superconcentrate (of an approved formulation) is contingent upon initial approval of the formulation with surrogate test data where a

8、pproved by Ford and testing and documentation, at minimum, in the attached PVP ASTM D1384 and ASTM D4340. 3.2 COOLANT COMPOSITION Coolant must meet WSS-M97B44-D and be approved on the Ford Approved Source List. This specification requires the use of approved sources. Only the sources identified on t

9、he Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.3 CONDITIONING AND TEST CONDITIONS All test values are b

10、ased on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. ENGINEERING MATERIAL SPECIFICATION WSS-M97B44-D2 Copyright 2016,

11、 Ford Global Technologies, LLC Page 2 of 5 3.4 FREEZE POINT OF SOLUTION -37C max (ASTM D1177/D3321) 3.5 WATER QUALITY Water used in coolant dilution must meet the requirements of WSS-M99P25-C. Post production (service) in North America must also meet current ASTM D3306 requirements. Continuous water

12、 quality monitoring shall be used at the terminal blending site. 3.6 BATCH ACCEPTANCE CRITERIA Shipments to vehicle assembly plants shall conform to Vehicle Operations General Office Bulletin VOPQU-236, Surveillance and Control of Fluids. Specifically for engine coolant Concentrate. Supplement A, Su

13、pplier Certification Statement is also required. 3.7 HEALTH AND SAFETY The coolant supplied to this specification must not contain any nitrosoamine or triethanolamine or any other compound that, in the presence of nitrate, or nitrite, nitrogen oxides, or other nitrosating substance, might product a

14、nitrosoamine. 3.8 POST PRODUCTION (SERVICE) COOLANT Post-production(service) coolant concentration may be based on the regional requirements shown in paragraph 3.9 PRODUCTION COOLANT CONCENTRATION of WSS-M97B44-D. Concentration must not exceed 50% or be less than the Minimum Coolant Concentration sh

15、own. Coolants shall meet all other requirements of this specification, except paragraph 3.4 if the concentration is other than 50/50. Coolants in North America shall meet the current ASTM D 3306 Type III coolant requirements. A copy of ASTM D3306 certification will be required in North America. Cool

16、ants must also meet the specific requirements of Ford Customer Service Division (FCSD). Supplier must work with FCSD and upon request furnish to FCSD all requested supporting documentation. 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting th

17、e requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering

18、. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon re

19、quest and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.2 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characte

20、ristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (

21、STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. ENGINEERING MATERIAL SPECIFICATION WSS-M97B44-D2 Copyright 2016, Ford Global Technologies, LLC Page 3 of 5 For parts and compon

22、ents using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.3 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions

23、imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing ba

24、sis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS 2016 05 12 Revised 2 and 3.8 for service concentrations other than 50%. Added in standard paragraphs 2013 07 30 Revised and re-activated spec. Replaced E2 Rationale: The WSS-M97B44-D2 specification number was published in many global do

25、cuments and service manuals. In order to minimize the disruption of updating this literature, the updates made in E2 were captured in the D2 level specification. The D2 level specification was reactivated from “N” (Not for new design) status in MATS. The approved sources were realigned to this revis

26、ion. 2012 09 19 N Status spec; Replaced by WSS-M97B44-E2 2012 04 16 Corrected typo in release year from 2011 to 2012. 2011 06 28 Revised - Corrected ASTM reference in para 3.5 ENGINEERING MATERIAL SPECIFICATION WSS-M97B44-D2 Copyright 2016, Ford Global Technologies, LLC Page 4 of 5 Supplement A, p.

27、1 of 1 SUPPLIER CERTIFICATION STATEMENT ENGINE COOLANT PRE-DILUTED FORD SPECIFICATION WSS-M97B44-D2 certifies that pre-dilute engine (Supplier Company) coolant identified as Lot/Batch No. and shipped to the plant conforms to the following requirements of Material Specification WSS-M97B44-D2 to which

28、 we are an approved supplier. Test results for this coolant lot are as follows: SUPPLIER ITEM TEST METHOD SPEC RANGE RESULTS pH, undiluted ASTM D1287 _ _ Reserve Alkalinity, ml ASTM D1121 _ _ ( Titrated to 4.5 ) Specific Gravity, ASTM D1122 _ _ 20/20OC Freeze Point, C ASTM D1177 _ _ undiluted Color Visual _ _ Suspended Material Visual _ _ This shipment totals _ gallons and was delivered via _carrier. Authorized Signature _ Title _ Plant _ ENGINEERING MATERIAL SPECIFICATION WSS-M97B44-D2 Copyright 2016, Ford Global Technologies, LLC Page 5 of 5 Supplement B, p. 1 of 1 PVP&R FORM