FORD WSS-M99J291-B5-2008 TAPE NON-TOPCOATED URETHANE PRESSURE SENSITIVE CHIP RESISTANCE NON- VISIBLE APPLICATIONS FOR HIGH IMPACT AREAS TO BE USED WITH FORD WSS-M99P1111-A 《室外高紫外.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Ver 1 2008 06 20 Activated M. Jones, FNA Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 1 of 6 TAPE WITH CLEARCOAT, URETHANE, PRESSURE SENSITIVE, CHIP WSS-M99J291-B1 RESISTANT, EXTERIOR, HIGH UV FOR HIGH IM

2、PACT AREAS TAPE WITH CLEARCOAT, URETHANE, PRESSURE SENSITIVE, CHIP WSS-M99J291-B2 RESISTANT, EXTERIOR, LOW UV FOR HIGH IMPACT AREAS TAPE WITH CLEARCOAT, URETHANE, PRESSURE SENSITIVE, CHIP WSS-M99J291-B3 RESISTANT, EXTERIOR, HIGH UV FOR MODERATE IMPACT AREAS TAPE WITH CLEARCOAT, URETHANE, PRESSURE SE

3、NSITIVE, CHIP WSS-M99J291-B4 RESISTANT, EXTERIOR, LOW UV FOR MODERATE IMPACT AREAS TAPE, NON-TOPCOATED, URETHANE, PRESSURE SENSITIVE, CHIP WSS-M99J291-B5 RESISTANCE, NON- VISIBLE APPLICATIONS FOR HIGH IMPACT AREAS TAPE, NON-TOPCOATED, URETHANE, PRESSURE SENSITIVE, CHIP WSS-M99J291-B6 RESISTANCE, NON

4、- VISIBLE APPLICATIONS FOR MODERATE IMPACT AREAS 1. SCOPE The material defined by these specifications is a clear, release liner backed, abrasion resistant urethane film with a water clear pressure sensitive adhesive. Films B1 - B4 include a clearcoat applied over the urethane film to prevent film s

5、taining, yellowing, and increases weathering performance. Films B5 and B6 are typically not clearcoated. To differentiate between locations requiring chip resistant testing, a CAE model or equivalent will be used to determine chip performance based on vehicle design. Ford engineers will determine ar

6、eas of high and low chip probability. 2. APPLICATION These specifications were released to provide localized stone chip protection on painted body surfaces. A clean surface is recommended for tape application. A wetting solution (25% isopropyl alcohol/75% deionized water or S-802 Decal Lube or equiv

7、alent) may be recommended by the supplier to aid in application. Tape dimensions and premask (with or without) are specified on the engineering drawings. 3. REQUIREMENTS All testing to be done on finished production parts (i.e., film to be used to design intent and application on production substrat

8、e/paint). Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). ENGINEERING MATERIAL SPECIFICATION WSS-M99J291-B1/B2/B3B/B4/B5/B6 Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 2 of 6 3.

9、1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 CONSTRUCTION 3.2.1 Width and Length As specified on engineering drawing. 3.2.2 Premask As specified on engineering

10、drawing. 3.3 FILM PROPERTIES Test Conditions: Material shall be conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity for not less than 24 hours prior to testing and tested under the same conditions unless otherwise specified. 3.3.1 Appearance 3mm diameter - Evaluate p

11、aint surface by peeling half the urethane from the panel. - No paint chipping allowed - Paint scuff rating 6A 9A, SAE J400 Fig 3 -30 C Evaluation: - No continuous film lift 10mm 3.4.7.2 1.41 L gravel B3/B4/B6 (SAE J400, 4” X 6” tape sample) 23 C Evaluation: - No film lift 3mm diameter - Evaluate pai

12、nt surface by peeling half the urethane from the panel. - No chipping allowed - Paint scuff rating 6A 9A, SAE J400 Fig 3 -30 C Evaluation: - No continuous film lift 10mm 3.4.8 Shrinkage, Max. 1% Test Method: Expose sample in a mechanical convection oven for 30 minutes at 120 +/- 2C. The test shall b

13、e conducted 2 h after application of 25 x 100 mm strip of the material to a test panel. This test shall be conducted in both machine and cross-machine directions. 3.4.9 Storage Stability B1-B4 B5/B6 3.4.9.1 180 Peel Adhesion, Min. 450N/m 300N/m (Store samples for 72 h at 73 +/- 2 C and test per sect

14、ion 3.5.1.1) ENGINEERING MATERIAL SPECIFICATION WSS-M99J291-B1/B2/B3B/B4/B5/B6 Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 6 of 6 3.5 FINISHED PART REQUIREMENTS Color and uniformity Smoothness (absence of blisters) Absence of scratches and tool marks Match to p

15、rint dimensions 3.7 FUNCTIONAL APPROVAL Materials being evaluated for approval to this specification shall be subjected to a production trial. Functional trial results must be approved by the affected assembly operation and Design Engineering. Results shall be made available to Materials Engineering

16、 prior to material approval and release. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of these specifications. 4.1 Painted electrocoated steel panel: Use current production paints as specified by Vehicle Operations Paint

17、Engineering. Process panels at minimum engineering specification requirements for primer and topcoat thickness, target bake temperature. 4.2 Painted ESB-M3D145 SMC panels with ESB-M6J106 conductive primer: Use current production paints as specified by Vehicle Operations Paint Engineering. Process panels at minimum engineering specification requirements for primer and topcoat thickness, target bake temperature.