GMKOREA EDS-M-6067-2010 TRICOT FABRIC FOR HEADLINIG.pdf

1、 GMDAT ENGINEERING STANDARDS Material Specification Textiles SUPERCEDED EDS-M-6067 Tricot Fabric for Headlining This standard may be applied only for current project. It is Superceded for all future projects and replaced by GMW14231. G&(8$7 C*C :,p Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program .B

2、d# GMW14231 ) $4=F7 957F$ . Copyright 2010 General Motors Company All Rights Reserved September 2010 Originating Department: GMDAT Engineering Standards Page 1 of 5 Version : 3 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict be

3、tween the Korean and English language, the Korean language shall take precedence. 1.1 Purpose. This specification specifies the requirements of basic property for Tricot fabrics used for headlining of automobiles. 1.2 Material Description. Non-raised type tricot fabric flame laminated with polyethyl

4、ene film on the polyurethane foam. 1.3 Typical Applications. This specification is applied to the Non-raised type tricot fabric flame laminated with polyurethane foam and polyethylene film on the backing used for headlining. 2 References Note: Only the latest approved standards are applicable unless

5、 otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. EDS-M-0102 EDS-T-7402 EDS-T-7602 EDS-T-7611 EDS-T-7624 EDS-T-7647 EDS-T-7694 GMW3059 EDS-T-7132 EDS-T-7415 EDS-T-7603 EDS-T-7614 EDS-T-7625 EDS-T-7683 GMW3001 2.3 Additional References. None 1 P7 :0 :

6、 E:48 6&F !7$ :4-8! 9I8x $4=F 3L 6$ . :0 : F67t 7568 18 88x 7 , F6* 72T8p) F$ . 1.1 +95 . ., E:48t 8% = !88:E G&(8$7 17F# C*C 8$ (Tricot Fabric)8 ,p2e8x G*F E:8x 4*F#$ , +958 8$ . 1.2 8: 8-L C2e . Polyurethane Foam 7 PE Film 8 . w 9E=%P Non-d+ Type C*C 8$ (Tricot Fabric). 1.3 957 -88 . ., E:48t 8%

7、 =8 !88:E G&(8$7 17Fd 88F 8+7 E(*7)07 38%P E:48x 957F$ . 2.1 17 E:4 / . F$-1F 68 2.2 GM E:4 / . EDS-M-0102 EDS-T-7402 EDS-T-7602 EDS-T-7611 EDS-T-7624 EDS-T-7647 EDS-T-7694 GMW3059 EDS-T-7132 EDS-T-7415 EDS-T-7603 EDS-T-7614 EDS-T-7625 EDS-T-7683 GMW3001 2.3 dA E:4 / . F$-1F 68 GMDAT ENGINEERING STA

8、NDARDS EDS-M-6067 Copyright 2010 General Motors Company All Rights Reserved September 2010 Page 2 of 5 Version : 3 3 Requirements 3.1 General Properties 3 7 1F 3.1 d., ,p2e Table 1: General Properties / E 1: d., ,p2e Designations / 4G F+ Test Methods / 4G - Specifications / 3.1.1 Weight per unit are

9、a (Total). / $88 +95 $- :E( (Total). EDS-T-7611 280 g/m2 min. / 280 g/m2 81 . 3.1.2 Thickness (Total). / % (Total). EDS-T-7624-4D 3.60.3 mm. 3.1.3 Structure. / 9 . 3.1.3.1 Fabric cover. 3.1.3.1.1 Weight per unit area. / $88 +95 $- :E( . 3.1.3.1.2 Thickness. / % . 3.1.3.1.3 Weave density. / :9 -4$ .

10、3.1.3.1.3.1 Wales. / 1 . 3.1.3.1.3.2 Courses. / 881 . EDS-T-7611 EDS-T-7624-4D EDS-T-7683 130 g/m2 min. / 130 g/m2 81 . 0.6 mm min. / 0.6 mm 81 . R 16Wales/cm. R 16Coures/cm. 3.1.3.2 Polyurethane foam. / E(*7)4 7 1F 3.2.1 dA 82lF 1F8t .E $+8x =l9 F GMDAT ENGINEERING STANDARDS EDS-M-6067 Copyright 20

11、10 General Motors Company All Rights Reserved September 2010 Page 4 of 5 Version : 3 3.2.2 Color of the fabric in the same lot shall be the same, and its appearance shall be in accordance with the master sample distributed by GMDAT Technical Center. 3.2.3 The fabric delivered for production shall sh

12、ow no discrepancy with the determined pattern and the warping or inclination of the patter shall not exceed 2.0%. 3.2.4 All the materials subject to this standard shall have pollution resistance. Use of commercial cleaning agents shall cause no permanent detrimental changes, pollution or color chang

13、es on the surface. 3.3 Approval and Quality Assurance Procedure. All raw materials shall be approved and regularly inspected for its quality prior to and during mass production delivery according to approval and quality assurance procedure for chemical raw materials (Spec. No. EDS-M-0102) 4 Manufact

14、uring Process Not applicable. 5 Rules and Regulations 5.1 All materials supplied to this standard must comply with the requirements of GMW3001, Rules and Regulations for Material Specifications 5.2 All parts or systems supplied to this standard must comply with the requirements of GMW3059, Restricte

15、d and Reportable Substances for Parts. 6 Approved Sources Not applicable. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: EDS-M-6067 3.2.2 % 8 )C72P 21%P

16、8$ (Fabric)8 11 -C ,p2e8t % 8F7 6 F+ , , 740 9: 9# $-1 d3T7$ 272P 38 -dE %P E:4., (Master Sample)7 :4F$ . 3.2.3 61 )=E8t 9IF: DBh0 $ (2P# 6|%L+ , DBh8 H D# 1 7X=# 2.0%* “L62P# 6| %P$ . 3.2.4 ., E:47 8F7 957%L# 8:8t 7X70 94F2e8 866 F$ . B1958 2l9P8 17 4 748 75 95 -G , 7X70 -C dA 118 -G* 88pA: 66x6 F$ . 3.3 38 -C E:.(: 9) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 SEP 2010 Superceded (Appearance Material Engineering Team) / F9I957 =* (Appearance Material 2XD4 )