GMKOREA EDS-M-6684-2011 5% Barium Sulphate Filled High Density Polyurethane Foam.pdf

1、 ENGINEERING STANDARDS Material Specification SUPERCEDED EDS-M-6684 5% Barium Sulphate Filled High Density Polyurethane Foam This standard may be applied only for current project. It is Superceded for all future projects and replaced by GMW14196. G1-H* 5% : -4$ E(*7): -4$ E(*7)07 38%P E:48x 957F$ .

2、2.1 17 E:4 / . ASTM D638 2.2 GM E:4 / . EDS-M-0102 EDS-T-7301 EDS-T-7403 EDS-T-7423 EDS-T-7521 EDS-T-7673 GMW3059 GMW3116 2.3 dA E:4 / . TMC003 Material Safety Data Sheet guidance documents GM KOREA ENGINEERING STANDARDS EDS-M-6684 Copyright 2011 General Motors Company All Rights Reserved June 2011

3、Page 2 of 4 Version : 2 3 Requirements 3.1 General Properties. 3 7 1F 3.1 d., ,p2e . Table 1: General Properties / E 1: d., ,p2e Designations / 4G F+ Test Methods / 4G - Specifications / 3.1.1 Density. / -4$ . EDS-T-7673 2,000 kg/m3 3.1.2 Hardness. / $ . 3.1.2.1 As received condition without conditi

4、oning. / 98=* F: 68t 1B . 3.1.2.2 After 70 E 168 hours. / 70 E 168 hours G . EDS-T-7403 90 Shore A 90 Shore A 3.1.3 Tear strength. / 87( I$ . 3.1.3.1 As received condition without conditioning. / 98=* F: 68t 1B . 3.1.3.2 After 70 E 168 hours. / 70 E 168 hours G . EDS-T-7521-E 35 KN/m 30 KN/m 3.1.4 T

5、ensile strength (width: 13, Thickness: 3mm). / 88 I$ (width: 13, % : 3 mm). 3.1.4.1 As received condition without conditioning. / 98=* F: 68t 1B . 3.1.4.2 After 70 E 168 hours. / 70 E 168 hours G . ASTM D638 8 N/mm2 8 N/ mm2 3.1.5 Tensile extension (width: 13, Thickness: 3mm). / 88 48 (width: 13, %

6、: 3 mm). 3.1.5.1 As received condition without conditioning. / 98=* F: 68t 1B . 3.1.5.2 After 70 E 168 hours. / 70 E 168 hours G . ASTM D638 100 % 50 % 3.1.6 Cold resistance (Change of hardness). / !F2e ($ -G ). EDS-T-7423-B1 (-30 E 5 hours) +20 Shore A max. / $4 +20 Shore A. 3.1.7 Residue on igniti

7、on (ash). / 7$2 8*( . EDS-T-7301 (62) % Note: All the mechanical, thermal and general property values above indicate minimum values except having the specified ranges. / :0 : 1d ,p2e F+ :E C-H ,p2eF -88* :9IF: 68t 7 +% 2F8x !A! . 3.2 Test Piece and Test. 3.2.1 Test piece. Test pieces shall be prepar

8、ed with injection molding. Unless otherwise specified in the requirements of section 3, they shall be conditioned at 23 E 5K and a relative humidity of 50% for 24 hours or more. 3.2.2 Test. Tests shall be performed at 23 E 5K and a relative humidity of 50 %. 3.2 4G D -C 4G . 3.2.1 4G D . 3 F8 7 1F72

9、P C-F 6=8 68p+ 23 E 5K, 50% 1$43$ F72P 24 48 81 4G D8x 98=* F$ . 3.2.2 4G . 4G 8t 23 E 5K, 50 % 1$4 3$ F72P 44F$ . GM KOREA ENGINEERING STANDARDS EDS-M-6684 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 3 of 4 Version : 2 3.2.3 Further details, see part drawings. 4 Manufac

10、turing Process Not applicable. 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the Korean and English language, the Korean language shall ta

11、ke precedence. 5.3 Inspection and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering department prior to commencement of delivery of bulk

12、 supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the responsibility of the supplier to inform the cu

13、stomer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier prior to commencement of delivery of non-confor

14、ming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production samples have been approved by the appropriate Mate

15、rials Engineering department(s) as meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurred, a complete copy of the Material Safety Data She

16、et/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in compliance with specific country General Motor

17、s TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 3.2.3 dA 82lF 1F8t .E $+8x =l9F . 4 9P9 )9I18 775 9 F$-1F 68 . 5 ?0 9I 5.1 -*1 9I . +& 8*# F$- 472P 170 4) , 8TGF 957 4#F :4- , ? , 9I -C 1F8x +94P6 F$ . 5.2 66 . F67t 7568 18 88x 7 , F6* 72T8p) F$ . 5.3 1 -C -

18、L)X . GM 8-LE:47 8F 9P%P .E8! 8*8 4G D8t ., 8-LE:47 9I%P 4G 8x 7 98x +94P6 F+ , 61 )= 987 :04 .2P8 388x -O6x6 F$ . &H88 , d# , 22e , 9P9 )9I ,* /D# 21: &%0 4)%P 6&F -8($ -P2%T 7 , 1)7 388x -O6x6 F$ . $* F84 6# F , 8-L958p) 4 4=8x F6 F$ . -$8 GE84 6# F , )=8# 38%L: 68t 9PE8 61 )= 987 +& F$- 4G 8x -L.

19、) 3LFF 0* ,l2PGF6 F$ . 8. 77 86 :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 5.4 FF2P# 6| %P$ . 5.5 ,p:6|98.(8* / 6|98.(8* (MSDS/SDS). 49PE8 )= D# d97 )=%L# 9PE ! GF,p: 92e8 -%P 7 , GF ,p: .* y E47 4F 2l 9G 43B (GHS) D# 5 :7!- ,p:6|98.(8* / 6|98.(8* 7 1F8x +9F# ,p:6|98.(8* / 6|98.(8* 9PF6+ F$ . 49

20、58p) 9PE8 ,p:6|98.(8* / 6|98.(8*# GM8 ,p:6|98.(8* / 6|98.(8*7 4F :?8 TMC0038 7 1F8x :43LF6+ F$ . GM KOREA ENGINEERING STANDARDS EDS-M-6684 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 4 of 4 Version : 2 5.6 All materials supplied to this standard must comply with the requ

21、irements of GMW3059, Restricted and Reportable Substances for Parts. 6 Approved Sources Engineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File under this standard number have been qualified by Engineering as meeting the requireme

22、nts of this standard. For other GM locations, the responsible Engineering group should be contacted to obtain the approved source in that individual country. 6.1 Approval and quality assurance procedure. All raw materials shall be approved and regularly inspected for its quality prior to and during

23、mass production delivery according to approval and quality assurance procedure for chemical raw materials (Spec. No. EDS-M-0102). 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. GHS Globally Harmonized System MSDS Material Safety Data Sheet SDS Safety Data Sheet 8 Cod

24、ing System This standard shall be referenced in other documents, drawings, etc., as follows: Material per EDS-M-6684 9 Release and Revisions This standard was originated in May 2006. It was first approved by Polymer / Organic Material Lab Team in May 2006. It was first published in May 2006. 5.6 .,

25、E:47 9P4%P +& 8:&8t GMW3059 (8TF,p: 179P )8 9P* &d(6 F$ . 6 38 6= 8 E:48t 38%P 6=7 $4F d3T95 :8x 7F$ . 8 E:47 8F d3T958 :8 7x*%P GM 88 +2l7 !7(%P 6=+8 8 E:48 7 1F8x 94A$ . $* :7!7 88?F GM 8 7 , F$- 4-) 38%P 6= 9I.(* 83LFd 88F2P# F$- :04 .2P7t GE8F6 F$ . 6.1 38 -C E:.(: 9) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 2 JUN 2011 Apply new Engineering Standard Template and change the referenced test standards. Superceded (Polymer / Organic Material Lab Team) / 4 d3TE:4 64 957 -C 957 4G - - . F9I957 =* (G)8*4G D4 )