GMKOREA EDS-M-8014-2011 Oil-Synthetic Trans (GETRAG 240).pdf

1、 ENGINEERING STANDARDS Material Specification LIMITED USE EDS-M-8014 Oil-Synthetic, Trans (GETRAG 240) Do Not Use on New Program; No Replacement. 3L%C(3-,2 7X8 (GETRAG 240) Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program 72P# 957%L: 6#$ . Copyright 2011 General Motors Company All Rights Reserved Ju

2、ne 2011 Originating Department: GM Korea Engineering Standards Page 1 of 5 Version : 5 1 Scope 1.1 Material Description. Full synthetic gear oil manufactured from Polyglycol base. 1.2 Typical Applications. This specification specifies the general requirements of manual transmission oil used for manu

3、al transmission (GETRAG 240). 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. EDS-M-0102 EDS-T-7401 EDS-T-7705 EDS-T-7706 EDS-T-7717 EDS-T-7718 EDS-T-7725 EDS-T-7729 EDS-T-77

4、41 EDS-T-7774 EDS-T-7903 GMW3059 2.3 Additional References. TMC003 Material Safety Data Sheet guidance documents 3 Requirements 3.1 General Properties. 1 P7 1.1 8: 8-L C2e . Polyglycol 8:8 100% F2e8T Base8 Gear Oil. 1.2 957 -88 . ., 8t 8% =8 3L%C(3-,2 (GETRAG 240)8 8XG7 957%L# +#6 C(3-,2 7X88 8-L958

5、 7 ?7 $4F7 9IF$ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . EDS-M-0102 EDS-T-7401 EDS-T-7705 EDS-T-7706 EDS-T-7717 EDS-T-7718 EDS-T-7725 EDS-T-7729 EDS-T-7741 EDS-T-7774 EDS-T-7903 GMW3059 2.3 dA E:4 / . TMC003 Material Safety Data Sheet guidance d

6、ocuments 3 7 1F 3.1 d., ,p2e . Table 1: General Properties / E 1: d., ,p2e Designations / 4G F+ Test Methods / 4G - Specifications / 3.1.1 Density (g/ml). / -4$ (g/ml). EDS-T-7903 1.040 ) 1.050 3.1.2 Flash Point ( E ). / 8G9D ( E ). EDS-T-7741 230 min. / 230 81 . GM KOREA ENGINEERING STANDARDS EDS-M

7、-8014 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 2 of 5 Version : 5 Designations / 4G F+ Test Methods / 4G - Specifications / 3.1.3 Pour Point ( E ). / 8T% 9D ( E ). EDS-T-7717 (-40) max. / (-40) 8F . 3.1.4 Kinematic Viscosity (cSt). / % 9D$ (cSt). EDS-T-7401 20 E : 395

8、 ) 420 40 E : 135 ) 165 100 E : 27 ) 31 3.1.5 4-Ball Test Welding Force (N). / !F:E2e (N). EDS-T-7706 2,400 min. / 2,400 81 . 3.1.6 Viscosity Index. / 9D$:3L EDS-T-7718 200 min. / 200 81 . 3.1.7 Water Content (wt%). / 3L.F( (wt%). EDS-T-7725 0.1 max. / 0.1 8F . 3.1.8 Heat Stability Behavior. / 7(6|9

9、I$ . EDS-T-7729-A (120 E u 72 hours) Evaporation loss (wt%): 3 max. Change of viscosity (%): 5 max. Heat stability: Neither gel nor precipitation. / :-P24 (wt%): 3 8F . 9D$-G (%): 5 8F . 682e1 : GelG -C ?98 68x . 3.1.9 Phosporous Content (wt%). / 8F( (wt%). - Report. 3.1.10 Foam Tendency (ml). / E2e

10、 (ml). EDS-T-7705-5.3 24 E : 20/0 max. 93 E : 50/0 max. 100 E : 20/0 max. / 24 E : 20/0 8F . 93 E : 50/0 8F . 100 E : 20/0 8F . 3.1.11 Anti Corrosive Behavior. / -=2e . EDS-T-7774-B (100 E 72 hours) No corrosion on the steel test sheet. Black stains on the brass are permissible but no corrosion is a

11、llowed. / Steel 4G D7 .4 68x . Brass 4G D8 8t -18t F7F! .4 68x . 3.1.12 Zinc Content (wt%). / 6x7$ F( (wt%). - Report. 3.1.13 Sulfur Content (wt%). / G F( (wt%). - Report. 4 Manufacturing Process Not applicable. 4 9P9 )9I18 775 9 F$-1F 68 . GM KOREA ENGINEERING STANDARDS EDS-M-8014 Copyright 2011 Ge

12、neral Motors Company All Rights Reserved June 2011 Page 3 of 5 Version : 5 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the Korean and En

13、glish language, the Korean language shall take precedence. 5.3 Inspection and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering departme

14、nt prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the res

15、ponsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier pri

16、or to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production sample

17、s have been approved by the appropriate Materials Engineering department(s) as meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurred, a c

18、omplete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in co

19、mpliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 5.7 Dont dump in a ditch, dr

20、ain, and river. 5 ?0 9I 5.1 -*1 9I . +& 8*# F$- 472P 170 4) , 8TGF 957 4#F :4- , ? , 9I -C 1F8x +94P6 F$ . 5.2 66 . F67t 7568 18 88x 7 , F6* 72T8p) F$ . 5.3 1 -C -L)X . GM 8-LE:47 8F 9P%P .E8! 8*8 4G D8t ., 8-LE:47 9I%P 4G 8x 7 98x +94P6 F+ , 61 )= 987 :04 .2P8 388x -O6x6 F$ . &H88 , d# , 22e , 9P9

21、)9I ,* /D# 21: &%0 4)%P 6&F -8($ -P2%T 7 , 1)7 388x -O6x6 F$ . $* F84 6# F , 8-L958p) 4 4=8x F6 F$ . -$8 GE84 6# F , )=8# 38%L: 68t 9PE8 61 )= 987 +& F$- 4G 8x -L.) 3LFF 0* ,l2PGF6 F$ . 8. 77 86 :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 5.4 FF2P# 6| %P$ . 5.5 ,p:6|98.(8* / 6|98.(8* (MSDS/SDS).

22、49PE8 )= D# d97 )=%L# 9PE ! GF,p: 92e8 -%P 7 , GF ,p: .* y E47 4F 2l 9G 43B (GHS) D# 5 :7!- ,p:6|98.(8* / 6|98.(8* 7 1F8x +9F# ,p:6|98.(8* / 6|98.(8* 9PF6+ F$ . 4958p) 9PE8 ,p:6|98.(8* / 6|98.(8*# GM8 ,p:6|98.(8* / 6|98.(8*7 4F :?8 TMC0038 7 1F8x :43LF6+ F$ . 5.6 ., E:47 9P4%P +& 8:&8t GMW3059 (8TF,

23、p: 179P )8 9P* &d(6 F$ . 5.7 F3L , -d3L , I7 -*: + . GM KOREA ENGINEERING STANDARDS EDS-M-8014 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 4 of 5 Version : 5 5.8 Dangerous Class. Petroleum grade 3 (according to the Korean fire prevention regulation). 6 Approved Sources E

24、ngineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, the responsible Engineering group should be

25、 contacted to obtain the approved source in that individual country. 6.1 Approval Material. 5.8 88G &%= . 9P 3 2Q8T* (2- 4F)m7 8F .* ). 6 38 6= 8 E:48t 38%P 6=7 $4F d3T95 :8x 7F$ . 8 E:47 8F d3T958 :8 7x*%P GM 88 +2l7 !7(%P 6=+8 8 E:48 7 1F8x 94A$ . $* :7!7 88?F GM 8 7 , F$- 4-) 38%P 6= 9I.(* 83LFd

26、88F2P# F$- :04 .2P7t GE8F6 F$ . 6.1 38 8* . Part No. Old P/No. Approved Supplier / 38 6= Approved Raw Material / 38 88* Remarks / /x 94545015 M-8014 ISU Oil & Chemical. / 83L8TG Synthetic transmission oil 75W140 6.2 Approval and Quality Assurance Procedure. All raw materials shall be approved and re

27、gularly inspected for its quality prior to and during mass production delivery according to approval and quality assurance procedure for chemical raw materials (Spec. No. EDS-M-0102). 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. GHS Globally Harmonized System MSDS

28、Material Safety Data Sheet SDS Safety Data Sheet 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Material per EDS-M-8014 In case that this material is applied as part number. The coding system shall be indicated as follows 6.2 38 -C E:.(: 9) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 5 JUN 2011 Apply new Engineering Standard Template. Limited use with no replacement (Polymer / Organic Material Lab Team) / 4 d3TE:4 64 957 . F9I957 ($4=E:4 68 ) =* (G)8*4G D4 )