GMKOREA EDS-T-2529-2011 Static Strength of Tension-Limiting Means of Hydraulic Vibration Dampers.pdf

1、 ENGINEERING STANDARDS General Specification SUPERCEDED EDS-T-2529 Static Strength of Tension-Limiting Means of Hydraulic Vibration Dampers This standard may be applied only for current projects. It is Superceded for all future projects and replaced by GMW14290. Copyright 2011 General Motors Company

2、 All Rights Reserved November 2011 Originating Department: GM Korea Engineering Standards Page 1 of 3 Version : 3 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the Korean and English language, the Korean language shal

3、l take precedence. 1.1 Purpose and Scope. This test specification defines the test conditions, courses and requirements for the static test of tension-limiting means of hydraulic vibration dampers. At this test, the strength of the junction stop ring - piston rod is tested. 2 References Note: Only t

4、he latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. DIN 51220 DIN 51221 DIN 51223 2.2 GM Standards/Specifications. GMW3059 2.3 Additional References. None 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 Calibration. The test facilitie

5、s and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definit

6、ion. 3.1.3 Test Piece. For the testing, the assembly piston rod-stop ring is used as test sample. If not differently specified, minimum 3 test samples are to be tested at initial sampling and in arbitrary cases, minimum 1 sample is for the current quality control. 3.1.4 Equipment. 3.1.4.1 Material -

7、 Testing Machine. A material-testing machine which must be so equipped that the test samples could be loaded with a steady speed of stressing of 5 mm/min max. The maximal test forces of the machine are guided by the requirements for the test. Suitable is a testing machine according to DIN 51220, DIN

8、 51221 Part 1 to 3 and DIN 51223. The testing machine must besides satisfy following requirement: y Accuracy of force measuring: 1 % of measured value. y Accuracy of deformation in extension: 0.01 mm. 3.1.4.2 A Coordinate Recorder (X-Y-Recorder) which plots the characteristic of force-way modificati

9、on of the sample. 3.1.4.3 Suitable Supporting Device. See Figure 1. GM KOREA ENGINEERING STANDARDS EDS-T-2529 Copyright 2011 General Motors Company All Rights Reserved November 2011 Page 2 of 3 Version : 3 y Hardness of the receiving planes: 650 HV, 30 min. 3.2 Conditions. 3.2.1 Environmental Condit

10、ions. The test is performed at +15 E to +35 E without primary treatment of sample. 3.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 3.3 Instructions. 3.3.

11、1 Test Arrangement. Figure 1 3.3.2 The piston ring loaded with a constant speed of 5 mm/min maximum to the force F and released again after then. Figure 2 3.4 Data. 3.4.1 The permanent setting F in mm at F/2 is ascertained from the curve of Force - Direction modification. 3.4.2 The piston ring and t

12、he stop ring are examined on possible damages and cracks. GM KOREA ENGINEERING STANDARDS EDS-T-2529 Copyright 2011 General Motors Company All Rights Reserved November 2011 Page 3 of 3 Version : 3 3.5 Safety. This standard may involve hazardous materials, operations, and equipment. This standard does

13、 not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 3.6 Documentation. Samples of components or mate

14、rial released to this standard shall be tested for conformity with the requirements of this standard and approved by the responsible GM Department prior to the start of delivery of production level components or materials. Any change to the component or material, e.g., design, function, properties,

15、manufacturing process and/or location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer, unsolicited, with documentation of any change or modification to the product/process, and to apply for a new release. If not otherwise ag

16、reed to, the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified or changed product. In some cases, a shorter test can be agreed to between the responsible GM department and the supplier. 4 Requirements and Procedure 4.1 Performance Re

17、quirements. 4.1.1 The test force comes to F = 12 KN. 4.1.2 The Permanent Set F may come to 0.2 mm max. 4.1.3 Any damages of cracks may not be exhibited. 4.2 Further Requirements. 4.2.1 For admitted supplier, conform to this test specification. 4.2.2 Other additional specifications see relevant drawi

18、ng. 5 Provisions for Shipping 6 Notes 6.1 Glossary. Not applicable. 6.2 Acronyms, Abbreviations, and Symbols. Not applicable. 7 Additional Paragraphs 7.1 All parts or systems supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Cod

19、ing System This standard shall be referenced in other documents, drawings, etc., as follows: EDS-T-2529 9 Release and Revisions This standard was originated in October 1995. It was first approved by Engineering Standard Committee in October 1995. It was first published in October 1995. Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 NOV 2011 Apply new Engineering Standard Template. Superceded (Chassis Subsystem Validation Team) / 4 d3TE:4 64 957 . F9I957 =* (Chassis.ED4D4 )