GMKOREA EDS-T-3245-2012 Test Standard for Door Check Assembly.pdf

1、 ENGINEERING STANDARDS General Specification SUPERCEDED EDS-T-3245 Test Standard for Door Check Assembly This standard may be applied only for current projects. It is Superceded for all future projects and replaced by CTS. $6 =A 62|/H* 4G E:4 Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program .Bd# CTS

2、 ) $4=F7 957F$ . Copyright 2012 General Motors Company All Rights Reserved February 2012 Originating Department: GM Korea Engineering Standards Page 1 of 5 Version : 3 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the

3、 Korean and English language, the Korean language shall take precedence. 1.1 Purpose. The aim of this standard is to evaluate the performance & durability of the door check and specifying the test procedure & specification. 1.2 Scope. This standard applies to plastic molding of door check assembly f

4、or passenger cars. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. EDS-T-7143 GMW3059 2.3 Additional References. None 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 C

5、alibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with res

6、pect to their physical definition. 1 P7 :0 : ., E:48 6&F !7$ :4-8! 9I8x $4=F 3L 6$ . :0 : F67t 7568 18 88x 7 , F6* 72T8p) F$ . 1.1 +95 . 8 E:48t $6 =A 8 2e# -C ! 2e8x D4Fd 88F 8p)2P , 4G 907 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . EDS-T-7143 GMW3059 2.3 dA E:4 / . None 3 4G :4/x -C D4

7、3.1 4G 88 . 3.1.1 9I . 4G 2X/x7t 8/x# 9P 2e#8x -PHLF 8TGF 9I Fx:8x J66 F$ . 3.1.2 $4= 3L$ . $4= 4G 42X0 8/x4 17%T 3L 8$ . ,) ! ., E:47 +d%P +& ?U9I -3L&8t , ,p*95 9I87 8 9IGF 9I%L66 F$ . GM KOREA ENGINEERING STANDARDS EDS-T-3245 Copyright 2012 General Motors Company All Rights Reserved February 2012

8、 Page 2 of 5 Version : 3 3.2 Conditions. 3.2.1 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 3.3 Safety. This standard may involve hazardous materials, opera

9、tions, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 3.4 Docu

10、mentation. Samples of components or material released to this standard shall be tested for conformity with the requirements of this standard and approved by the responsible GM Department prior to the start of delivery of production level components or materials. Any change to the component or materi

11、al, e.g., design, function, properties, manufacturing process and/or location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer, unsolicited, with documentation of any change or modification to the product/process, and to appl

12、y for a new release. If not otherwise agreed to, the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified or changed product. In some cases, a shorter test can be agreed to between the responsible GM department and the supplier. 4 Requi

13、rements and Procedure 4.1 Sample Preparation. 4.1.1 Samples must be greased according to requirements in drawing. 4.1.2 The fastening torque of fixing bolts must meet requirements in drawings. 4.2 Detent Torque. Under the equivalent vehicle condition, measure the operation torque at a reciprocation

14、peed of (155) sec/cycle and temperature of 23 E 5K, after 30 cycles of operation prior to test. The operation torque must meet requirements in drawings. The operation torque must be the mean value of five measurements. 3.2 8-L 9 . 3.2.1 4G 9 . .,E:48p).Bd-6!#7 1F8t $-188 F8F6 F+ , 4)$+ , 4G 2e952P ,

15、 .(2P&%7$+d%L66F$ . 3.3 6|987 $4F 7 9 . ., E:48t 88G ,p: , 86 , 8/x &%8x E FF 3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . 3.4 : 2P* 9P) . 8 E:47 8F 9P%P .E8! 8*8 4G D8t ., E:47 9I%P 4G 8x 7 98

16、x +94P6 F+ , 61 )= 987 GM :04 .2P8 388x -O6x6 F$ . .E8! 8*7 862P &H88 , d# , 22e , 9P9 )9I ,* /D# 21:7t 4)%P 6&F -8($ -P2%T 7 49PE 4* 7F$ . )=8# +88 7= 7 .7t 14 68 9PE /21 )9I 18 - Gm8t P97 4F 2P* 9P)F6 F+ 4 9PE 4 4=8x F6 F$ . $* F84 6# F , )=8# P9 Gm8t -%P 9PE8 )= 987 98= : 4G 8x -L.) 3LFF 0* ,l2PG

17、F6 F$ . 8. 77 86 GM :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 4 7 9 -C 4G 92 9I B7XA ) =F7 6 F$ . 4.2 8%B7XA . 4=7 :4F# 8= 972P 4G 987 30 G* 8% F G , (15r5) $4 70 Nm 8F866 F$ . 4.3.2 947 4G . (-30) E 8 7$72P 3 48 8T:F G , 1.5 . 8!7 ?U9IF 8%B7XA # $4 70 Nm 8F866 F$ . 4.3.3 !G 4G . 70 E 8 7$72P 1

18、20 48 8T:F G , (-30) E 8 7$72P 3 48 8T:F , 1.5 . 8!7 ?U9IF 8%B7XA # $4 70 Nm 8F866 F$ . 4.3.4 88 4G . Door Check * 8%B7XA ?U9I fixture (4.2 F =l9 )7 8= G Strap 7 +p: (6x*9! +p: )* 0.5 cc$E F Check * 8% F+2P 28d (Sound Level Meter) 888x ?U9IF$ . 8 4G 8t +p:$E G 30 G 8% 8x 1 Cycle) F7 3 Cycles* 44F7 $

19、+7 9P%P F8x +9F7 6 F+ Sound Level Meter # $80 M8 Setting F$ . y Time Weighting: Fast. y Frequency Weighting: A. y Sound Incidence: Random. y Display: Max. Hold. 4.4 0.F 4G . 4G E8x 4=7 :4F# ($6 H:* 8=F 1B ) 4G 8?7 8=F7 $64 7x98H 7(* 1B72P 4G E7 9I%P B7XA * 4F G , 4G E8t 8% 1 8TFF F -C D28 666 F$ . y

20、 Front Door: 325 Nm. y Rear Door: 300 Nm. GM KOREA ENGINEERING STANDARDS EDS-T-3245 Copyright 2012 General Motors Company All Rights Reserved February 2012 Page 4 of 5 Version : 3 Photo 2: Over Opening Test Equipment / 1: 2: 0.F 4G 8? 4.5 Corrosion Test. Conduct salt spray test for 144 hours accordi

21、ng to EDS-T-7143. The change of operation torque must be a maximum of 5 Nm, and there must be no noise. 4.6 Durability Test. Mount the sample the vehicle or durability test equipment. 4.6.1 Operate the sample at a frequency of maximum 80,000 cycles 12 cycles/min to the fully opened/closed position.

22、4.6.2 Conduct durability test a total of 80000 cycles, and conduct over-opening durability test during initial 5000 cycle of total cycle 4.6.3 In the over-opening durability test, when opening the door, the load must be a 150 N at vehicle latch position. 4.6.4 After the durability test, the change o

23、f operation torque must be not exceeded by 50 % of initial operation torque. 4.6.5 After the durability test, there must be no noise. 4.5 .4 4G . EDS-T-7143 7 &d*# 703L .,h 4G 8x 144 48 44F G , 8%B7XA 8 -G(8t r5 Nm 8!866 F+ , 8%88 D# .88 666 F$ . 4.6 ! 4G . 4G E8x 4=7 :4F# ! 4G 8?7 8=F$ . 4.6.1 $68

24、7x98 PE 88?: $4 12 G /.8 :0d) PE 8% F$ . 4.6.2 Q 80,000 G8 ! 4G 8x 44F+ , ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 FEB 2012 Apply new Engineering Standard Template. Superceded (Body & Ext. Subsystem Validation Team) / 4 d3TE:4 64 957 . F9I957 =* (Body & Ext. .ED4D4 )