GMW GMW14887-2011 Design For Six Sigma Requirement Issue 2 English《六标准差要求的设计 第2次出版(英文版本)》.pdf

1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW14887 Design For Six Sigma Requirement Copyright 2011 General Motors Company All Rights Reserved July 2011 Originating Department: North American Engineering Standards Page 1 of 2 1 Introduction Note: Nothing in this standard supercedes appli

2、cable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Scope. Design for Six Sigma (DFSS)/Robust Engineering is the method GM is using to assure high quality in critical systems of our vehicles. The DFSS p

3、rocess flows the customer requirements to the design and then it assures that the design satisfies these requirements with minimum variation. Participation in, and support of, a DFSS project will be required by all suppliers of subsystems or components where GM product engineering is doing a GM DFSS

4、 project or where requested by GM. A supplier may be expected to conduct their own DFSS/Robust Engineering project to support meeting GMs performance requirements. 1.2 Mission/Theme. Not applicable. 1.3 Classification. Not applicable. 2 References Note: Only the latest approved standards are applica

5、ble unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. GMW3059 3 Requirements 3.1 If required by the Program Management Team (PMT)/Product Development Team (PDT), a DFSS or Robust Engineering Process will be followed by the supplier and presented

6、 to GM on critical design specifications. These will be a subset of the specifications given as part of the Statement of Requirements (SOR). The PMT/PDT or DFSS team will indicate which requirements are the critical few and the supplier will be expected to take the following actions: 3.1.1 The suppl

7、ier will participate with the GM DFSS project team by attending project meetings, including training if needed. The supplier will support the project by providing the appropriate engineering requested by GM. 3.1.2 The supplier will be expected to provide to the GM team an estimate of the capability

8、of their design both the nominal output and the expected variation on the critical few requirements highlighted within the SOR. The estimate will be accompanied by the list of major design parameters (control factors) that were used in that design. 3.1.3 The estimate of the critical to quality (CTQ)

9、 variation will be accompanied by a list of variation parameters (noise factors) with both their means and standard deviations. These variation parameters should include the major process parameters that are monitored or controlled by supplier control plans. 3.1.4 The performance prediction, in supp

10、ort of the GM DFSS project, will be done early in the design process before validation hardware is available, or by the timing needed by the PDT. 4 Validation 4.1 General. The validation plan may need to be altered to reflect the findings, (i.e., significant noise factors) from the DFSS project and

11、will be updated by the GM PDT. 4.2 Validation Cross Reference Index. Not applicable. 4.3 Supporting Paragraphs. Not applicable. 5 Provisions for Shipping Not applicable. 6 Notes 6.1 Glossary. Not applicable. 6.2 Acronyms, Abbreviations, and Symbols. CTQ Critical to Quality DFSS Design for Six Sigma

12、PDT Product Development Team Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14887 Copyright 2011 General Motors Company All Rights Reser

13、ved July 2011 Page 2 of 2 PMT Program Management Team SOR Statement of Requirements 7 Additional Paragraphs 7.1 All parts or systems supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Coding System This standard shall be referenc

14、ed in other documents, drawings, etc., as follows: GMW14887 9 Release and Revisions This standard was originated in December 2005. It was first approved by Global Design for Six Sigma in May 2006. It was first published in June 2006. Issue Publication Date Description (Organization) 1 JUN 2006 Initial publication. 2 JUL 2011 Five year refresh. (GM Design for Six Sigma) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-