GMW GMW15530-2012 Installation and Removal Retention Load for Snap-In Fasteners Press-In and Retaining Force Issue 2 English.pdf

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW15530 Installation and Removal/Retention Load for Snap-in Fasteners Press-in and Retaining Force Copyright 2012 General Motors Company All Rights Reserved November 2012 Originating Department: North American Engineering Standards Page 1 of 8 1 Scope

2、 Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. To determine the assembly/disassembly characteristics of a snap-in fastener. 1.2 Foreword. 1.

3、2.1 This procedure evaluates the performance of a snap-in fastener when subjected to loads, constraints, and environments representative of the installation or disassembly process. Option A of this procedure is a general procedure to record all performance data representative of the installation or

4、disassembly process. Option B is a specific method to identify the Press-in Force and Retaining Force of a snap-in fastener. 1.2.2 Unless otherwise specified, any requirements or direction provided in the Test Request documentation will supercede this test procedure. 1.3 Applicability. This procedur

5、e applies to any joint using a snap-in fastener that is installed by the application of axial force without the use of mechanical tools. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 9513 2.2 GM Standards/S

6、pecifications. GMW2 GMW3221 3 Resources 3.1 Facilities. GM approved laboratory or location for this test procedure. 3.2 Equipment. 3.2.1 Slot table or other suitable surface. 3.2.2 Fixturing as required to fasten the joint in the manner specified by its design. 3.2.3 Arbor press or load frame. 3.2.4

7、 Load cell of appropriate capacity to measure the maximum anticipated load. 3.2.5 Linear measurement device capable of measuring test specimen displacement, e.g., high resolution linear variable displacement transducer, extensiometer, ultrasonic gage, leaf gage, etc. 3.2.6 Recording device for simul

8、taneous recording of load and displacement. 3.2.7 Device capable of performing the press-in and extraction operation at a maximum speed of 100 mm/minute (class 2 extensometer per ISO 9513 or equivalent or better). The overall accuracy of the force/load measuring equipment shall be 2% of the measured

9、 value. One side of the device shall be equipped with a clamping fixture capable of securely holding the fastener during the press-in and extraction operation. The other side of the device shall be equipped with a clamping fixture capable of securely holding the test panel. Copyright General Motors

10、Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserved November 2012 Page 2 of 8 Note: In principle other

11、 simplified test setups simulating the practical application of the fastener may be used, provided the resulting assembly/disassembly values are representative and can be accurately recorded. 3.2.8 Test Panel. If not otherwise specified in the test request documentation, an uncoated test panel made

12、from sheet steel to GMW2-M-ST-S shall be used. The steel test panel must be degreased with a cleaning agent which allows no water drop buildup. This test panel shall be provided with a reamed and deburred hole (both sides to not influence test direction) without chamfer of diameter per fastener draw

13、ing. In the area of the test hole, the thickness of the test panel shall be specified by the test requester. 3.2.9 Apparatus for conditioning to the appropriate requirements of GMW3221. 3.2.10 Environmental chamber with air circulation capable of maintaining required temperatures within 2 C. 3.3 Tes

14、t Vehicle/Test Piece. 3.3.1 A complete bill of materials of required test pieces will be specified in the test request documentation. 3.3.2 Unless otherwise specified, eight samples are to be used for this procedure. 3.4 Test Time. Calendar time: 2 days Test hours: 8 hours Coordination hours: 8 hour

15、s 3.5 Test Required Information. Test request documentation shall outline specific information and test parameters (reference Appendix A). 3.6 Personnel/Skills. Test technician shall be qualified on the basis of appropriate education, training, experience, and/or demonstrated skills. 4 Procedure 4.1

16、 Preparation. 4.1.1 If necessary, rework parts of the assembly to allow them to be mounted in the load frame or press. Any alteration of the parts must not change any characteristics of the parts that would be prevalent during installation or removal of the fastener. 4.1.2 Configure the instrumentat

17、ion to record load and displacement. 4.1.3 If not specified otherwise in the test request documentation, condition test pieces for initial sample approval and arbitration purposes according to GMW3221, Code B and do not condition test pieces for quality control tests (as-received condition). 4.2 Con

18、ditions. Conditions should be representative of those the test assembly would experience during regular production assembly and field service. 4.2.1 Environmental Conditions. Environmental conditions should be representative of those the test assembly would experience during regular production assem

19、bly and field service. When testing plastic fasteners, it may be desirable to repeat the tests at extreme environments common during assembly/disassembly (high temperature/high humidity, low temperature/low humidity) as these may affect the characteristics of the fastener. Nylon parts may need to be

20、 conditioned by immersion in water if parts are dry so that friction and flex modulus are representative of production parts. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certifi

21、cates, reports, etc. Loading and constraint conditions should represent those of the test assembly during production. 4.2.2.1 If not specified otherwise in the test request documentation, parts shall be tested under the following conditions: insertion force shall be measured at minimum hole size and

22、 maximum panel thickness, and removal force shall be measured at maximum hole size and minimum panel thickness. 4.3 Instructions. 4.3.1 Option A, Characteristic Installation and Disassembly Performance Data. 4.3.1.1 Record load-displacement data while installing the fastener into the test piece, and

23、 then while removing it, if requested. Use any fixturing and adapters necessary to accurately reproduce installation/removal conditions. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license fro

24、m IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserved November 2012 Page 3 of 8 4.3.1.1.1 Start the recording device and push the fastener through the entirety of its travel on the press or load frame. If possible, use a load or displacement

25、rate that is representative of how the fastener will be installed during regular production assembly or field service. Stop when it bottoms out, if applicable to the fastener is being tested. If the fastener being tested is a two stage design (such as a pushpin), place the fastener fully into the te

26、st hole by hand, then record the load and displacement required to fully seat the locking plunger. 4.3.1.1.2 Visually examine the parts for any deformation or damage that might have occurred as a result of the installation. 4.3.1.1.3 If requested, remove the fastener from the test piece while record

27、ing load and displacement. 4.3.1.1.4 Repeat 4.3.1.1.1 thru 4.3.1.1.3 for the required number of installations for each sample. 4.3.1.1.5 Repeat for each sample specified in step 3.3.1. 4.3.1.2 Visually examine the parts for any deformation or damage that might have occurred as a result of the test.

28、4.3.1.3 Photograph the test setup and test assemblies. 4.3.1.4 Record any visual, audible or procedural observations noted during the test. 4.3.2 Option B, Press-In Force and Retaining Force. 4.3.2.1 Press-in Force. Store test pieces and test panels for 1 h minimum at +23 C 5 C. 4.3.2.1.1 Clamp the

29、test piece and the test panel into the clamping fixture of the test device (3.2.7). Ensure that the clamping fixture for the snap-in fastener is in exact alignment with the hole of the test panel. 4.3.2.1.2 Run the test device at a uniform maximum speed of 100 mm/minute to press the snap-in fastener

30、 into the test hole. 4.3.2.1.3 Read and record the maximum force in newtons from the force indicator of the test device. 4.3.2.2 Retaining Force. Press the snap-in fastener into the test hole of the test panel. Note: Test piece and test panels from 4.3.2.1 can be reused for this test. 4.3.2.2.1 Stor

31、e test pieces and test panels for 1 h minimum at +80 C minimum. 4.3.2.2.2 Clamp the test piece and the test panel into the clamping fixture of the test device (3.2.7). 4.3.2.2.3 Run the test device at a uniform maximum speed of 100 mm/minute to separate the snap-in fastener from the test panel. 4.3.

32、2.2.4 Read and record the force in newtons from the force indicator of the test device when separation appears. 5 Data 5.1 Calculations. Not applicable. 5.2 Interpretation of Results. 5.2.1 Option A, B. When interpreting the test results, the following applies: 5.2.1.1 To pass the test for press-in

33、force, each press-in force single value shall be less than or equal to the required press-in force maximum value on the test request documentation (e.g., part drawing). 5.2.1.2 To pass the test for retaining force, each retaining force single value shall be greater than or equal to the required reta

34、ining force minimum value on the test request documentation (e.g., part drawing). 5.3 Test Documentation. 5.3.1 Option A. 5.3.1.1 Summary of Results - Required. 5.3.1.1.1 Test incidents to be recorded on Test Data Summary Sheet or similar (reference Appendix B). 5.3.1.1.2 Test data summarization to

35、be on Test Data Log Sheet or similar (reference Appendix C). 5.3.1.1.3 Provide load versus displacement plot for each sample evaluated with displacement on the X axis and load on the Y axis. 5.3.1.1.4 A table shall be prepared listing specimen identification, description, environment, test date, obs

36、ervations (if applicable), and installation and removal load values, mean minimum, maximum, standard deviation, and mean 3 standard deviations. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without lice

37、nse from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserved November 2012 Page 4 of 8 5.3.1.2 Summary of Results Optional. After reviewing required data summarization, requestor may ask for additional items including, but not limited to, the

38、 following: 5.3.1.2.1 Magnified Scale Plots - additional plots re-scaled to magnify desired detail of curves. 5.3.1.2.2 Optional plots and tabular data tables include items shown in Table 1. Where: I = Individual sample plots M = Multiple sample plot D = Dual Y axis plots S = Statistical plot T = Ta

39、bular data table, followed by the incremental value. Table 1: Matrix of Optional Plots and Tabular Data X-Axis Y-Axis TensionCompressionLoadDisplacementTimeTension Compression Load M DIM Displacement DIM 5.3.2 Option B. Report measured press-in force and retaining force single values. 6 Safety This

40、standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability o

41、f regulatory limitations prior to use. 7 Notes 7.1 Glossary. Press-in Force: The maximum force to install the snap-in fastener at +23 C 5 C. Retaining Force: The minimum force to disassemble the snap-in fastener at +80 C minimum. Snap-in Fastener: Type of fastener which can be installed without the

42、use of mechanical tools. For removal of these fasteners, the use of mechanical tools may be necessary. Some common examples are fir trees, push-pins, rosebuds, w-prongs, cantilever hooks, spring clips, push-in nuts, grommets, etc. 7.2 Acronyms, Abbreviations, and Symbols. ISO International Organizat

43、ion for Standardization MPD Master Process Document 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW15530 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking

44、 permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserved November 2012 Page 5 of 8 9 Release and Revisions This standard was originated in December 2006. It was first approved by the Fastening and Sealing Test Lab G

45、lobal Subsystem Leadership Team in January 2007. It was first published in May 2007. Issue Publication Date Description (Organization) 1 MAY 2007 Initial publication. 2 NOV 2012 Five year refresh of document. Updated GMW specifications, revised data reporting format to allow variations. (Fastening a

46、nd Sealing Test Lab GSSLT) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserve

47、d November 2012 Page 6 of 8 Appendix A: Test Required Information Worksheet Project Name: _ Model Year/Program: _ Request No: _ Requestor/Phone: _ Part Number Quantity Description Part Disposition at Completion: _ Required Completion Date: _ Master Process Document or Diagram Attached? Y N, If Yes,

48、MPD Number _ Maximum Requested Load If Applicable: _kN. Test Coupon Used? Y N, If Yes, Drawing or Sketch Required. Test Matrix Step No. Description Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15530 Copyright 2012 General Motors Company All Rights Reserved November 2012 Page 7 of 8 Appendix B: Test Data Summary Sheet General Motors