ImageVerifierCode 换一换
格式:PDF , 页数:12 ,大小:265.36KB ,
资源ID:757768      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-757768.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(GMW GMW16445-2013 DEXRON LS Gear Oil 75W - 90 Issue 3 English.pdf)为本站会员(deputyduring120)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

GMW GMW16445-2013 DEXRON LS Gear Oil 75W - 90 Issue 3 English.pdf

1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW16445 DEXRON LS Gear Oil 75W - 90 Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 1 of 12 1 Scope 1.1 Material Description. This specification covers DEXRON Limited Slip (LS) Gear Oil primarily for use in axles i

2、n cars and trucks with plate type LS differentials. This specification describes, in terms of laboratory and simulated service test results, the requirements for a minimum-performance fluid. 1.2 Symbols. Not applicable. 1.3 Typical Applications. For use in GM limited slip differentials. 1.4 Remarks.

3、 1.4.1 This specification may involve hazardous materials, operations, and equipment. This specification does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and

4、 to determine the applicability of regulatory limitations prior to use. 1.4.2 This specification uses International System of Units (SI) units as standard per ASTM SI 10, except for certain components, which are commercially available only in American conventional units. 1.4.3 This specification use

5、s the Rounding-off Method per ASTM E29 for significant figures to determine conformance to specification requirements. 1.4.4 Unless otherwise noted, part numbers of this specification refer to those of General Motors Powertrain. 2 References Note: Only the latest approved standards are applicable un

6、less otherwise specified. 2.1 External Standards/Specifications. ASTM D92 ASTM D1418 ASTM D5185 ASTM E29 ASTM D97 ASTM D1552 ASTM D5704 ASTM SI 10 ASTM D130 ASTM D2240 ASTM D5800 CEC L-45-99 ASTM D412 ASTM D2270 ASTM D6121 CEC L-48-A-00 ASTM D445 ASTM D2983 ASTM D6304 CEC L-84-02 ASTM D471 ASTM D405

7、2 ASTM D6594 FED-STD-791 ASTM D664 ASTM D4289 ASTM D6922 ISO 37 ASTM D892 ASTM D4629 ASTM D7038 SAE J306 ASTM D1193 ASTM D4739 ASTM D7450 SAE J2643 2.2 GM Standards/Specifications. 9986290 GMW3059 2.3 Additional References. All GM DEXRON testing forms including Form A are available from the Team Lea

8、der for Service Parts Engineering and DEXRON Licensing, or the GM Automatic Transmission Fluid (ATF) and Gear Oil Committee Chairman via GM Supply Power. Folders/ENGINEERING/Powertrain Product Engineering/Transmission. ( Analytical Balance, Sartorius, Model Number 2402 EHDPROC11 (test procedure run

9、at Imperial College, London, England) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16445 Copyright 2013 General Motors Company All Rig

10、hts Reserved December 2013 Page 2 of 12 FVA-2/IV (Pitting Test procedure) GM Aerated Seal Test (see Appendix B) Metered Fuel Economy Federal Fuel Economy (FFE) (Highway) Metered Fuel Economy Federal Test Procedure (FTP) (City) TMC003 Material Safety Data Sheet guidance documents (available at ) VW P

11、V 1454 (Volkswagen test procedure) 3 Requirements 3.1 Test Requirements. Form A (refer to 2.3) is required for testing to be started on gear lubricants pursuing DEXRON LS Gear Oil approval. 3.2 Mechanical Requirements. Test procedures shall be conducted as specified with no deviation unless express

12、written authorization is obtained from the General Motors Automatic Transmission Fluid and Gear Oil Committee. Test parts are to be used as received. Replacement or modification of any part shall be made only if directed in this specification or to replace damaged parts. The laboratory must target t

13、o the mean of the specified test conditions. 3.3 Physical Requirements. Fluids qualified under this specification shall conform SAE J306 and to the test methods and requirements as listed in Appendix A, Table A1. 3.4 Approved Additive Chemistries. Fluids meeting this specification shall be manufactu

14、red using additive chemistries listed in Appendix A, Table A2, DEXRON LS Gear Oil Approved Additive Chemistry Combinations. 3.5 Requirements for New Additive Chemistry Combinations. 3.5.1 Successful completion of a complete DEXRON LS Gear Oil Qualification Program (Appendix A, Table A1). 3.5.2 Succe

15、ssful completion of complete DEXRON LS Gear Oil Qualification Programs (Appendix A, Table A1) using the following fluid blends: 3.5.2.1 Seventy-five percent (75%) Candidate, 25% Reference Fluid. 3.5.2.2 Fifty percent (50%) Candidate, 50% Reference Fluid. 3.5.2.3 Twenty-five percent (25%) Candidate,

16、75% Reference Fluid. 3.5.2.4 If applicable, 50% Candidate, 50% any previously approved chemistry other than the Reference Fluid. 3.5.3 Successful completion of tests listed in Table A3. 3.5.4 Successful completion of a 241 000 km (150 000 mi) fleet test using the new candidate chemistry and blends o

17、f fluids from 3.5.2. A proposal for the fleet test shall be submitted to and approved by the GM Automatic Transmission Fluid (ATF) and Gear Oil Committee before commencing the fleet test. 3.5.5 Any additional testing as directed by the GM ATF and Gear Oil Committee. 3.6 Additional Requirements. 3.6.

18、1 The test requirements given in this specification are minimum or maximum acceptance limits for valid tests. No adjustments for test precision are to be applied as test variability was taken into account in the determination of the requirements. 3.6.2 The General Motors ATF and Gear Oil Committee r

19、eserves the right to require any additional tests that may be deemed necessary to ensure satisfactory performance of fluids submitted for qualification as DEXRON LS Gear Oil. 3.6.3 Validation Requirements. Testing necessary for validating the use of this lubricant shall be prescribed by Materials En

20、gineering. Testing will include, but not be limited to, tests included in Section 3 of this specification, vehicle fleet testing, and Proving Ground Durability Tests. 4 Manufacturing Process Not applicable. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot

21、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16445 Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 3 of 12 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws,

22、rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the English and domestic language, the English language shall take precedence. 5.3 Inspection and Rejection. All shipments of material or parts under contract or purchase order manufa

23、ctured to this specification shall be equivalent in every respect to the initial samples approved by Engineering. There shall be no changes in either formulation or manufacturing processes permitted without prior notification and approval by Engineering. Lack of notification by the supplier constitu

24、tes grounds for rejection of any shipment. While samples may be taken from incoming shipments and checked for conformance to this specification, the supplier shall accept the responsibility for incoming shipments meeting this specification without dependence upon purchasers inspection. The series of

25、 tests used to approve each batch of product along with acceptance limits will be agreed upon by the purchaser and seller. The laboratory providing the certificate of analysis must also participate in a proficiency testing program (round robin) that is approved by the Fuels, Fluids, and Lubricants G

26、lobal Subsystem Leadership Team (GSSLT) or designate. The Fuels, Fluids, and Lubricants GSSLT or designate must receive copies of the proficiency testing reports directly from the test program administrator. 5.4 Initial Source Approval. No shipment shall be made by any supplier until representative

27、initial production samples have been approved by the Fuels, Fluids, and Lubricants Global Subsystem Leadership Team or designees meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical co

28、mposition of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In ad

29、dition, product MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable

30、Substances for Parts. 5.7 Trademark Licensing. 5.7.1 Licenses to use the trademark DEXRON and related “GO“ identification numbers are issued for fluids which have been tested by an independent laboratory and/or by General Motors and subsequently approved by the General Motors Automatic Transmission

31、Fluid and Gear Oil Committee. Note: For information on qualification of service replacement fluids for use in General Motors axles, contact, the Team Leader for Service Parts Engineering and DEXRON Licensing or the GM ATF and Gear Oil Committee Chairman, via GM Supply Power. Folders/ENGINEERING/Powe

32、rtrain Product Engineering/Transmission. ( 6 Approved Sources Materials supplied to this specification must be approved by General Motors. The appropriate GM Materials Engineering department(s) must confirm material as meeting the requirements of this specification. Any test data sheets of material

33、submitted to General Motors for such confirmation (e.g., during Production Part Approval Process (PPAP) under this material specification must list all properties and must apply corresponding test methods of this material specification. 7 Notes 7.1 Glossary. Reference: Something of known performance

34、 characteristics, designated by the GM ATF and Gear Oil Committee. 7.2 Acronyms, Abbreviations, and Symbols. Al Aluminum Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WOR

35、LDWIDE ENGINEERING STANDARDS GMW16445 Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 4 of 12 ARKL Axialrillen-Kugellager ATF Automatic Transmission Fluid B Boron Ca Calcium cP Centipoise cST CentiStoke DKA Deutscher Koordinierungsausschuss im CEC Fe Iron FFE Federal Fue

36、l Economy - Highway Fuel Economy FTP Federal Test Procedure - City Fuel Economy FVA Forschungsvereinigung Antriebstechnik FZG Forschungsstelle fur Zahnrader und Getriebebau GHS Globally Harmonized System of Classification and Labeling of Chemicals GSSLT Global Subsystem Leadership Team IR Infrared K

37、 Potassium KV Kinematic Viscosity KRL Kugel Rollen Lager LS Limited Slip Mg Magnesium Mn Manganese MSDS Material Safety Data Sheet N Nitrogen Na Sodium Ni Nickel NVH Noise, Vibration and Harshness P Phosphorus PPAP Production Part Approval Process ppm parts per million S Sulfur Sb Antimony SDS Safet

38、y Data Sheet Si Silicon SI International System of Units SRE Standard Rubber Elastomer TAN Total Acid Number UHP Ultra-High Purity VI Viscosity Index WIP Wheel (Hop) Inducing Procedure Zn Zinc 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Material

39、per GMW16445 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16445 Copyright 2013 General Motors Company All Rights Reserved December 201

40、3 Page 5 of 12 9 Release and Revisions This standard was originated in October 2010. It was first approved by the GM ATF and Gear Oil Committee in August 2011. It was first published in August 2011. Issue Publication Date Description (Organization) 1 AUG 2011 Initial publication. 2 MAR 2012 Updated:

41、 Table A1: Brookfield Viscosity and DKA Oxidation Stability Requirement. (Materials-Fuels, Fluids & Lubricants) 3 DEC 2013 Updated Table A1 and Appendix B. (Fuels, Fluids & Lubricants Global Subsystem Leadership Team) Copyright General Motors Company Provided by IHS under license with General Motors

42、 CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16445 Copyright 2013 General Motors Company All Rights Reserved December 2013 Page 6 of 12 Appendix A Table A1: DEXRON LS Gear Oil Test Methods and Requirements Test Metho

43、d Requirement Appearance Visual Inspection Clear Amber Liquid Elemental Analysis ASTM D5185 Report, ppm (parts per million): Al, B, Ca, Fe, K, Mg, Mn, Na, Ni, P, Sb, Si, Zn ASTM D1552 Report, weight (percent) S ASTM D4629 Report, ppm: N Water Content ASTM D6304 0.10% weight maximum Fluid Profile Pro

44、prietary GM Test Report Miscibility & Homogeneity FED-STD-791 ASTM D6922 3430 -Compatibility 3440 -Storage Solubility No separation or color change at end of test using Reference Fluid PASS PASS Kinematic Viscosity ASTM D445 1. Report, cSt 10 C (50 F) 2. 80 cSt minimum 40 C (104 F) 3. 14.0 cSt minim

45、um 100 C (212 F) 4. Report, cSt 150 C (302 F) Viscosity Index ASTM D2270 165 minimum Density ASTM D4052 (15 C) Report, typical 0.856 g/mL Pour Point ASTM D97 -45 C maximum (-49 F) Fire Point ASTM D92 220 C minimum (428 F) Flash Point ASTM D92 150 C minimum (302 F) Total Base Number ASTM D4739 Report

46、 Total Acid Number ASTM D664 Report Brookfield Viscosity ASTM D2983 1. Report, cP -10 C (14 F) 2. 4500 cP maximum -20 C (-4 F) 3. Report, cP -30 C (-22 F) 4. 75 000 cP maximum -40 C (-40 F) Copper corrosion ASTM D130, 3 h, 121 C Better than 2A DKA Oxidation Stability CEC L-48-A-00 1. 60% KV100 incre

47、ase maximum 160 C for 192 h 2. 70% KV40 increase maximum Method B 3. VI Change, Report 4. TAN, Report 5. Flask sludge rating, report with picture 6. Blotter spot, provide picture 7. IR absorbance, report Shear Stability- KRL CEC L-45-99, 40 h 100 C (212 F) KV100 5/5 rating 2. Ridging 8/8 rating 3. R

48、ippling 8/8 rating 4. Pitting 9.3/9.3 rating 5. Scoring 9/9 rating Stressed L-37 ASTM D6121 1. Wear 5/5 rating (Modified Sequence 2) 2. Ridging 8/8 rating 16 h at 3. Rippling 8/8 rating 163 C 1.7 C 4. Pitting 9.3/9.3 rating 5. Scoring 9/9 rating L-60-1 Oxidation stability ASTM D5704 1. 25% KV100 (maximum) 2. 0.5% Pentane Insoluble (maximum) 3. 0.5% Toluene Insoluble (maximum) 4. Carb

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1