GMW GMW16592-2011 Electrical Electronic Commodity J2 Supplier Serviceability Addendum Issue 1 English《电气 电子商品J2供应商的可服务性附录 第1次出版(英文版本)》.pdf

1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW16592 Electrical/Electronic Commodity J2 Supplier Serviceability Addendum Copyright 2011 General Motors Company All Rights Reserved July 2011 Originating Department: North American Engineering Standards Page 1 of 3 1 Introduction Note: Nothin

2、g in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. The SOR Appendix J2 document, where used, contains specific program and commodity information that goes above and beyon

3、d that defined in the “Global Supplier Serviceability Requirements GMW15010” document (SOR Appendix J1). For those programs and commodities where an appendix J2 has been populated, the two documents must be used in conjunction to understand all of the serviceability requirements. 1.1 Scope. This spe

4、cification establishes the process for General Motors Customer Care and Aftersales Engineering to obtain the relevant diagnostic and programming data for specific programs to allow accurate authoring of diagnostic and programming software and service manual instructions. 1.2 Mission/Theme. The Suppl

5、ier Specification Process shall provide a reliable, effective, and flexible means to provide relevant diagnostic and programming specifications. 1.3 Classification. Not Applicable. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards

6、/Specifications. None 2.2 GM Standards/Specifications. GMW3059 GMW15010 2.3 Additional References. 3 Additional Modification to GMW 15010 3.1 Service Information, Diagnostic Scan Tool, and Service Programming. For all electrical/electronic control modules able to communicate via serial data where s

7、upplier is software and/or calibration responsible, the Supplier shall populate and submit a Diagnostic Application Chart to GM Customer Care and Aftersales. This document contains the program specific diagnostic content for all variations and configurations available for a given program. The suppli

8、er shall also submit the latest version of the Diagnostic Component Technical Specification as described in the appendix J1 for the commodity sourced. The details and timing of this deliverable are defined in the following paragraphs. 3.2 Retrieval of Latest Diagnostic Application Chart Template. Th

9、e Supplier shall obtain the latest Diagnostic Application Chart template from the GM SupplyPower website. The supplier shall choose the template for their specific commodity. If there is not a specific template for their commodity, choose the generic Diagnostic Application Chart template. 3.3 Delive

10、ry of Documentation. Once Supplier has completed the template, Supplier shall send the deliverable electronically to per the timing described in section 3.3.1. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permi

11、tted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16592 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 2 of 3 Note: The following terms are used in the subject lines shown: Electronic Control Unit (ECU), Integration Vehicle Engineering Release (IVER),

12、Model Year (MY), Product/Process Validation (PPV), Start of Regular Production (SORP). The “Subject Line” of the email shall include an identifier shown below: First Draft IVER: (MY and Program) (ECU Name) (Supplier Name) Final Plan Specification: -4 PPV (MY and Program) (ECU Name) (Supplier Name) L

13、aunch Intent Specification: -16 SORP (MY and Program) (ECU Name) (Supplier Name) 3.3.1 Timing of Deliverable. The supplier shall provide the documentation per the timing in the following table: Deliverable Timing First Draft IVER Final Plan Specification 4 PPV Launch Intent Specification 16 SORP Lat

14、e Changes managed via PDT After 16 SORP 3.4 Requests for Sample Populated Templates and Questions. At Suppliers request, a sample populated template can be provided. Supplier shall send any questions or sample requests to with one of the following “Subject Lines”. Sample Request: (ECU Name) (Suppli

15、er Name) Question: (ECU Name) (Supplier Name) 4 Validation 4.1 General. Supplier is responsible for validation of the specification to actual system operation. 5 Provisions for Shipping Not Applicable. 6 Notes 6.1 Glossary. None 6.2 Acronyms, Abbreviations, and Symbols. MY Model Year ECU Electronic

16、Control Unit IVER Integration Vehicle Engineering Release PPV Product/Process Validation SORP Start Of Regular Production 7 Additional Paragraphs 7.1 All parts or systems supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Coding

17、System This standard shall be referenced in other documents, drawings, etc., as follows: GMW16592 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STAN

18、DARDS GMW16592 Copyright 2011 General Motors Company All Rights Reserved July 2011 Page 3 of 3 9 Release and Revisions This standard was originated in April 2011 It was first approved by Customer Care and Aftersales Engineering in July 2011. It was first published in July 2011. Issue Publication Date Description (Organization) 1 JUL 2011 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-