GMW GMW16711-2012 Emblem Vitreous Enamel (Cloisonn Issue 1 English《釉瓷景泰蓝的标志 第1次出版(英文版本)》.pdf

1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW16711 Emblem Vitreous Enamel (Cloisonn) Copyright 2012 General Motors Company All Rights Reserved February 2012 Originating Department: North American Engineering Standards Page 1 of 3 1 Scope 1.1 Material Description. These emblems are cons

2、tructed of a Vitreous Enamel (Cloisonn) applied to a Gilders Bronze, UNS C21000 quarter hard per SAE J463, with chrome plate. 1.2 Symbols. Not applicable. 1.3 Typical Applications. This specification covers the performance requirements of a decorative exterior emblem. 2 References Note: Only the lat

3、est approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ASTM D870 SAE J2527 SAE J463 2.2 GM Standards/Specifications. GM6271M GMW3221 GMW14458 GMW14729 GMW3059 GMW3286 GMW14672 2.3 Additional References. TMC003 Material Safety Data Sheet guidance docu

4、ments (available at ). 3 Requirements 3.1 Requirements on Test Specimens. Reference GMW3221. Samples tested for initial submission purposes must meet all requirements of this specification. The requirements shown in 3.2, 3.3.1 and 3.3.2 shall be used for quality control purposes. All tests shall be

5、performed at 23 C 2 C and 50% Relative Humidity (RH) unless otherwise specified. 3.2 Plating Requirements. The chrome plated areas of the emblem shall meet the requirements of GMW14672. 3.2.1 Check plating thickness at all significant surfaces. 3.2.2 All plated surfaces shall be free of all surface

6、defects. 3.3 Corrosion Resistance. Vitreous Enamel (Cloisonn) shall show no adverse appearance defects (blisters, cracking, film lifting, etc.) or base metal corrosion. 3.3.1 Per GMW14729: 96 h humidity. 3.3.2 Per ASTM D870: 2 h water immersion. 3.3.3 Per GMW3286: 336 h neutral salt spray. 3.3.3.1 E

7、mblems must not show evidence of green, white, or red corrosion. 3.3.3.2 No surface corrosion after 80 h of neutral salt spray per GMW3286. 3.3.4 There shall be no evidence of base metal corrosion after exposure to 44 h Copper-Accelerated Acetic Acid Salt Spray (CASS) per GMW14458. 3.4 Weathering. 3

8、.4.1 Emblems must not show any evidence of objectionable surface deterioration, color or gloss change, or other undesirable effect after a 3500 kJ/m2 exposure at 340 N m in xenon arc weatherometer when set up as described in SAE J2527. Copyright General Motors Company Provided by IHS under license w

9、ith General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16711 Copyright 2012 General Motors Company All Rights Reserved February 2012 Page 2 of 3 3.4.2 Emblems mounted at a 5 angle from the horizon facing sout

10、h in Florida and at a 45 angle facing south in Arizona shall not show any evidence of objectionable surface deterioration when subjected to 14 644 MJ/m2 direct exposure. Objectionable surface deterioration shall be defined to include all visible surfaces. There shall be no objectionable change in co

11、lor, gloss, pitting or corrosion. In instances where xenon arc weatherometer and Florida/Arizona exposure results are in disagreement, the Florida/Arizona results will take precedence. 3.5 Adhesion. Emblems must meet the adhesive bond requirements as outlined in GM6271M. 3.6 Identification. All part

12、s shall be identified with a fabricators identification. If ink is used, it must not be easily rubbed off or cause any staining to materials with which it may come in contact. Any changes in marking inks must be approved by engineering before usage or adoption. 4 Manufacturing Process Not applicable

13、. 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the English and domestic language, the English language shall take precedence. 5.3 Inspect

14、ion and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval

15、must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the responsibility of the supplier to inform the customer in a timely manner,

16、 without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In ind

17、ividual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production samples have been approved by the appropriate Materials Engineering departme

18、nt(s) as meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must

19、be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety D

20、ata Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 6 Approved Sources Engineering qualifications of an approved source are required for this standard

21、. Only sources listed in the GM Materials File (MATSPC) under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, the responsible Engineering group should be contacted to obtain the approved source in that individual country.

22、Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16711 Copyright 2012 General Motors Company All Rights Reserved February 2012 Page 3 of 3

23、 7 Notes 7.1 Glossary. MATSPC: Global repository of GM Approved Materials for corresponding GM Engineering Standards. 7.2 Acronyms, Abbreviations, and Symbols. CASS Copper-Accelerated Acetic Acid Salt Spray GHS Globally Harmonized System of Classification Labeling of Chemicals MSDS Material Safety D

24、ata Sheet RH Relative Humidity SDS Safety Data Sheet 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Material per GMW16711 9 Release and Revisions This standard was originated in October 2011. It was first approved by the Emblems and Sill Plates GSSL

25、T in February 2012. It was first published in February 2012. Issue Publication Date Description (Organization) 1 FEB 2012 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-