GMW GMW16723-2012 Flame Resistance Test for Adhesives and Sealers Issue 1 English《粘合剂和密封材料的阻燃性试验 第1次出版(英文版本)》.pdf

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW16723 Flame Resistance Test for Adhesives and Sealers Copyright 2012 General Motors Company All Rights Reserved February 2012 Originating Department: GME Specification Center Page 1 of 2 1 Scope Note: Nothing in this standard supercedes applicable l

2、aws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This test procedure is intended to determine the flame resistance of adhesives and sealers located in or near a welding operation. 1.2 Foreword. Not

3、 applicable. 1.3 Applicability. This Test Procedure may be used for Body Shop adhesives and sealers. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. None 3 Resources 3.1 Faci

4、lities. Not applicable. 3.2 Equipment. 3.2.1 CRS steel panel. 3.2.2 Bunsen burner with natural gas fuel. 3.2.3 Panel / Flame apparatus. 3.3 Test Piece. All dimensions are as specified below, unless otherwise specified or agreed upon by the GM approving engineer. 3.3.1 2.5 mm x 35 mm x 130 mm long be

5、ad applied to a cleaned CRS steel panel of 250 mm x 100 mm. 3.4 Test Time. Calendar time: 1 day Test hours: 2 h Coordination hours: 1 h 3.5 Test Required Information. Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. See paragraph 4.3. 4.2 Conditions. 4.2.1 Environme

6、ntal Conditions. The test shall be performed at (+23 5) C. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. Copyright General Motors Company Provided by I

7、HS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16723 Copyright 2012 General Motors Company All Rights Reserved February 2012 Page 2 of 2 4.3 Instructions. 4.3.1 Apply a 2.5 mm x 35 m

8、m x 130 mm long bead on the CRS test panel. 4.3.2 Air dry sample for 30 minutes. 4.3.3 Adjust gas flow to have a 50 mm high flame. Air flow shall be adjusted to get 2 distinct inner and outer blue cones. 4.3.4 Position flame in that way, that the inner cone touch the material perpendicular to panel

9、at the edge of bead and turn drive motor on. Flame rate of travel shall be a uniform 25.5 mm/s. The flame travels across the width of the bead for 1 s and off for 1 s at both ends of travel. Travel per pass is 76 mm. The flame may also be held stationary with panel moving across flame. 4.3.5 Repeat

10、for number of cycles as described in the individual Material Specification. Unless stated otherwise in an individual Material Specification, the sample shall be self-extinguishing after the specified number of cycles. 4.3.6 Following cycle test, subject inverted sample directly into flame until igni

11、tion of sample occurs. 4.3.7 Remove sample from flame and re-invert. Report whether material is self-extinguishing. 5 Data 5.1 Calculations. Not applicable. 5.2 Interpretation of Results. Not applicable. 5.3 Test Documentation. Report whether material is self-extinguishing, or not. 6 Safety This sta

12、ndard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of r

13、egulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. CRS = Cold rolled steel 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW16723 9 Release and Revisions This standard was ori

14、ginated in November 2011. It was first approved by Preformed Sealer Team, Pumpable Sealer Team, Adhesive Team in January 2012. It was first published in February 2012. Issue Publication Date Description (Organization) 1 FEB 2012 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-